Concept explainers
What is the metal removal rate in Problem 11 if the depth of cut is 6.35 mm
Want to see the full answer?
Check out a sample textbook solutionChapter 27 Solutions
DeGarmo's Materials and Processes in Manufacturing
Additional Engineering Textbook Solutions
Introduction to Heat Transfer
Heating Ventilating and Air Conditioning: Analysis and Design
Applied Statics and Strength of Materials (6th Edition)
Statics and Mechanics of Materials (5th Edition)
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Engineering Mechanics: Dynamics (14th Edition)
- What would a .010 - .020 cutback of a 14.500 Diameter be?arrow_forwardwhat is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25 feet?arrow_forwardQUESTION 5 Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. O N=287 RPM, F-25.8 in/min, P=9.7 hp ON=2866 RPM, F=258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N= 11460 RPM, F-340 in/min, P=130 hp ON= 1146 RPM, F-34 inimin, P= 13 hp ON= 115 RPM, F-3.4 in/min, P=1.3 hp QUESTION 6 It is required to face mill an aluminum block to size it down from 2" to 1.5" thick using a 3" diameter 2-toothed carbide cutting tool. The block is 6.0" wide and 6" long. The entire tool diameter engages the workpiece during the cut. Calculate the recommended spindle speed in revolutions per minute, feed per tooth, and cutting power required. O N=1529 RPM, f= 0.026 in/rev/tooth, P = 36 hp O N-3820 RPM, f= 26 in/revitooth, P=27 hp O N-3820 RPM, f= 0.052 in/rew/tooth, P=27 hp ON-382 RPM, F= 0.026 in/revitooth, P = 0.027 hp O N-3820 RPM, f= 0.052 in/rev/tooth, P=2.7 hp…arrow_forward
- What is the cutting speed of a medium carbon steel which cutting stroke per minute is 80 and which length is 10".arrow_forwardWhich formula is used for calculation of specific cutting pressure?arrow_forwardIn a multi point cutting tool the negative rake angle is used for high tensile strength materials. Select one: True Falsearrow_forward
- What two terms refer to the squareness of a cut?arrow_forwardA lathe cross slide uses a diameter-reading micrometer collar. If the cross slide is advanced by 0.150". what depth of cut would result?arrow_forwardWhen threading, what is the reason for feeding the cutting tool at an angle for each depth cut?arrow_forward
- List all the failure modes, wear mechanisms and wear conditions for cutting toolsarrow_forwardHow many passes will it take to reduce the diameter from 5 % (five and one fourth) inches into 3 % (three and three fourth) inch if the depth of cut is 1/16 inch.arrow_forwardWhich type of feature doesn't belong to form tolerances? Circularity The profile of a surface Flatness Cilindricity Which option about chief elements in metal cutting is wrong? Feed s is the tool distance moved along the axis per revolution of the workarrow_forward
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning