Thermodynamics: An Engineering Approach
8th Edition
ISBN: 9780073398174
Author: Yunus A. Cengel Dr., Michael A. Boles
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 2.8, Problem 127FEP
A 2-kW electric resistance heater in a room is turned on and kept on for 50 min. The amount of energy transferred to the room by the heater is
- (a) 2 kJ
- (b) 100 kJ
- (c) 3000 kJ
- (d) 6000 kJ
- (e) 12,000 kJ
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2) The energy consumed by a shower for 30 days is 22kwh. It is known that the resistance of
the showerhead is 20 ohms and that its nominal current is 15A. So, what is the time in minutes
that the shower was turned on during this period?
An electric home stove with 3 burners and microwave is used in preparing a meal asfollows. Burner 1: 20 minutes Burner 2: 40 minutes Burner 3: 15 minutes . Microwave: 30minutes. If each burner is rated at 1.2 kW and the oven at 1.8 kW, and electricity costs 1000(IQ =Iraqi Dinar) per k Wh, calculate the cost of electricity used in preparing the meal?
A 13-V storage battery delivers current at the rate of 50 A. In a 27-min period, the heat lost from the battery is
92.74 kJ. What is the change in internal energy in kJ of the battery for the discharging period?
Chapter 2 Solutions
Thermodynamics: An Engineering Approach
Ch. 2.8 - What is total energy? Identify the different forms...Ch. 2.8 - List the forms of energy that contribute to the...Ch. 2.8 - How are heat, internal energy, and thermal energy...Ch. 2.8 - What is mechanical energy? How does it differ from...Ch. 2.8 - Natural gas, which is mostly methane CH4, is a...Ch. 2.8 - Portable electric heaters are commonly used to...Ch. 2.8 - Prob. 7PCh. 2.8 - Prob. 8PCh. 2.8 - 2–9E Calculate the total potential energy, in Btu,...Ch. 2.8 - Prob. 10P
Ch. 2.8 - Prob. 11PCh. 2.8 - At a certain location, wind is blowing steadily at...Ch. 2.8 - A water jet that leaves a nozzle at 60 m/s at a...Ch. 2.8 - Prob. 14PCh. 2.8 - Prob. 15PCh. 2.8 - Consider a river flowing toward a lake at an...Ch. 2.8 - When is the energy crossing the boundaries of a...Ch. 2.8 - Consider an automobile traveling at a constant...Ch. 2.8 - A gas in a pistoncylinder device is compressed,...Ch. 2.8 - A room is heated by an iron that is left plugged...Ch. 2.8 - A room is heated as a result of solar radiation...Ch. 2.8 - Prob. 23PCh. 2.8 - A small electrical motor produces 5 W of...Ch. 2.8 - Prob. 25PCh. 2.8 - 2–26C Lifting a weight to a height of 20 m takes...Ch. 2.8 - Prob. 27PCh. 2.8 - Prob. 28PCh. 2.8 - Prob. 29PCh. 2.8 - Prob. 30PCh. 2.8 - Prob. 31PCh. 2.8 - Prob. 32PCh. 2.8 - Prob. 33PCh. 2.8 - A ski lift has a one-way length of 1 km and a...Ch. 2.8 - The engine of a 1500-kg automobile has a power...Ch. 2.8 - Prob. 36PCh. 2.8 - What are the different mechanisms for transferring...Ch. 2.8 - On a hot summer day, a student turns his fan on...Ch. 2.8 - Prob. 39PCh. 2.8 - A vertical pistoncylinder device contains water...Ch. 2.8 - At winter design conditions, a house is projected...Ch. 2.8 - A water pump increases the water pressure from 15...Ch. 2.8 - Prob. 43PCh. 2.8 - Prob. 44PCh. 2.8 - A university campus has 200 classrooms and 400...Ch. 2.8 - Prob. 46PCh. 2.8 - Consider a room that is initially at the outdoor...Ch. 2.8 - Prob. 48PCh. 2.8 - 2-49 The 60-W fan of a central heating system is...Ch. 2.8 - Prob. 50PCh. 2.8 - An escalator in a shopping center is designed to...Ch. 2.8 - Prob. 52PCh. 2.8 - How is the combined pumpmotor efficiency of a pump...Ch. 2.8 - Prob. 54PCh. 2.8 - Can the combined turbinegenerator efficiency be...Ch. 2.8 - Consider a 2.4-kW hooded electric open burner in...Ch. 2.8 - Prob. 57PCh. 2.8 - Prob. 58PCh. 2.8 - Prob. 59PCh. 2.8 - A geothermal pump is used to pump brine whose...Ch. 2.8 - Prob. 62PCh. 2.8 - Prob. 63PCh. 2.8 - The water in a large lake is to be used to...Ch. 2.8 - A 7-hp (shaft) pump is used to raise water to an...Ch. 2.8 - At a