PEARSON ETEXT ENGINEERING MECH & STATS
15th Edition
ISBN: 9780137514724
Author: HIBBELER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 63P
The system consists of 60-lb and 20-lb blocks A and B , respectively, and 5-lb pulleys C and D that can be treated as thin disks Determine the speed of block A after block B has risen 5 ft, starting from rest. Assume that the cord does not slip on the pulleys, and neglect the mass of the cord.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The two blocks are released from rest when r= 0.8 m and 0= 30°. Neglecting the mass of the pulley and the effect of friction in the pulley and between block A and the horizontal surface, determine (a) the initial tension in the cable, (b) the initial acceleration of block A, (c) the initial acceleration of block B.
2) If the system is released from rest, determine the speeds of both masses after B has
moved 1 m. Neglect friction and the masses of the pulleys.
40 kg
20°
8 kg
As shown in the figure, the 300-lb counterweight B pulls the 200-lb block A up the 30° incline; the coefficient of kinetic friction is 0.20. If the pulleys are considered frictionless and weightless, determine the velocity of block A after it has moved 20 ft, starting from rest.
Chapter 18 Solutions
PEARSON ETEXT ENGINEERING MECH & STATS
Ch. 18 - The 80-kg wheel has a radius of gyration about its...Ch. 18 - The uniform 50-lb slender rod is subjected to a...Ch. 18 - The uniform 50-kg slender rod is at rest m the...Ch. 18 - The 50-kg wheel is subjected to a force of 50 N....Ch. 18 - If the uniform 30-kg slender rod starts from rest...Ch. 18 - The 20-kg wheel has a radius of gyration about its...Ch. 18 - At a given instant the body of mass m has an...Ch. 18 - A force of P = 20 N is applied to the cable, which...Ch. 18 - A force of P = 20 N is applied to the cable, which...Ch. 18 - The double pulley consists of two parts that are...
Ch. 18 - The double pulley cons1sts of two parts that are...Ch. 18 - Prob. 9PCh. 18 - The 10-kg uniform slender rod is suspended at rest...Ch. 18 - Prob. 14PCh. 18 - The pendulum consists of a 10-kg uniform disk and...Ch. 18 - The center O of the thin ring of mass m is given...Ch. 18 - Prob. 18PCh. 18 - Prob. 19PCh. 18 - Prob. 22PCh. 18 - Prob. 23PCh. 18 - Prob. 27PCh. 18 - The 10-kg rod AB is pin connected at A and...Ch. 18 - Motor M exerts a constant force of P = 750 Non the...Ch. 18 - The two 2-kg gears A and B are attached to the...Ch. 18 - F187. If the 30-kg disk is released from rest when...Ch. 18 - The 50-kg reel has a radius of gyration about its...Ch. 18 - The 60-kg rod OA is released from rest when = 0....Ch. 18 - Prob. 10FPCh. 18 - The 30-kg rod is released from rest when = 45....Ch. 18 - Prob. 12FPCh. 18 - Prob. 36PCh. 18 - Prob. 37PCh. 18 - The 40-kg wheel has a radius of gyration about its...Ch. 18 - The assembly consists of two 10-kg bars which are...Ch. 18 - The assembly consists of two 10-kg bars which are...Ch. 18 - Prob. 51PCh. 18 - Prob. 52PCh. 18 - If the 250-lb block is released from rest when the...Ch. 18 - The slender 15-kg bar is initially at rest and...Ch. 18 - The 50-lb wheel has a radius of gyration about its...Ch. 18 - The system consists of 60-lb and 20-lb blocks A...Ch. 18 - The pendulum of the Charpy impact machine has a...Ch. 18 - Prob. 2RPCh. 18 - The drum has a mass of 50 kg and a radius of...Ch. 18 - The spool has a mass of 60 Kg and a radius of...Ch. 18 - Prob. 5RPCh. 18 - At the Instant shown, the 50-lb bar rotates...Ch. 18 - Prob. 7RPCh. 18 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The system consists of 60lb and 20 lb blocks A and B, respectively, and 5-lb pulleys C and D that can be treated as thin disks. Determine the speed of block A after block B has risen 5ft, starting from rest. Assume that the cord does not slip on the pulleys, and neglect the mass of the cord. 0.5 ft D 0.5 ftarrow_forwardTwo boxes A and B, each having a weight of 160 Ib, sit on the 500-lb conveyor which is free to roll on the ground. If the belt starts from rest and begins to run with a speed of 3 ftls, determine the final speed of the conveyor if (a) the boxes are not stacked and A falls off then B falls off, and (b) A is stacked on top of B and both fall off together.arrow_forward2. Crates A and B weigh 100 lb and 50 lb, respectively. If they start from rest, determine their speed when t = 5 s. Also, find the force exerted by crate A on crate B during the motion. The coefficient of kinetic friction between the crates and the ground is = 0.25. A P = 50 lb Barrow_forward
- 3. The 60-lb boy swings down as shown in Fig. below. If he starts from rest when 0 = 0°, determine the rate of change in his speed and the tension on each of the two cords of the swing when 0 = 60°. Neglect his size and the mass of seat and cords for the calculation. His speed is actually the speed of boy's center of mass G.arrow_forwardThe baggage truck A shown in the photo below has a weight of 900 lb and tows a 550-lb cart B and 325lb cart C. For a short time the driving frictional force developed at the wheels of the truck is 40t lb,where t is in seconds. If the truck starts from rest, determine its speed in 2 seconds. Also, what is thehorizontal force acting on the coupling between the truck and the cart B at this instant?arrow_forwardThe double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinningarrow_forward
- Block A has a weight of 60 lb and block B has a weight of 10 lb. Neglect friction and the mass of the cord and pulleys. (Figure 1) Determine the speed of block A after it moves 4.5 ft down the plane, starting from rest.arrow_forward5. Determine the velocity of each block 2 seconds after the blocks are released from rest. Neglect the mass of the pulleys and cord (hint: there are three unknowns). A 10 lb B 50 lbarrow_forwardThe straight tube slide in an in-door playground has a 30o angle with the ground as shown. The 30 kg kid slides down the slide from rest. Determine the speed of the kid when they just reach the bottom of the slide at B using the method of Work and Energy or Conservation of Energy. Assume the coefficient of kinetic friction between the slide and the kid is 0.2.arrow_forward
- A constant force of F acts on a mass as shown. The mass starts its motion from rest at position 1, the unstretched lenght of the spring is 250 mm, and the spring modulus is k = 1.5 kN/m. Neglecting the friction, determine the required force F to cause the 2 - kg mass to have a speed of v2 = 1.5 m/s at position 2.arrow_forwardTwo blocks namely Blocks A and B weigh 25 lb and 50 lb, respectively. The blocks are at rest and the spring (k = 25 lb/ft) is unstretched when the blocks are in the position shown in the picture. Determinea. The speed of block B when it is 1 ft below its initial position.b. The maximum distance that block B will droparrow_forwardTwo blocks are joined by an inextensible cable as shown. If the system is released from rest, determine the velocity of block A after it has moved 2m. Assume that the coefficient of kinetic friction between block A and the plane is μk = 0.25 and that the pulley is weightless and frictionless.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Ch 2 - 2.2.2 Forced Undamped Oscillation; Author: Benjamin Drew;https://www.youtube.com/watch?v=6Tb7Rx-bCWE;License: Standard youtube license