Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 23, Problem 40QLP
Refer to Fig. 23.11b, and in addition to the tools shown, describe other types of cutting tools that can be placed in toolholders to perform other machining operations.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2 1.23 Tool life can be almost infinite at low cutting speeds.Would you then recommend that all machining be done at low speeds? Explain.
Estimate the machining time required in rough turning a 2.0-m-long, annealed aluminum-alloy round bar that is 75 mm in diameter, using (a) a high-speed steel tool; and (b) a carbine tool. Use a feed of 2 mm/rev. Assume max cutting speed for high-speed tools is moving 4 m/s and for carbide tools is moving 7 m/s.
Title
It has been stated that it is generally undesirable to allow temperatures to rise excessively in...
Description
It has been stated that it is generally undesirable to allow temperatures to rise excessively in
machining operations. Explain why.
By the student. This is an open-ended problem with a large number of acceptable answers.
The consequences of allowing temperatures to
rise to high levels in cutting include:
(a) Tool wear will be accelerated due to high
temperatures.
(b) High temperatures will cause dimensional
changes in the workpiece, thus reducing dimensional accuracy.
(c) Excessively high temperatures in the
cutting zone may induce metallurgical
changes and cause thermal damage to the
machined surface, thus affecting surface
integrity.
Chapter 23 Solutions
Manufacturing Engineering & Technology
Ch. 23 - Describe the types of machining operations that...Ch. 23 - What is turning? What kind of chips are produced...Ch. 23 - What is the thrust force in turning? What is the...Ch. 23 - What are the components of a lathe?Ch. 23 - (a) What is a tracer lathe? (b) What is an...Ch. 23 - Describe the operations that can be performed on a...Ch. 23 - Why were power chucks developed?Ch. 23 - Explain why operations such as boring on a lathe...Ch. 23 - Why are turret lathes typically equipped with more...Ch. 23 - Describe the differences between boring a...
Ch. 23 - How is drill life determined?Ch. 23 - What is the difference between a conventional...Ch. 23 - Why are reaming operations performed?Ch. 23 - Explain the functions of the saddle on a lathe.Ch. 23 - Describe the relative advantages of (a)...Ch. 23 - Explain how external threads are cut on a lathe.Ch. 23 - Prob. 17RQCh. 23 - Explain the reasoning behind the various design...Ch. 23 - Note that both the terms tool strength and...Ch. 23 - (a) List and explain the factors that contribute...Ch. 23 - Explain why the sequence of drilling, boring, and...Ch. 23 - Why would machining operations be necessary even...Ch. 23 - A highly oxidized and uneven round bar is being...Ch. 23 - Describe the difficulties that may be encountered...Ch. 23 - (a) Does the force or torque in drilling change as...Ch. 23 - Explain the similarities and differences in the...Ch. 23 - Describe the advantages and applications of having...Ch. 23 - Assume that you are asked to perform a boring...Ch. 23 - Explain the reasons for the major trend that has...Ch. 23 - Describe your observations concerning the contents...Ch. 23 - The footnote to Table 23.12 states that as the...Ch. 23 - In modern manufacturing, which types of metal...Ch. 23 - Sketch the tooling marks you would expect if a...Ch. 23 - What concerns would you have in turning a powder...Ch. 23 - The operational severity for reaming is much lower...Ch. 23 - Review Fig. 23.6, and comment on the factors...Ch. 23 - Explain how gun drills remain centered during...Ch. 23 - Comment on the magnitude of the wedge angle on the...Ch. 23 - If inserts are used in a drill bit (see Fig....Ch. 23 - Refer to Fig. 23.11b, and in addition to the tools...Ch. 23 - Calculate the same quantities as in Example 23.1...Ch. 23 - Estimate the machining time required to rough turn...Ch. 23 - A high-strength cast-iron bar 8 in. in diameter is...Ch. 23 - A 0.30-in.-diameter drill is used on a drill press...Ch. 23 - In Example 23.4, assume that the workpiece...Ch. 23 - For the data in Problem 23.45, calculate the power...Ch. 23 - A 6-in.-diameter aluminum cylinder 10 in. in...Ch. 23 - A lathe is set up to machine a taper on a bar...Ch. 23 - Assuming that the coefficient of friction is 0.25,...Ch. 23 - A 3-in.