certain location, wind is blowing steadily at...Ch. 2.8 - Reconsider Prob. 265. Using appropriate software,...Ch. 2.8 - Water is pumped from a lake to a storage tank 15 m...Ch. 2.8 - Prob. 69PCh. 2.8 - A hydraulic turbine has 85 m of elevation...Ch. 2.8 - Prob. 71PCh. 2.8 - Water is pumped from a lower reservoir to a higher...Ch. 2.8 - Prob. 73PCh. 2.8 - An oil pump is drawing 44 kW of electric power...Ch. 2.8 - How does energy conversion affect the environment?...Ch. 2.8 - What is acid rain? Why is it called a rain? How do...Ch. 2.8 - Why is carbon monoxide a dangerous air pollutant?...Ch. 2.8 - What is the greenhouse effect? How does the excess...Ch. 2.8 - What is smog? What does it consist of? How does...Ch. 2.8 - Prob. 80PCh. 2.8 - Consider a household that uses 14,000 kWh of...Ch. 2.8 - When a hydrocarbon fuel is burned, almost all of...Ch. 2.8 - Prob. 83PCh. 2.8 - A typical car driven 20,000 km a year emits to the...Ch. 2.8 - What are the mechanisms of heat transfer?Ch. 2.8 - Which is a better heat conductor, diamond or...Ch. 2.8 - How does forced convection differ from natural...Ch. 2.8 - What is a blackbody? How do real bodies differ...Ch. 2.8 - Define emissivity and absorptivity. What is...Ch. 2.8 - Does any of the energy of the sun reach the earth...Ch. 2.8 - The inner and outer surfaces of a 5-m 6-m brick...Ch. 2.8 - The inner and outer surfaces of a 0.5-cm-thick 2-m...Ch. 2.8 - Reconsider Prob. 292. Using appropriate software,...Ch. 2.8 - Prob. 94PCh. 2.8 - Prob. 95PCh. 2.8 - Prob. 96PCh. 2.8 - Prob. 97PCh. 2.8 - For heat transfer purposes, a standing man can be...Ch. 2.8 - Prob. 99PCh. 2.8 - Prob. 100PCh. 2.8 - A 1000-W iron is left on the ironing board with...Ch. 2.8 - A 7-cm-external-diameter, 18-m-long hot-water pipe...Ch. 2.8 - A thin metal plate is insulated on the back and...Ch. 2.8 - Reconsider Prob. 2103. Using appropriate software,...Ch. 2.8 - The outer surface of a spacecraft in space has an...Ch. 2.8 - Prob. 106PCh. 2.8 - A hollow spherical iron container whose outer...Ch. 2.8 - Consider a vertical elevator whose cabin has a...Ch. 2.8 - Consider a homeowner who is replacing his...Ch. 2.8 - Prob. 110RPCh. 2.8 - Prob. 111RPCh. 2.8 - Prob. 112RPCh. 2.8 - 2–113 The U.S. Department of Energy estimates that...Ch. 2.8 - Prob. 114RPCh. 2.8 - Prob. 115RPCh. 2.8 - Prob. 116RPCh. 2.8 - Prob. 117RPCh. 2.8 - Consider a TV set that consumes 120 W of electric...Ch. 2.8 - Water is pumped from a 200-ft-deep well into a...Ch. 2.8 - Prob. 120RPCh. 2.8 - Prob. 121RPCh. 2.8 - In a hydroelectric power plant, 65 m3/s of water...Ch. 2.8 - The demand for electric power is usually much...Ch. 2.8 - The pump of a water distribution system is powered...Ch. 2.8 - On a hot summer day, the air in a well-sealed room...Ch. 2.8 - Prob. 126FEPCh. 2.8 - A 2-kW electric resistance heater in a room is...Ch. 2.8 - A 900-kg car cruising at a constant speed of 60...Ch. 2.8 - Prob. 129FEPCh. 2.8 - Prob. 130FEPCh. 2.8 - Prob. 131FEPCh. 2.8 - A 2-kW pump is used to pump kerosene ( = 0.820...Ch. 2.8 - Prob. 133FEPCh. 2.8 - Prob. 134FEPCh. 2.8 - Prob. 135FEPCh. 2.8 - Prob. 136FEPCh. 2.8 - Prob. 137FEPCh. 2.8 - Heat is transferred steadily through a...Ch. 2.8 - The roof of an electrically heated house is 7 m...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Consider a subsonic compressible flow in cartesian coordinates where the velocity potential is given by (x,y)=V...
Fundamentals of Aerodynamics
Steady state conduction rate to the warm compressor to the net power produces theoretically by thermodynamic ba...
Introduction to Heat Transfer
19.8 Calculate the allowable tensile load for the connection shown. The plates are ASTM A36 steel and the weld ...
Applied Statics and Strength of Materials (6th Edition)
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
A windowmounted air conditioner removes 3.5kJ from the inside of a home using 1.75 kJ work input. How much ener...
