Engineering Mechanics: Dynamics (14th Edition)
14th Edition
ISBN: 9780133915389
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 21.4, Problem 52P
The 5-kg circular disk is mounted off center on a shaft which is supported by bearings at A and B. If the shaft is rotating at a constant rate of ω = 10 rad/s, determine the vertical reactions at the bearings when the disk is in the position shown.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The position of the small 0.68-kg blocks in the smooth radial slots in the disk which rotates about a vertical axis at O is used to activate a speed-control mechanism. If each block moves from r = 162 mm to r = 200 mm while the speed of the disk changes slowly from 272 rev/min to 382 rev/min, design the spring by calculating the spring constant k of each spring. The springs are attached to the inner ends of the slots and to the blocks.
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μkμk = 0.2. Neglect the mass of the
Determine the angular acceleration of the disk measured counterclockwise .
Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
The 10-kg wheel is rolling under the constant moment of M = 97 N-m. The wheel has radius r= 0.59 m, has mass center at point G, and
the radius of gyration is kg = 0.27 m. The coefficients of friction between the wheel and the ground is ls = 0.25 and Hk = 0.14. If the
wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s2). Please pay attention: the numbers
may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?.
M
G
Chapter 21 Solutions
Engineering Mechanics: Dynamics (14th Edition)
Ch. 21.1 - Show that the sum of the moments of inertia of a...Ch. 21.1 - Determine the moment of inertia of the cone with...Ch. 21.1 - Determine moment of inertia Iy of the solid formed...Ch. 21.1 - Determine the moments of inertia Ix and Iy of the...Ch. 21.1 - The density of the material is . Express the...Ch. 21.1 - Prob. 6PCh. 21.1 - Prob. 7PCh. 21.1 - Prob. 8PCh. 21.1 - The weight of the cone is 15 lb, the height is h =...Ch. 21.1 - The density of the material is .
Ch. 21.1 - Prob. 11PCh. 21.1 - Determine the moment of inertia Ixx of the...Ch. 21.1 - Determine the product of inertia Iyz of the...Ch. 21.1 - Prob. 14PCh. 21.1 - Prob. 15PCh. 21.1 - Determine the moment of inertia of the rod about...Ch. 21.1 - Prob. 17PCh. 21.1 - Prob. 18PCh. 21.1 - Prob. 19PCh. 21.1 - Prob. 20PCh. 21.1 - Prob. 21PCh. 21.3 - If a body contains no planes of symmetry, the...Ch. 21.3 - Prob. 23PCh. 21.3 - Prob. 24PCh. 21.3 - The large gear has a mass of 5 kg and a radius of...Ch. 21.3 - Prob. 26PCh. 21.3 - Prob. 27PCh. 21.3 - Prob. 28PCh. 21.3 - Prob. 29PCh. 21.3 - Prob. 30PCh. 21.3 - Prob. 31PCh. 21.3 - Prob. 32PCh. 21.3 - The 20-kg sphere rotates about the axle with a...Ch. 21.3 - The 200-kg satellite has its center of mass at...Ch. 21.3 - Prob. 35PCh. 21.3 - Prob. 36PCh. 21.3 - Prob. 37PCh. 21.3 - Prob. 38PCh. 21.3 - Prob. 39PCh. 21.3 - Prob. 40PCh. 21.4 - Derive the scalar form of the rotational equation...Ch. 21.4 - Prob. 42PCh. 21.4 - Prob. 43PCh. 21.4 - Prob. 44PCh. 21.4 - The disk has a weight of 15 lb. Neglect the weight...Ch. 21.4 - Prob. 46PCh. 21.4 - Prob. 47PCh. 21.4 - Prob. 48PCh. 21.4 - Prob. 49PCh. 21.4 - Prob. 50PCh. 21.4 - Prob. 51PCh. 21.4 - The 5-kg circular disk is mounted off center on a...Ch. 21.4 - Prob. 53PCh. 21.4 - Prob. 54PCh. 21.4 - Prob. 55PCh. 21.4 - The 4-kg slender rod AB is pinned at A and held at...Ch. 21.4 - Prob. 57PCh. 21.4 - Prob. 58PCh. 21.4 - Prob. 59PCh. 21.4 - Show that the angular velocity of a body, in terms...Ch. 21.4 - Prob. 61PCh. 21.6 - The gyroscope consists of a uniform 450-g disk D...Ch. 21.6 - Prob. 63PCh. 21.6 - Prob. 64PCh. 21.6 - Prob. 65PCh. 21.6 - When viewed from the front of the airplane, the...Ch. 21.6 - Prob. 67PCh. 21.6 - Prob. 68PCh. 21.6 - Prob. 69PCh. 21.6 - Prob. 70PCh. 21.6 - Prob. 71PCh. 21.6 - Prob. 72PCh. 21.6 - Prob. 73PCh. 21.6 - Prob. 74PCh. 21.6 - Prob. 75PCh. 21.6 - Prob. 76PCh. 21.6 - Prob. 77PCh. 21.6 - Prob. 78P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The 214-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 94 N•m, it starts rolling from rest. Determine