Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 18, Problem 4ASRQ
Technician A says that a starter no-load test is conducted with the starter in a bench vise. Technician B says that the no-load test is used to determine starter motor circuit voltage drop. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A starter cranks, but cranks slowly. The shop performs a voltage drop on the ground and power side of the starter circuit and they both test good. Technician A says the battery may be bad. Technician B says the starter may be bad. Who is correct?
Is the car clutch failed due to static load or cyclic load?
Technician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct?
Chapter 18 Solutions
Automotive Technology
Ch. 18 - Prob. 1SACh. 18 - Prob. 2SACh. 18 - The part of the armature that the brushes ride on...Ch. 18 - Describe how to perform a starter bench test.Ch. 18 - True or False? The strength of the magnetic field...Ch. 18 - True or False? Worn armature bearings can result...Ch. 18 - Which of the following is not part of the starter...Ch. 18 - Which of the following tests would not be...Ch. 18 - When the starter spins but does not crank the...Ch. 18 - If the solenoid clicks while trying to crank the...
Ch. 18 - Prob. 5MCCh. 18 - Prob. 6MCCh. 18 - Prob. 7MCCh. 18 - The device that prevents the engine from turning...Ch. 18 - A control circuit voltage drop test shows a 1.1...Ch. 18 - An engine cranks slowly: Technician A says that a...Ch. 18 - Prob. 2ASRQCh. 18 - Pinion gear-to-flywheel ring gear clearance is...Ch. 18 - Technician A says that a starter no-load test is...Ch. 18 - Cranking current is excessive but is normal when...Ch. 18 - Prob. 6ASRQCh. 18 - When diagnosing a no-crank no-start condition, no...Ch. 18 - While discussing a no-crank condition: Technician...Ch. 18 - Prob. 9ASRQCh. 18 - While discussing electric motors: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing a no-crank condition: Technician A says to verify the condition of the batten' before testing the starter motor Technician B says a scan tool may be used to check starter control circuit operation. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen diagnosing a no-crank no-start condition, no voltage is present at the S terminal of the solenoid while attempting to crank the engine. Technician A says a faulty starter motor is the cause. Technician B says a shorted safety switch is the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A checks a starters field coils for opens by connecting an ohmmeter between the coils' power feed wire and the field coil brush lead. Technician B checks a starters field coil for a short to ground by connecting an ohmmeter across the field coil brush lead and the starter housing. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- If the solenoid clicks while trying to crank the engine with the starter, which of the following is not a probable cause? A faulty neutral safety switch Low battery voltage Low voltage available to the solenoid An open in the hold-in windingarrow_forwardDescribe how to perform a starter bench test.arrow_forwardAn engine cranks slowly: Technician A says that a possible cause of the problem is poor starter circuit connections. Technician B says that an engine problem could be the cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- When the starter spins but does not crank the engine, which of the following may be true? Defective starter relay Damaged flywheel teeth A faulty starter solenoid All of the abovearrow_forwardCranking current is excessive but is normal when the starter is bench tested: Technician A says the problem could be with the positive battery connection to the solenoid. Technician B says there could be an engine mechanical problem. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhile discussing AWD systems: Technician A says that some systems are electronically controlled and use an electromagnetic clutch to engage and disengage the drive axles. Technician B says that some cars do not use a transfer case, but they are equipped with a third differential unit. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- A control circuit voltage drop test shows a 1.1 volt drop at the starter S terminal. Which of the following could be the cause? High resistance in the solenoid switch circuit High resistance in the clutch safety switch Loose battery cable connection Short in the starter armature windingsarrow_forwardTechnician A says that if a drive belt does not have the proper tension, it may produce squealing and chirping noises. Technician B says belt tension should be checked even if the engine has an automatic belt tensioner. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing IAC motor removal, service, and replacement: Technician A says that throttle body cleaner may be used to clean the IAC motor internal components. Technician B says that on some vehicles, IAC motor damage occurs if the pintle is extended more than specified during installation. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License