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
Define or describe each type of fluid: (a) viscoelastic fluid (b) pseudoplastic fluid (c) dilatant fluid (d) Bi...
Fluid Mechanics: Fundamentals and Applications
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Consider the process of heating water on top of an electric range. What are the forms of energy involved during this process? What are the energy transformations that take place? Explain.arrow_forwardIf a house needs a minimum heat transfer rate of 75 kJ/h (i.e., 75 kJ of heat needs to be transferred into the house during one hour) to maintain a pleasant indoor temperature. If one wants to use a heat pump with a COP of 5.55 to fulfill this heat transfer rate, what is the corresponding electricity (in kWh) consumption to run such a heat pump for one hour?arrow_forwardA heat pump with a COP of 3.2 is used to heat a perfectly sealed house (no air leaks). The entire mass within the house (air, furniture, etc.) is equivalent to 1200 kg of air. When running, the heat pump consumes electric power at a rate of 5 kW. The temperature of the house was 7°C when the heat pump was turned on. If heat transfer through the envelope of the house (walls, roof, etc.) is negligible, the length of time the heat pump must run to raise the temperature of the entire contents of the house to 22°C is (a) 13.5 min (b) 43.1 min (c) 138 min (d) 18.8 min (e) 808 minarrow_forward
- By supplying energy to a house at a rate of 25,000 kJ/hr, a heat pump maintains the temperature of the dwelling at 20 C when the outside air is at -10 C. If electricity costs 8 cents per kW-hr, determine the minimum theoretical operating cost to heat the house for 24 hours. $1.97 O $1.37 $1.75 O $1.51 O$1.64arrow_forwardA refrigerator has a broken light bulb inside that is constantly turned on even when the refrigerator door is closed. If the light bulb uses 20 W of power and the refrigerator has a COP of 1.4, what would be the total cost of power consumption of the entire refrigerator? Assume electricity costs P12 per kWh and the refrigerator is opened an average of 15 times per day for 30 seconds.arrow_forwardA 2 kW electric resistance heater in a room is turned on and kept on for 30 min. The amount of energy transferred to the room by the heater is 1 kJ 60 kJ O 1800 kJ 3600 kJ O 7200 kJ O ООО Оarrow_forward
- A heat pump is used to extract heat from the outside atmosphere to heat the inside of a building. On a day when the outside air temperature is Tc°C, the heat pump is operating to a COP of 3.7, maintaining the inside temperature of the building at Th°C. If the building is losing heat at the rate of 53,709 kJ/hour in these conditions, determine how much power (kW) must be supplied to a heat pump? Keep two decimal placesarrow_forwardA garage is being retrofitted with a heat pump of COP=3. The garage heat losses are 10,000 BTU/h. How much would it cost to heat for one month (30 days) if electricity costs $0.14/kWh? How much will it cost to heat with an electrical baseboard (assume 100% efficiency)? Ans: heat pump - around $100 (exactly $98.5); electrical baseboard - $295.40arrow_forwardm = 0.9000 kg of water is heated with P = 481 W electric heater for t = 39 min . During this time the temperature of the water rises from T₁ = 335 K to its boiling point and me = 176 g of water evaporates. How much of the electric energy used by the heater is transferred to the water during the heating? Please consider that produced energy can be obtained by the product of power and time, so E = P t. Please use for the specific enthalpy of evaporation hf = 2260 and heat capacity of water values cp = 4.1900 kJ kgK What is the Percentage of electric energy transferred to water? EP = %arrow_forward
- m = 0.9000 kg of water is heated with P = 481 W electric heater for t = 39 min. During this time the temperature of the water rises from T₁ = 335 K to its boiling point and me = 176 g of water evaporates. How much of the electric energy used by the heater is transferred to the water during the heating? Please consider that produced energy can be obtained by the product of power and time, so E = P t. Please use for the kJ specific enthalpy of evaporation hf = 2260 kJ and heat capacity of water values p = 4.1900 kgK What is the Percentage of electric energy transferred to water? EP = 1 % Insert only 3 most significant digits of your answer without rounding. Quantity Symbol Total mass of water Mass of water that evaporates Power of electric heater Heating time Percentage of electric energy transferred to water Initial temperature of water Boiling point of water Specific enthalpy of vaporization for water • ÉASZ SÁN m me P t EP T₁ Tb he Specific heat capacity of liquid water Electric…arrow_forwardA vertical piston cylinder assembly containing water is being heated on a stove. During this process, 100 BTU of heat is transferred to the water. In the water's expansion process (because of the heat addition) 8000 ft- Ibf of work is done. Also, there is 20 BTU heat loss from the assembly. What is the water's change of energy as a result of the heat addition process? Mof 2629 k/ks ot 70arrow_forwardAn engine uses about 0.24 kg of fuel/kW-hr. If the heating value of the fuel is 50 MJ/kg, what is the thermal efficiency?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license