the average friction force that the ground applies to the wheel if it has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s². M Your Answer: Answer unitsarrow_forwardThe wheel and attached spool have a combined weight of 50 lb and a radius of gyration about its center of kA = 6 in. If pulley B mounted on the engine is subjected to a torque M = 62.5 lb.ft, determine the total work exerted on the system if the pulley has made 9 revolutions. Shipping weight is 280 lbs. 3 in. M 3 in. M 7.5 in. 7.5 in. 4.5 in. 4.5 in.arrow_forwardThe 29-kg wheel is rolling under the constant moment of M = 85 N·m. The wheel has radius r = 0.57 m, has mass center at point G, and the radius of gyration is kg = 0.25 m. The coefficients of friction between the wheel and the ground is g = 0.37 and μk = 0.16. If the wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s²). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answerarrow_forward
- The 25-kg wheel is rolling under the constant moment of M = 73 N-m. The wheel has radius r= 0.52 m, has mass center at point G, and the radius of gyration is kG = %3D 0.21 m. The coefficients of friction between the wheel and the ground is ls = 0.26 and lk = 0.18. If the wheel rolls without slipping, determine the angular acceleration of the wheel (in rad/s²). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M G Your Answer: Answerarrow_forwardThe 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μk = 0.2. Neglect the mass of the cord Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.arrow_forwardThe uniform 50-kg sphere has radius r = 0.2 m and is welded to the center of the uniform 30-kg shaft as shown. When a constant couple moment M is applied to the shaft, its angular velocity reaches 74 rad/s after 4 s. Determine the magnitude of the moment M. Write your answer in N.m but do not write the units. M R= 0.1 m Taylor e m Te am Answer: Answerarrow_forward
- A single-cylinder reciprocating engine has a reciprocating mass of 6 kg. the crank rotates at 60 rpm and the stroke is 32 mm the mass of the revolving parts at 16 mm radius is 4 kg, if two-thirds of the reciprocating parts and the whole of the revolving parts are to be balanced. Determine the balance mass required at a radius of 35 mm and unbalanced force when the crank has turned 50° from the TDC. d luokarrow_forwardThe 30-kg wheel has a radius of gyration about its center O of ko = 240 mm, and radius r = 0.5 m. When the wheel is subjected to the constant force F = 388 N, applied to the wheel's center axle at an angle = 6°, it starts rolling from rest. Determine the total angular impulse L (in N•m.s) about the wheel's IC after 3.7 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². Your Answer: G Answer Ө Farrow_forwardThe 17-kg wheel is rolling under the constant moment of M = 85 N-m. The wheel has radius r= 0.50 m, has mass center at point G, and the radius of gyration is kg = 0.20 m. The coefficients of friction between the wheel and the ground is ls = 0.27 and Hk; = 0.22. If the wheel rolls while slipping, determine the angular acceleration of the wheel (in rad/s?). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M Garrow_forward
- The 150-kg pendulum has a center of mass at G and a radius of gyration about G of kG = 0.25m, as shown in Figure 2. Determine the horizontal and vertical components of reaction on thebeam by the pin A and the normal reaction of the roller B at horizontal direction when thependulum is rotating at 5 rad/s. Neglect the weight of the beam and the support. If the normalreaction of the roller B at horizontal direction change to vertical direction, determine thehorizontal and vertical components of reaction on the beam by the pin A.arrow_forwardThe dump truck carries 5 m³ of dirt with a density of 1600 kg /m³, and the elevating mechanism rotates the dump about the pivot A at a constant angular rate of 4 deg /s. The mass center of the dump and load is at G. Determine the maximum power P required during the tilting of the load. 1500 mm 900 mmarrow_forwardThe body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slippingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY