Principles of Instrumental Analysis
7th Edition
ISBN: 9781305577213
Author: Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 3, Problem 3.2QAP
Interpretation Introduction
Interpretation:
CMRR of amplifier is to be calculated.
Concept introduction:
CMRR stands for Common Mode Rejection Ratio. It represents how effectively the common mode signal (for example -noise) is rejected by a difference amplifier.
The formula to calculate CMRR is
where Ad and Ac represents difference mode and common mode gains of the difference amplifier respectively.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
4. What is the capacitance of an empty parallel-plate capacitor with metal plates that
each have an area of 1.00m², separated by 1.00 mm?
Design a voltage divider biased common emitter amplifier with a bypassed emitter resistance for a DC
supply of Vcc D (18+R)V and a quiescent current of 2mA. The voltage drop across collector should be
40% of DC supply voltage For the given design conditions: R = 02
Compute the circuit resistances.biased values of voltages and currents.
Draw the completely labelled circuit diagram.
If you wish to decrease the amount of current in a resistor from 240mA to 180mA by changing the 24V source, what should be the new voltage setting be?
Chapter 3 Solutions
Principles of Instrumental Analysis
Ch. 3 - Prob. 3.1QAPCh. 3 - Prob. 3.2QAPCh. 3 - Prob. 3.3QAPCh. 3 - Prob. 3.4QAPCh. 3 - Prob. 3.5QAPCh. 3 - Prob. 3.6QAPCh. 3 - Prob. 3.7QAPCh. 3 - Prob. 3.8QAPCh. 3 - Prob. 3.9QAPCh. 3 - Prob. 3.10QAP
Ch. 3 - Prob. 3.11QAPCh. 3 - Prob. 3.12QAPCh. 3 - Prob. 3.13QAPCh. 3 - Prob. 3.14QAPCh. 3 - Prob. 3.15QAPCh. 3 - Prob. 3.16QAPCh. 3 - Prob. 3.17QAPCh. 3 - Prob. 3.18QAPCh. 3 - Prob. 3.19QAPCh. 3 - Prob. 3.20QAPCh. 3 - Prob. 3.21QAPCh. 3 - Prob. 3.22QAPCh. 3 - Prob. 3.23QAPCh. 3 - Prob. 3.24QAPCh. 3 - Prob. 3.25QAP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- The table shows a series of standard additions of Cu(II)to acidified tap water samples measured by anodic stripping voltammetry at a platinum electrode. The unknown and all standard additions were made up to the same final volume. 1. Plot absorbance as a function of the concentration of Cu (II) standard. Determine the equation of the line and the X intercept. Find the concentration of Cu(II) in the water.arrow_forwardCalculate the expected voltage Cd | Cd+2 (0.00050M) || Cd+2 (0.69 M) | Cdarrow_forwardIf Q=96500 Coul and t=8 min ,then I will be The value of Z for the electrolyte ZnCl2 will be I=201.04 microamp Z=65/1 |=12062.5 amp Z=65/2 I=201.04 amp Z=65/2arrow_forward
- You are given two containers, one with 3.00 mg Mn 2+ and one with an unknown amount of Mn 2+ .You oxidize the Mn 2+ to the purple permanganate ion (MnO 4 - ) and dilute the solutions to 250.0 mLs.The solution containing the 3.00 mg Mn is used to prepare a third solution containing 1.50 mg Mn.The transmittances of the solutions are measured at 530 nm using a dilapidated Spectronic 20. Fromthe data below, calculate the amount of Mn in the unknown. For a linear curve, consider y=kx+b Mn (mg) %T3.00 30.81.50 55.2Unknown 37.4arrow_forwardAn air-gap parallel plate capacitor whose plates have an area of A=0,38m² are separated by a distance d=0,61m and are connected to a battery of V₁ = 1,8 V. The space between the parallel plates is partially filled (x=0,26m) with some material of dielectric constant K=4,56. Find the electric potential energy stored in the capacitor in terms of permitivity of free-space €0. Express your answer using 2 decimal places.arrow_forwardElectrochemical detection is commonly used in combination capillary electrophoresis systems. This is a type of hydrodynamic voltammetry called flow injection, where it has been shown that ilim a U1/3, where U is the flow rate of the solution. Flow analysis of a urine sample at a thin-layer amperometric detector, with a flow-rate of 1.25mL/min, yielded a limiting current value of 1.6µA for its unknown uric acid content. A larger current of 2.4µA was observed for a sample containing 1 × 10-4 M uric acid and flowing at a rate of 0.9mL/min. Calculate the original concentration of uric acid in the samplearrow_forward
- A coil with 193 turns has a magnetic flux of 37.3 nT-m² through each turn when the current is 1.90 mA. (a) What is the inductance of the coil? What are the (b) inductance and (c) flux through each turn when the current is increased to 3.53 mA? (d) What is the maximum emf & across the coil when the current through it is given by i = (2.72 mA)cos(wt), where w = 205 rad/s? (a) Number 3.788894737 Units mH (b) Number 3.788894737 Units mH (c) Number i 6.929947369 Units nWb (d) Number i 2.112687705 Units Varrow_forward3) The solution taken from a factory waste sample to prepare an internal standard contains Pb + 2 and Ag + 2, and the analysis peaks were determined as 298 mAU and 324 mAU. To analyze the unknown, a solution containing 0.150 M, 50.0 mL of Ag + 2 is put into the unknown liquid and completed to 100.0 mL. When the peaks are measured again, 670 mAU and 856 mAU signals are read from the samples. What is the concentration of Pb + 2 in the unknown liquid?arrow_forwardIf Q=96500 Coul and t=8 min ,then I will be The value of Z for the electrolyte ZnCl, will be O I=201.04 amp Z=65/2 O I=12062.5 amp Z=65/2 O I=201.04 microamp Z=65/1arrow_forward
- 7) A 25.0 ml sample containing Cu gave an instrument reading of 23.6 units (corrected for a blank). When exactly 0.500 ml of 0.0287M Cu(NO3)2 Was added to the solution,the signal increased to 37.9 units. Calculate the molar concentration of Cu" in the sample +2,arrow_forward9:01 A elearning.alsafwa.edu.iq الوقت المتبقي 0:43:09 1 Jlgw غير مجاب علیه بعد الدرجة من 3.00 علم هذا السؤال When a current of 0.4 A flows for 1.5 micro-seconds in a coper wire, estimate the number of electrons crossing the cross-section of the wire No. of electron= 4.8×10-19 electron No. of electron= 1.875×1012 electron No. of electron= 3x10-7 electron No. of electron= 4.8×10-26 electron الصفحة التالية الإعلاناتarrow_forwardThe molar absorptivity for aqueous solutions of phenol at 211 nm is 6.17 x 103 L cml mol-'. Calculate the permissible range of phenol concentrations if the transmittance is to be less than 85% and greater than 7% when the measurements are made in 1.00-cm cells.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning