University Physics (14th Edition)
14th Edition
ISBN: 9780133969290
Author: Hugh D. Young, Roger A. Freedman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 15, Problem 15.59P
CP A 1.80-m-long uniform bar that weighs 638 N is suspended in a horizontal position by two vertical wires that are attached to the ceiling. One wire is aluminum and the other is copper. The aluminum wire is attached to the left-hand end of the bar, and the copper wire is attached 0.40 m to the left of the right-hand end. Each wire has length 0.600 in and a circular cross section with radius 0.280 mm. What is the fundamental frequency of transverse standing waves for each wire?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Two wires of equal cross- section one
made up of aluminium and other of brass are
joined end to end. When the combination at
wire is kept under tension the elongation in
wires are found to be equal. Find the ratio of
lengths of two wires. (Y, = 7 x 10º N/m² and
%3D
AL
Y = 9.1 x 101º N/m²).
%3D
A 1.80-m-long uniform bar that weighs 638 N is suspended in a horizontal position by two vertical wires that are attached to the ceiling. One wire is aluminum and the other is copper. The aluminum wire is attached to the left-hand end of the bar, and the copper wire is attached 0.40 m to the left of the right-hand end. Each wire has length 0.600 m and a circular cross section with radius 0.280 mm. What is the fundamental frequency of transverse standing waves for each wire?
A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long. Those at each end are of copper and the middle one is of iron. Determine the ratios of their diameters if each is to have the same tension.
Chapter 15 Solutions
University Physics (14th Edition)
Ch. 15 - Two waves travel on the same string. Is it...Ch. 15 - Under a tension F, it takes 2.00 s for a pulse to...Ch. 15 - What kinds of energy are associated with waves on...Ch. 15 - The amplitude of a wave decreases gradually as the...Ch. 15 - Prob. Q15.5DQCh. 15 - The speed of ocean waves depends on the depth of...Ch. 15 - Is it possible to have a longitudinal wave on a...Ch. 15 - For transverse waves on a string, is the wave...Ch. 15 - The four strings on a violin have different...Ch. 15 - Prob. Q15.10DQ
Ch. 15 - Prob. Q15.11DQCh. 15 - Prob. Q15.12DQCh. 15 - In a transverse wave on a string, the motion of...Ch. 15 - Energy can be transferred along a string by wave...Ch. 15 - Prob. Q15.15DQCh. 15 - If you stretch a rubber band and pluck it, you...Ch. 15 - A musical interval of an octave corresponds to a...Ch. 15 - By touching a string lightly at its center while...Ch. 15 - Prob. Q15.19DQCh. 15 - Violins are short instruments, while cellos and...Ch. 15 - What is the purpose of the frets on a guitar? In...Ch. 15 - The speed of sound in air at 20C is 344 m/s. (a)...Ch. 15 - BIO Audible Sound. Provided the amplitude is...Ch. 15 - Prob. 15.3ECh. 15 - BIO Ultrasound Imaging. Sound having frequencies...Ch. 15 - Prob. 15.5ECh. 15 - A fisherman notices that his boat is moving up and...Ch. 15 - Transverse waves on a siring have wave speed 8.00...Ch. 15 - Prob. 15.8ECh. 15 - Prob. 15.9ECh. 15 - A water wave traveling in a straight line on a...Ch. 15 - A sinusoidal wave is propagating along a stretched...Ch. 15 - CALC Speed of Propagation vs. Particle Speed. (a)...Ch. 15 - A transverse wave on a string has amplitude 0.300...Ch. 15 - Prob. 15.14ECh. 15 - One end of a horizontal rope is attached to a...Ch. 15 - With what tension must a rope with length 2.50 m...Ch. 15 - Prob. 15.17ECh. 15 - A 1.50-m string of weight 0.0125 N is tied to the...Ch. 15 - A thin, 75.0-cm wire has a mass of 16.5 g. One end...Ch. 15 - A heavy rope 6.00 m long and weighing 29.4 N is...Ch. 15 - A simple