PEARSON ETEXT ENGINEERING MECH & STATS
15th Edition
ISBN: 9780137514724
Author: HIBBELER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 7P
The double pulley consists of two parts that are attached to one another. It has a weight of 50 lb and a centroidal radius of gyration of ko = 0.6 ft and 1s turning with an angular velocity of 20 rad/ s clockwise. Determine the kinetic energy of the system. Assume that neither cable slips on the pulley.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The 21-kg wheel has a radius of gyration about its center O of ko =260 mm, and
radius r = 0.5 m. When the wheel is subjected to the constant force F = 247 N,
applied to the wheel's center axle at an angle = 6°, it starts rolling from rest.
Determine the wheel's angular velocity W (in rad/s) after 4.0 seconds if the wheel
has been rolling without slipping. Please pay attention: the numbers may change
since they are randomized. Your answer must include 1 place after the decimal point.
Take g = 9.81 m/s².
Your Answer:
G
Answer
r
0
F
1. The 20-kg flywheel has a radius of gyration kg = 0.5 m about the axis of
its attached shaft (O-0). It is at rest when subjected to a torque that rises
uniformly from 0 to 2 N-m over 3 revolutions, then holds at a constant 2
N-m for the remainder of the motion. What is the angular velocity of the
flywheel after 10 revolutions? Give your answer in RPM.
The 250-kg wheel has a radius of gyration about its center O of ko = 260 mm, and
radius r = 0.4 m. When the wheel is subjected to the constant couple moment M =
64 N.m, it starts rolling from rest. Determine the total angular impulse L (in N.m.s)
about the wheel's IC after 7.3 seconds if the wheel has been rolling without slipping.
Please pay attention: the numbers may change since they are randomized. Your
answer must include 1 place after the decimal point. Take g = 9.81 m/s².
M
Your Answer:
Answer
Chapter 18 Solutions
PEARSON ETEXT ENGINEERING MECH & STATS
Ch. 18 - The 80-kg wheel has a radius of gyration about its...Ch. 18 - The uniform 50-lb slender rod is subjected to a...Ch. 18 - The uniform 50-kg slender rod is at rest m the...Ch. 18 - The 50-kg wheel is subjected to a force of 50 N....Ch. 18 - If the uniform 30-kg slender rod starts from rest...Ch. 18 - The 20-kg wheel has a radius of gyration about its...Ch. 18 - At a given instant the body of mass m has an...Ch. 18 - A force of P = 20 N is applied to the cable, which...Ch. 18 - A force of P = 20 N is applied to the cable, which...Ch. 18 - The double pulley consists of two parts that are...
Ch. 18 - The double pulley cons1sts of two parts that are...Ch. 18 - Prob. 9PCh. 18 - The 10-kg uniform slender rod is suspended at rest...Ch. 18 - Prob. 14PCh. 18 - The pendulum consists of a 10-kg uniform disk and...Ch. 18 - The center O of the thin ring of mass m is given...Ch. 18 - Prob. 18PCh. 18 - Prob. 19PCh. 18 - Prob. 22PCh. 18 - Prob. 23PCh. 18 - Prob. 27PCh. 18 - The 10-kg rod AB is pin connected at A and...Ch. 18 - Motor M exerts a constant force of P = 750 Non the...Ch. 18 - The two 2-kg gears A and B are attached to the...Ch. 18 - F187. If the 30-kg disk is released from rest when...Ch. 18 - The 50-kg reel has a radius of gyration about its...Ch. 18 - The 60-kg rod OA is released from rest when = 0....Ch. 18 - Prob. 10FPCh. 18 - The 30-kg rod is released from rest when = 45....Ch. 18 - Prob. 12FPCh. 18 - Prob. 36PCh. 18 - Prob. 37PCh. 18 - The 40-kg wheel has a radius of gyration about its...Ch. 18 - The assembly consists of two 10-kg bars which are...Ch. 18 - The assembly consists of two 10-kg bars which are...Ch. 18 - Prob. 51PCh. 18 - Prob. 52PCh. 18 - If the 250-lb block is released from rest when the...Ch. 18 - The slender 15-kg bar is initially at rest and...Ch. 18 - The 50-lb wheel has a radius of gyration about its...Ch. 18 - The system consists of 60-lb and 20-lb blocks A...Ch. 18 - The pendulum of the Charpy impact machine has a...Ch. 18 - Prob. 2RPCh. 18 - The drum has a mass of 50 kg and a radius of...Ch. 18 - The spool has a mass of 60 Kg and a radius of...Ch. 18 - Prob. 5RPCh. 18 - At the Instant shown, the 50-lb bar rotates...Ch. 18 - Prob. 7RPCh. 18 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The 30-kg wheel has a radius of gyration about its center O of ko = 240 mm, and radius r = 0.5 m. When the wheel is subjected to the constant force F = 388 N, applied to the wheel's center axle at an angle = 6°, it starts rolling from rest. Determine the total angular impulse L (in