A copper wire of length 3 m has a diameter 1 mm. If weight of 10 kg is attached to one end of wire, what is the extension produced? Calculate lateral contraction if poisson's ratio is 0.25 (Y-12.5 x 10¹⁰0 N/m²)
Q: 1. A mass is supported by the cable system shown below. If the tension in cable A is 14 kN, find the…
A: Tension in cable A: TA = 14 kN = 14000 N Cable attached to mass "m" composed of aluminium alloy:…
Q: A copper wire 4 m. long has diameter of 1 mm, if a load of 10 kg. wt is attached at other end. What…
A: Solution:-Given thatlength of wire (L)=4 mdiameter of wire (d)=1 mm=0.001 mmass of Load (m)=10…
Q: A thin rod extends from x =D 0 to x = 13.0 cm. It has a cross-sectional area A = 6.50 cm-. adits…
A:
Q: Find the minimum diameter of an | = 15.1 m long tungsten wire that will stretch no more than 7.00 mm…
A:
Q: What will be the density of sea water at a depth of 1 km, if the density at the surface is 1025…
A: Correct option : (d) 1029.387 kg/m3
Q: A metallic bar of cross-section Ao = 103 mm² and length Lo = 0.1 mm, is subjected to = 1600 N, the…
A: Given: The cross section area of the metallic bar is 103 mm2. The original length of the…
Q: The velocity distribution for the flow of oil (SAE 10W) at 38°C between two walls is given by V =…
A: V=100y0.1-y Shear stress is a type of stress that arises when a force is applied parallel to a…
Q: A small sphere with a mass of 0.1 grams, carrying a load of 3.10-10 C, is attached to the end of a 5…
A: Here, Mass(m)= 0.1gm
Q: The total cross-sectional area of the load-bearing calcified portion of the two forearm bones…
A: Given: Area, A = 2.4 cm2 initial velocity, u = 80 km/h = 22.22 m/s time, t = 5 ms = 0.005 s final…
Q: A 5.25-m-long steel rod must not stretch more than 2.48 mm and the normal stress must not exceed 181…
A:
Q: f a compressional stress of 200.0 N is applied to a copper rod having a diameter of .500 cm and a…
A:
Q: A cable hanging vertically under gravity must support its weight, w = mg, where m is the mass of the…
A: To avoid snapping of the cable, the tensile strength will be equal to the force per unit area. Write…
Q: Question 16: A cubical solid aluminium (bulk modulus = -V (dP/dV) = 70 GPa) block has an edge length…
A: Given that, Bulk modulus=-VdPdV=70 GPa Here we know that, B=VdPdV
Q: Q6 300 N 200 mm The acrylic plastic rod is 200 mm long and 15 mm in diameter. E, = 1.20 GPa, and v,…
A:
Q: Q. 29: A wire of length (L) and radius (r) is loaded with a weight (Mg). If (Y) and (o) denote the…
A:
Q: A 8-mm-thick rectangular alloy bar is subjected to a tensile load P by pins at A and B, as shown in…
A:
Q: Two wires of equal cross- section one made up of aluminium and other of brass are joined end to end.…
A: To find- Ratio of length of two wires L1L2=? Given- lAL=lbrass=l,MAL=Mbrass=MrAL=rbrass=rYAL=7×1010…
Q: : Two wires of equal cross-section one made up of aluminium and other of brass are joined end to…
A: We need to find- Ratio of lengths of two wires LAlLbrass=? The data given as-…
Q: copper wire of length 3 m nas a diameter 1 mm. If weight of 10 kg is attached to one end of wire,…
A: To find- (1) Extension produced (l)=? (2) Lateral contraction =? Given- Length of wire (L)=3 m…
Q: Two parallel and opposing forces of each value (4000N) act tangentially on opposite sides of a cube…
A: Given: Force F=4000 N Side length L=25 cm=25×10-2 m Shear modulus S=80 GPa=80×109 Pa
Q: A farmer making grape juice fills a glass bottle to the brim and caps it tightly. The juice expands…
A: thank you
Q: An object weighs 4.5 x 105 N is supported by steel cable, with cross-sectional area of 6.0 cm 2, the…
A: Given: The weight of the object is 4.5x105 N. The cross-sectional area is 6 cm2. Young's modulus of…
Q: 5-77. The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is subjected…
A: Diameter of steel shaft , d = 40mm The applied force, F= 3kN Rigidity modulus of the shaft, Gst =…