harmonic oscillator at the point x = 0...Ch. 15 - A piano wire with mass 3.00 g and length 80.0 cm...Ch. 15 - Prob. 15.23ECh. 15 - Prob. 15.24ECh. 15 - A jet plane at takeoff can produce sound of...Ch. 15 - Threshold of Pain. You are investigating the...Ch. 15 - Energy Output. By measurement you determine that...Ch. 15 - A fellow student with a mathematical bent tells...Ch. 15 - At a distance of 7.00 1012 m from a star, the...Ch. 15 - Reflection. A wave pulse on a siring has the...Ch. 15 - Reflection. A wave pulse on a string has the...Ch. 15 - Reflection. A wave pulse on a string has the...Ch. 15 - Suppose that the left-traveling pulse in Exercise...Ch. 15 - Two pulses are moving in opposite directions at...Ch. 15 - Interference of Rectangular Pulses. Figure E15.35...Ch. 15 - CALC Adjacent antinodes of a standing wave on a...Ch. 15 - Prob. 15.37ECh. 15 - Prob. 15.38ECh. 15 - A wire with mass 40.0 g is stretched so that its...Ch. 15 - A piano tuner stretches a steel piano wire with a...Ch. 15 - CALC A thin, taut string tied at both ends and...Ch. 15 - Prob. 15.42ECh. 15 - Prob. 15.43ECh. 15 - Prob. 15.44ECh. 15 - Prob. 15.45ECh. 15 - Prob. 15.46ECh. 15 - Guitar String. One of the 63.5-cm-long strings of...Ch. 15 - A transverse wave on a rope is given by...Ch. 15 - CALC A transverse sine wave with an amplitude of...Ch. 15 - CP A 1750-N irregular beam is hanging horizontally...Ch. 15 - Three pieces of string, each of length L, are...Ch. 15 - Weightless Ant. An ant with mass m is standing...Ch. 15 - You must determine the length of a long, thin wire...Ch. 15 - Music. You are designing a two-string instrument...Ch. 15 - CP A 5.00-m, 0.732-kg wire is used to support two...Ch. 15 - A uniform, 8.40-kg, spherical shell 50.0 cm in...Ch. 15 - For a string stretched between two supports, two...Ch. 15 - A 0.800-m-long string with linear mass density =...Ch. 15 - CP A 1.80-m-long uniform bar that weighs 638 N is...Ch. 15 - A continuous succession of sinusoidal wave pulses...Ch. 15 - A horizontal wire is tied to supports at each end...Ch. 15 - CP A vertical, 1.20-m length of 18-gauge (diameter...Ch. 15 - A sinusoidal transverse wave travels on a string....Ch. 15 - A vibrating string 50.0 cm long is under a tension...Ch. 15 - Clothesline Nodes. Cousin Throckmorton is once...Ch. 15 - A strong string of mass 3.00 g and length 2.20 m...Ch. 15 - A thin string 2.50 m in length is stretched with a...Ch. 15 - CALC A guitar string is vibrating in its...Ch. 15 - A uniform cylindrical steel wire, 55.0 cm long and...Ch. 15 - A string with both ends held fixed is vibrating in...Ch. 15 - CP A large rock that weighs 164.0 N is suspended...Ch. 15 - Holding Up Under Stress. A string or rope will...Ch. 15 - Tuning an Instrument. A musician tunes the...Ch. 15 - Prob. 15.74PCh. 15 - DATA In your physics lab, an oscillator is...Ch. 15 - DATA You are measuring the frequency dependence of...Ch. 15 - CP CALC A deep-sea diver is suspended beneath the...Ch. 15 - BIO WAVES ON VOCAL FOLDS. In the larynx, sound is...Ch. 15 - BIO WAVES ON VOCAL FOLDS. In the larynx, sound is...Ch. 15 - BIO WAVES ON VOCAL FOLDS. In the larynx, sound is...
Additional Science Textbook Solutions
Find more solutions based on key concepts
12. (I) Write the following as full (decimal) numbers without prefixes on the units: (a) 286.6mm, (b) 85µV, (c)...
Physics: Principles with Applications
5. A position vector with magnitude 10 m points to the right and up. Its x-component is 6.0 m. What is the valu...
College Physics: A Strategic Approach (3rd Edition)
What is the volume of one mole of air, at room temperature and 1 atm pressure?
An Introduction to Thermal Physics
How does radioactivity allow archeologists to measure the age of ancient artifacts?