N•m.s) about the wheel's IC after 3.7 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². Your Answer: G Answer Ө Farrow_forwardThe 213-kg wheel has a radius of gyration about its center O of ko = 240 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 85 N·m, it starts rolling from rest. Determine the wheel's angular velocity W (in rad/s) after 4.4 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answerarrow_forwardThe double pulley consists of two parts that are attached to one another. It has a mass of 20 kg and a radius of gyration about its center of ko= 200 mm and is turning with an angular velocity of 15 rad/s clockwise. Determine the kinetic energy of the system. Assume that neither cable slips on the pulley.arrow_forward
- THE WEIGHT OF THE UNBALANCED WHEEL IS 200 KG AND IT HS A RADIUS OF GYRATION ABOUT ITS MASS CENTER, G, OF 0.3 METERS. AT THE INSTANT SHOWN IT IS ROTATING AT 6 RAD/SIN A CLOCKWISE DIRECTION. FIND THE FORCES BETWEEN AT THE PIVOT POINT C. Please include a Free Body Diagramarrow_forwardThe rod AB is non-uniform with a radius of gyration of 4.00 ft with respect to a horizontal axis through the center of mass G. It weighs 161 lb. At the moment shown the rod has a counterclockwise angular velocity of 3.00 rad/sec, and the spring is compressed by 2.00 ft. Calculate the force constant of the spring that will reduce the angular velocity of the rod to 1.50 rad/sec when it reaches the horizontal position. Assume the blocks A and B are weightless.arrow_forwardThe center of the 173-lb wheel with centroidal radius of gyration of 5.6 in. has a velocity of 3.4 ft/sec down the incline in the position shown. Calculate the normal reaction N under the wheel as it rolls past position A. Assume that no slipping occurs. 36° 24" 17" Aj Answer: N = i Ibarrow_forward
- The concrete block weighing 644 lb is elevated by the hoisting mech- anism shown, where the cables are securely wrapped around the re- spective drums. The drums, which are fastened together and turn as a single unit about their mass center at 0, have a combined weight of 322 lb and a radius of gyration about O of 18 in. If a constant tension P = 400 lb is maintained by the power unit at A, determine the vertical acceleration of the block and the resultant force on the bearing at O. Solve using; 24" 12" P = 400 lb (a) Two free body diagrams for concrete block and drum. W = 322 lb ko = 18" (b) One system block diagram ( concrete block and drum as one system). 45° A 644 lbarrow_forwardThe 20-kg wheel has a radius of gyration about its center O of ko = 280 mm, and radius r = 0.5 m. When the wheel is subjected to the constant force F= 388 N, applied to the wheel's center axle at an angle = 11°, it starts rolling from rest. Determine the total angular impulse L (in N.m.s) about the wheel's /C after 5.5 seconds if the wheel has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². F Ө Your Answer: Answerarrow_forwardEach of the two links has a mass of 1.5 kg and a centroidal radius of gyration of 55 mm. The slider at B has a mass of 3.4 kg and moves freely in the vertical guide. The spring has a stiffness of 5.9 kN/m. If a constant torque M = 14.0 N-m is applied to link OA through its shaft at O starting from the rest position at = 45°, determine the angular velocity of OA when 0 = 0. 40 mm 330 mm O Answer: w= i 165 mm 165 mm rad/sarrow_forward
- The 24-kg wheel has a radius of gyration about its center O of ko = 260 mm, and radius r= 0.4 m. When the wheel is subjected to the couple moment M = 90 N•m, it slips as it rolls. Determine the linear acceleration of the wheel's center O (in m/s?). The coefficient of kinetic friction between the wheel and the plane is Uk = 0.45. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. Marrow_forward3. The wheel has a mass of 100 kg and a radius of gyration about the z-axis of k: = 300 mm rests on a smooth horizontal plane. If the belt is subjected to a force of P= 170 N, determine the angular velocity of the wheel and the speed of its center of mass two seconds after the 400 mm force is applied.arrow_forwardEach of the two links has a mass of 2 kg and a centroidal radius of gyration of 60mm. The slider at B has a mass of 3 kg and moves freely in the vertical guide. The springhas a stiffness of 6 kN/m. If a constant torque M = 20 N∙m is applied to link OA throughits shaft at O starting from the rest position at θ = 45°, determine the angular velocity ofOA when θ = 0.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License