QUESTION 5Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool.O N=287 RPM, F-25.8 in/min, P=9.7 hpON=2866 RPM, F=258 in/min, P=97 hpON=1146 RPM, F-25.8 in/min, P=97 hpO N= 11460 RPM, F-340 in/min, P=130 hpON= 1146 RPM, F-34 inimin, P= 13 hpON= 115 RPM, F-3.4 in/min, P=1.3 hpQUESTION 6It is required to face mill an aluminum block to size it down from 2" to 1.5" thick using a 3" diameter 2-toothed carbide cutting tool. The block is 6.0" wide and 6" long. The entire tool diameterengages the workpiece during the cut.Calculate the recommended spindle speed in revolutions per minute, feed per tooth, and cutting power required.O N=1529 RPM, f= 0.026 in/rev/tooth, P = 36 hpO N-3820 RPM, f= 26 in/revitooth, P=27 hpO N-3820 RPM, f= 0.052 in/rew/tooth, P=27 hpON-382 RPM, F= 0.026 in/revitooth, P = 0.027 hpO N-3820 RPM, f= 0.052 in/rev/tooth, P=2.7 hpO N-382 RPM, F= 0.052 in/rev/tooth, P = 0.027 hp

As two questions are independent so I am answering Q.5 as per bartleby policy. Please post Q.6…

Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. ON=287 RPM, F-25.8 inimin, P=9.7 hp ON=2866 RPM, F-258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N=11460 RPM, F-340 in/min, P-130 hp ON=1146 RPM, F-34 in/min, P=13hp ON=115 RPM, F-3.4 inmin, P=1.3 hp

Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. ON=287 RPM, F-25.8 inimin, P=9.7 hp ON=2866 RPM, F-258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N=11460 RPM, F-340 in/min, P-130 hp ON=1146 RPM, F-34 in/min, P=13hp ON=115 RPM, F-3.4 inmin, P=1.3 hp

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A long workpiece, with the length-to-dimeter ratio that exceeds factor 10, is to be machined. Which workholding should provide the lowest deflection? Collet in the spindle and a live center in the tailstock Chuck on the spindle, a live center in the tailstock, and a follower rest Mandrel Solid center with a dog and a dog plate on the spindle, a live center in the tailstock Faceplate
Please do Asap
Q.4 A single point cutting tool designated as follows 8-14-6-6-6-20-1 is used to machine a work with feed rate of 1mm/rev. Then the maximum height of roughness and average roughness, in mm, are respectively -3 A 0.0350, 8.76×10 B 8.76x10, -3 0.0350 C 0.10123, 0.0253 D 0.0253, 0.10123
Briefly describe the meaning of spark gap in wire cut machining by drawing a sketch.
The part in Figure 1 is to be drilled on a turret-type drill press. The part is 15.0 mm thick. Threedrill sizes will be used: 8 mm, 10 mm, and 12 mm, which are to be specified in the part programby tool turret positions TO1, T02, and T03. All tooling is high speed steel. Cutting speed = 75mm/min and feed = 0.08 mm/rev. Use the lower-left corner of the part as the origin in the x-y axissystem. Write the part program in the word address format using absolute positioning.
A cylindrical rod is machined using turning processes. It is given that the cutting speed is 120min ¹, and feed per tooth is 0.0025 m/min. The outer diameter is 35mm, the length of the rod is 130m and the inner diameter is 22mm. The number of teeth is 6. Find Rotational speed, Feed rate, Machining time, and Depth of cut.
Calculate the feed rate for a two-flute 1/ 4@in.-diameter carbide end mill to machine low-carbon steel.
Calculate the spindle speed (rpm) for turning operation when the cutting speed is 107.00 m/min and external diameter is D44.00 mm? (Two decimal places; Don't input units.) Your Answer: Answer
Need accurate answer for this please
To facilitate the milling (roughing) work of a cast steel material using a 1.5 inch diameter cutter choose between the two available stock. Find the speed of the cutter in rpm. – high speed steel cutter with a cutting speed of 50 fpm or – carbide tipped cutter with a cutting speed of 200 fpm.
How much machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by turning using a carbide insert. If the approach length and over run length is = 5 mm, Cutting speed is 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm D
Handwritten solution recommended. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.