Conceptual Integrated Science
7. Block B in FIGURE EX7.7 rests on a surface for which the static and kinetic coefficients of friction are 0.6...
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- Figure P12.38 shows a light truss formed from three struts lying in a plane and joined by three smooth hinge pins at their ends. The truss supports a downward force of F=1000N applied at the point B. The truss has negligible weight. The piers at A and C are smooth. (a) Given 1 = 30.0 and 2 = 45.0, find nA and nC. (b) One can show that the force any strut exerts on a pin must be directed along the length of the strut as a force of tension or compression. Use that fact to identify the directions of the forces that the struts exert on the pins joining them. Find the force of tension or of compression in each of the three bars. Figure P12.38arrow_forwardA copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57arrow_forwardWhy is the following situation impossible? A worker in a factory pulls a cabinet across the floor using a rope as shown in Figure P12.36a. The rope make an angle = 37.0 with the floor and is tied h1 = 10.0 cm from the bottom of the cabinet. The uniform rectangular cabinet has height = 100 cm and width w = 60.0 cm, and it weighs 400 N. The cabinet slides with constant speed when a force F = 300 N is applied through the rope. The worker tires of walking backward. He fastens the rope to a point on the cabinet h2 = 65.0 cm off the floor and lays the rope over his shoulder so that he can walk forward and pull as shown in Figure P12.36b. In this way, the rope again makes an angle of = 37.0 with the horizontal and again has a tension of 300 N. Using this technique, the worker is able to slide the cabinet over a long distance on the floor without tiring. Figure P12.36 Problems 36 and 44.arrow_forward
- A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81arrow_forwardIn the short story The Pit and the Pendulum by 19th-century American horror writer Edgar Allen Poe, a man is tied to a table directly below a swinging pendulum that is slowly lowered toward him. The bob of the pendulum is a 1-ft steel scythe connected to a 30-ft brass rod. When the man first sees the pendulum, the pivot is roughly 1 ft above the scythe so that a 29-ft length of the brass rod oscillates above the pivot (Fig. P16.39A). The man escapes when the pivot is near the end of the brass rod (Fig. P16.39B). a. Model the pendulum as a particle of mass ms 5 2 kg attached to a rod of mass mr 5 160 kg. Find the pendulums center of mass and rotational inertia around an axis through its center of mass. (Check your answers by finding the center of mass and rotational inertia of just the brass rod.) b. What is the initial period of the pendulum? c. The man saves himself by smearing food on his ropes so that rats chew through them. He does so when he has no more than 12 cycles before the pendulum will make contact with him. How much time does it take the rats to chew through the ropes? FIGURE P16.39arrow_forwardWhen a circus performer performing on the rings executes the iron cross, he maintains the position at rest shown in Figure P12.37a. In this maneuver, the gymnasts feet (not shown) are off the floor. The primary muscles involved in supporting this position are the latissimus dorsi (lats) and the pectoralis major (pecs). One of the rings exerts an upward force Fk on a hand as show n in Figure P12.37b. The force Fs, is exerted by the shoulder joint on the arm. The latissimus dorsi and pectoralis major muscles exert a total force Fm on the arm. (a) Using the information in the figure, find the magnitude of the force Fm for an athlete of weight 750 N. (b) Suppose a performer in training cannot perform the iron cross but can hold a position similar to the figure in which the arms make a 45 angle with the horizontal rather than being horizontal. Why is this position easier for the performer? Figure P12.37arrow_forward
- A spring 1.50 m long with force constant 475 N/m is hung from the ceiling of an elevator, and a block of mass 10.0 kg is attached to the bottom of the spring. (a) By how much is the spring stretched when the block is slowly lowered to its equilibrium point? (b) If the elevator subsequently accelerates upward at 2.00 m/s2, what is the position of the block, taking the equilibrium position found in part (a) as y = 0 and upwards as the positive y-direction. (c) If the elevator cable snaps during the acceleration, describe the subsequent motion of the block relative to the freely falling elevator. What is the amplitude of its motion?arrow_forwardThe leg bone (femur) breaks under a compressive force of about 8.20 × 104 N for a human and 11.7 × 104 N for a horse. The human femur has a compressive strength of 160 MPa, whereas the horse femur has a compressive strength of 140 MPa. What is the effective cross-sectional area of the femur in a human? (Note: Since the center of the femur contains bone marrow, which has essentially no compressive strength, the effective cross-sectional area is about 80% of the total cross-sectional area.)arrow_forwardThe steel system consists of rod CD, rod AB and a rigid bar AC. The diameter of rods CD and AB are 16 mm and 18 mm, 2.0 m T respectively. If a force of 30 kN is applied to point E, determine: a) the normal stress in rod AB and DC, b) the horizontal displacement of point E. Est = 200 GPa. 0.6 m E 0.3 m 30 kN B 4.0 m Aarrow_forward
- A solid copper cube has an edge length of 89.6 cm. How much stress must be applied to the cube to reduce the edge length to 89 cm? The bulk modulus of copper is 1.4 x 1011 N/m². Number i 27.94 Units N/m^2 or Paarrow_forwardA copper wire of length 3 m has a diameter 1 mm. If weight of 10 kg is attached to one end of wire, what is the extension produced? Calculate lateral contraction if poisson's ratio is 0.25 (Y=12.5 x 10¹⁰ N/m²)arrow_forward. A copper wire LM is fused at one end, M to an iron wire MN as shown in figure below. L M N F The copper wire has length 0.90 m and cross-section area 0.90 x10-6 m². The iron wire has length 1.40 m and cross-section area 1.30 x10-6 m2. The compound wire is stretched and the total length increases by 0.01 m. Given Yiron = 2.10 x1011 Pa and Give Ycopper = 1.30 x1011 Pa. Determine %3D %3! a. the ratio of the extension of copper wire to the extension of iron wire,arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY