Engineering Mechanics: Dynamics (14th Edition)
14th Edition
ISBN: 9780133915389
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 21.4, Problem 51P
To determine
The components of reaction at the bearings and the angular acceleration of the door.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 740 kg and an
average gear-tooth force of 2.60 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B,
calculate the average offset X of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting
rollers.
Assumer = 110 mm, R= 695 mm, 0 = 24°
Detail of contact
at B
Answer: X
mm
The frame is made from uniform rod which has a mass p per unit length. A smooth recessed slot constrains the small rollers at A and B
to travel horizontally. Force P is applied to the frame through a cable attached to an adjustable collar C. Determine the magnitudes and
directions of the normal forces which act on the rollers if (a) h = 0.25L, (b) h = 0.50L, and (c) h = 0.81L. The forces will be positive if up,
negative if down. Evaluate your results for p = 2.5 kg/m, L = 510 mm, and P = 43 N. What is the acceleration of the frame in each case?
Answers:
(a)
(b)
L
(c)
h=
0.25L:
h =
0.50L:
h =
0.81L:
L
A
A
A
=
B
i
i
i
h
P
N.
N.
N₁
B
i
i
i
N.
N.
N.
i
i
i
m/s
m/s
m/s
Problem 6 - Part B
250 N
The cart and its load have a total mass of
200 kg and center of mass at G. A force of
P = 250 N is applied to the handle. Neglect
the mass of the wheels. Determine the
normal reactions at each of the two wheels
at A and B. Also, find an acceleration of the cart.
1.2 m
OB
0.3 m
0.4 m
0.6 m
ΘΑ
0.5 m
Chapter 21 Solutions
Engineering Mechanics: Dynamics (14th Edition)
Ch. 21.1 - Show that the sum of the moments of inertia of a...Ch. 21.1 - Determine the moment of inertia of the cone with...Ch. 21.1 - Determine moment of inertia Iy of the solid formed...Ch. 21.1 - Determine the moments of inertia Ix and Iy of the...Ch. 21.1 - The density of the material is . Express the...Ch. 21.1 - Prob. 6PCh. 21.1 - Prob. 7PCh. 21.1 - Prob. 8PCh. 21.1 - The weight of the cone is 15 lb, the height is h =...Ch. 21.1 - The density of the material is .
Ch. 21.1 - Prob. 11PCh. 21.1 - Determine the moment of inertia Ixx of the...Ch. 21.1 - Determine the product of inertia Iyz of the...Ch. 21.1 - Prob. 14PCh. 21.1 - Prob. 15PCh. 21.1 - Determine the moment of inertia of the rod about...Ch. 21.1 - Prob. 17PCh. 21.1 - Prob. 18PCh. 21.1 - Prob. 19PCh. 21.1 - Prob. 20PCh. 21.1 - Prob. 21PCh. 21.3 - If a body contains no planes of symmetry, the...Ch. 21.3 - Prob. 23PCh. 21.3 - Prob. 24PCh. 21.3 - The large gear has a mass of 5 kg and a radius of...Ch. 21.3 - Prob. 26PCh. 21.3 - Prob. 27PCh. 21.3 - Prob. 28PCh. 21.3 - Prob. 29PCh. 21.3 - Prob. 30PCh. 21.3 - Prob. 31PCh. 21.3 - Prob. 32PCh. 21.3 - The 20-kg sphere rotates about the axle with a...Ch. 21.3 - The 200-kg satellite has its center of mass at...Ch. 21.3 - Prob. 35PCh. 21.3 - Prob. 36PCh. 21.3 - Prob. 37PCh. 21.3 - Prob. 38PCh. 21.3 - Prob. 39PCh. 21.3 - Prob. 40PCh. 21.4 - Derive the scalar form of the rotational equation...Ch. 21.4 - Prob. 42PCh. 21.4 - Prob. 43PCh. 21.4 - Prob. 44PCh. 21.4 - The disk has a weight of 15 lb. Neglect the weight...Ch. 21.4 - Prob. 46PCh. 21.4 - Prob. 47PCh. 21.4 - Prob. 48PCh. 21.4 - Prob. 49PCh. 21.4 - Prob. 50PCh. 21.4 - Prob. 51PCh. 21.4 - The 5-kg circular disk is mounted off center on a...Ch. 21.4 - Prob. 53PCh. 21.4 - Prob. 54PCh. 21.4 - Prob. 55PCh. 21.4 - The 4-kg slender rod AB is pinned at A and held at...Ch. 21.4 - Prob. 57PCh. 21.4 - Prob. 58PCh. 21.4 - Prob. 59PCh. 21.4 - Show that the angular velocity of a body, in terms...Ch. 21.4 - Prob. 61PCh. 21.6 - The gyroscope consists of a uniform 450-g disk D...Ch. 21.6 - Prob. 63PCh. 21.6 - Prob. 64PCh. 21.6 - Prob. 65PCh. 21.6 - When viewed from the front of the airplane, the...Ch. 21.6 - Prob. 67PCh. 21.6 - Prob. 68PCh. 