Q: A 1.05-m-long rod of negligible weight is supported at its ends by wires A and B of equal length…
A: This question involves two concepts: (A) Free body diagram and subsequent condition for the static…
Q: A copper wire 4 m long has diameter of 1 mm, if a load of 10 kg. wt is attached at other end. What…
A: We need to compute-(a) extension (l)=?(b) Lateral compression=?Given that-Length of wire (L)=4…
Q: Two exactly similar wires of steel (Y, = 20 x 10" dyne/cm²) and copper (Y, = 12 × 101 dyne/cm²) are…
A: To find- Elongation of copper wire (ec)=? Given- Ys=20×1011 dyne/cm2Yc=12×1011 dyne/cm2ec+es=1 cm
Q: The table below shows ultimate tensile strengths (Fu ) and Young's moduli (Y) for tungsten (W) and…
A:
Q: Ex1: produce an extension of 0.3 cm. If Poisson's ratio for copper is 0.26, what is the lateral…
A: To find-Lateral strain produced=?Given-Length of wire (L)=3 mElongation produced (l)=0.3 cm…
Q: If the Junk modulus of Y is 160GPA and the shear modulus of elasticity is 0.25Y, what is the value…
A:
Q: Young's modulus for compression of human bone is approximately 9x10⁹ N/m^2. Assume that a femur has…
A: Given in question : Young's modulus (Y) = 9 x 109 N/m2 Stress (S) = 7.5 x 107 N/m2 Length of the…
Q: To escape a burning buildingAmold has to jump from a third-story window that is about 10.0 m above…
A:
Q: Q.29: A wire of length (L) and radius (r) is loaded with a weight (Mg). If (Y) and (o) denote the…
A: We have L = length of wire r = radius of wire F = Mg = weight Y = youngs modulus
Q: The bulk modulus of K, modulus of elasticity E and Poisson's ratio is then which of m the following…
A: The relation between the bulk modulus(K), modulus of Elasticity(E) and the Poisson's ratio(ν) is…
Q: An underwater oil and gas piping system is going to be established through South China Sea…
A: The objective of the question is to determine the highest internal pressure that can be applied to…
Q: A steel wire of length 1.40 m and diameter 1.00 mm is joined to an aluminum wire of identical…
A: We are given the mass of object. We can thus find the force acting on wire. We then find the stress…
Q: Two wires A and B are of the same length. Their diameters are in the ratio 1:2 and the Young's…
A: We need to compute-Ratio of elongations produced eAeB=?The data given as-Length of wire A=Length of…
Q: A 4.5 long iron rod with a cross-sectional area of 0.75 centimeter square stretches 0.85 mm when a…
A: ∆LL=0.85×10-34.5=0.19×10-3 Force, F=mg=195×9.8=1911 N Where m is mass. Area, A=0.75 cm2=0.75×10-4 m2…
Q: A B C 300 μm Which denotes the apical meristem in roots? B C D A D
A: The correct answer is B.Explanation: The image you sent is a labelled diagram of the tip of a root,…
Q: A fishing rope of length (74+ 50) m has the diameter (74 + 5) mm. When a weight of (74 +200) N is…
A: i. The cross-sectional area of the rope is given by,
Q: For a brass alloy, the stress at which plastic deformation begins is 350 MPa, and the modulus of…
A: Solution: Given that Plastic strentgh = 350 MPa E = 103 GPa
Q: Steel construction beams, with an industry designation of "W12 x 25," have a weight of 25 pounds per…
A: Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…
Q: An oil specimen has an initial volume of 597 cm³ and is subjected to 3.6 MPa pressure increase. The…
A: Initial volume V=597 cm3 Rise in volume △V=0.35 cm3 Rise in pressure △P=3.6 MPa=3.6×106 Pa To find:…
Q: brass rod with a length of 1.40 m and a cross. sectional area of 2.00 square cm is fastened end to…
A: brass rod with a length of 1.40 m and a cross. sectional area of 2.00 square cm is fastened end to…
Q: For a bronze alloy, the stress at which plastic deformation begins is 295 MPa and the modulus of…
A:
Q: 4. A single axial load of P = 60 kN is attached at the end C of the brass rod ABC. Knowing that E =…
A:
Step by step
Solved in 2 steps