-diameter, gray cast iron cylindrical part...Ch. 23 - Would you consider the machining processes...Ch. 23 - Would it be difficult to use the machining...Ch. 23 - If a bolt breaks in a hole, it typically is...Ch. 23 - An important trend in machining operations is the...Ch. 23 - Review Fig. 23.8d, and explain if it would be...Ch. 23 - Boring bars can be designed with internal damping...Ch. 23 - A large bolt is to be produced from extruded...Ch. 23 - Make a comprehensive table of the process...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour and 40 minutes, at a spindle speed of 30 m/min. Calculate the tool life if it has to be operated at a speed of 40% higher than the initial cutting speed. Also calculate the cutting speed if the tool is required to have a life of 2 hours and 45 minutes. Assume Taylor's exponent valuen is 0.28.arrow_forwardDiscuss three (3) advantages of using cutting fluids in machining operation.arrow_forwardIn machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour and 40 minutes, at a spindle speed of 25 m/min. Calculate the tool life if it has to be operated at a speed of 30% higher than the initial cutting speed. Also calculate the cutting speed if the tool is required to have a life of 2 hours and 45 minutes. Assume Taylor’s exponent value n is 0.28.arrow_forward
- 3. It is required to machine a slot with length 100 mm, width 15 mm, and depth 4 mm. Calculate the length and pitch of the broach assuming a super-elevation of 0.15 mm/tooth. Calculate the main power in KW if the specific cutting resistance is 2000 N/mm2 and the cutting speed of 10 m/min is used.arrow_forwardInvestigate the non-traditional machining methods. Describe each in your own words and sketch out the process and appropriate scale (inches/microns etc). Then tabulate the material removal mechanism, workpiece materials, applications, costs/speed, advantages and limitations/disadvantages of each. The slides are for your starting point. List references, articles, videos, etc... Mechanical Methods 1. Water Jet Machining (WJM) 2. Abrasive Water Jet Machining (AWJM) 3. Ultrasonic Machining (USM) Non-Mechanical Methods 1. Electrochemical Machining (ECM) 2. Electro-Discharge Machining (EDM) 3. Wire EDM 4. Laser Drilling 5. Electron beam machining (EBM)arrow_forwardEstimate the machining time that will be required to finish a vertical flat surface of length 100 mm and depth 20 mm by an end mill cutter of 32 mm diameter and 60 mm length in a milling machine. Assume cutting speed of 30 m/min and feed of 0.12 mm/tooth. Let over run distance equal to approach distance.arrow_forward
- 11. Estimate the machining time required to rough turn a 0.5 m long annealed copper alloyRound bar from a 60 mm diameter to a 58 mm diameter, using a high-speed tool. Estimate the time required for an uncoated carbide tool.arrow_forward3) Explain the advantages and any disadvantages of indexable cutting inserts. Why were they developed? 4) How does the coefficient of friction affect the relationship between the friction force and the normal force on the tool face? 5) A turning operation is being carried out on a long, round bar at a constant depth of cut. Explain what differences, if any, there may be in the machined diameter from one end of the bar to the other. Give reasons for any changes that may occur.arrow_forwardIn an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?arrow_forward
- 22 .42 List and explain the considerations involved in determining whether a cutting tool should be reconditioned, recycled, or discarded after use.arrow_forwardA tool with zero rake angle used in orthogonal cutting when its clearance angle a is changed from 10 to 7 deg, Calculate the approximate % change in the life of the tool.arrow_forwarda) It has been stated that it is generally undesirable to allow temperatures to riseexcessively in machining operations. Explain why?b) List out the cutting parameters which is influenced the rises of cuttingtemperature during turning process.c) Evaluate the relationship of these cutting parameters to the cutting temperaturewith graph.d) Propose the solution of how to reduce the temperature during the cuttingprocess.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License