21.6 - Prob. 69PCh. 21.6 - Prob. 70PCh. 21.6 - Prob. 71PCh. 21.6 - Prob. 72PCh. 21.6 - Prob. 73PCh. 21.6 - Prob. 74PCh. 21.6 - Prob. 75PCh. 21.6 - Prob. 76PCh. 21.6 - Prob. 77PCh. 21.6 - Prob. 78P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The 214-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 94 N•m, it starts rolling from rest. Determine the average friction force that the ground applies to the wheel if it has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s². M Your Answer: Answer unitsarrow_forwardThe 30-kg wheel is rolling under the constant moment of M = 99 N-m. The wheel has radius r= 0.45 m, has mass center at point G, and the radius of gyration is kg = 0.23 m. The coefficients of friction between the wheel and the ground is ls = 0.40 and Hk; = 0.12. If the wheel rolls without slipping, determine the necessary static frictional force between the wheel and the ground. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. Take g = 9.81 m/s?. Marrow_forward6. The uniform ring of mass m = 10 kg and radius r= 0.5 m is hinged at O and can rotate freely in the vertical plane. If the ring is released with a clockwise angular velocity o = 4 rad/s from the position shown where OC is horizontal, determine the magnitude of the reaction at pin O the instant the disk is released. toarrow_forward
- A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 640 kg and an average gear-tooth force of 2.55 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 150 mm, R= 630 mm, 0 = 15% Detail of contact at B Answer: x= i B 14 ! mmarrow_forwardA large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 750 kg and an average gear-tooth force of 2.65 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 155 mm, R = 660 mm, 0 = 20° Detail of contact at B Answer: x = i B R →→→ G mmarrow_forwardThe 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.arrow_forward
- A single-cylinder reciprocating engine has a reciprocating mass of 6 kg. the crank rotates at 60 rpm and the stroke is 32 mm the mass of the revolving parts at 16 mm radius is 4 kg, if two-thirds of the reciprocating parts and the whole of the revolving parts are to be balanced. Determine the balance mass required at a radius of 35 mm and unbalanced force when the crank has turned 50° from the TDC. d luokarrow_forwardThe 186-kg wheel has a radius of gyration about its center O of ko = 300 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 92 N.m, it starts rolling from rest. Determine the average friction force that the ground applies to the wheel if it has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s². M Your Answer: units Answerarrow_forwardProblem 2: Rod AB has a mass of 10-kg and a uniform cross-sectional area. The piston has a mass of 15-kg. If the flywheel rotates at a constant angular velocity of 500 rev/min, determine the forces on A and B when 8 = 60°. Use a Vector Approach, show all your work. 150 mm, 750mmarrow_forward
- A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 780 kg and an average gear-tooth force of 2.20 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset T of the center of mass Gof the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 140 mm, R = 680 mm, 0 = 18°. Detail of contact at B B •G Answer:T= mmarrow_forwardDetermine the reactions at the pin support and the applied moment if the bar of figure (shown below) has a mass of 50 g. If θ is 15° and the angular acceleration is 20 rad/s².arrow_forwardA large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 790 kg and an average gear-tooth force of 2.25 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset T of the center of mass Gof the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 160 mm, R = 675 mm, 0 = 23°. Detail of contact at B B A- R Answer:I = 196 mmarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License