EBK THERMODYNAMICS: AN ENGINEERING APPR
EBK THERMODYNAMICS: AN ENGINEERING APPR
9th Edition
ISBN: 8220106796979
Author: CENGEL
Publisher: YUZU
bartleby

Videos

Question
Book Icon
Chapter 14.7, Problem 75P

(a)

To determine

The temperature and relative humidity of air when it leaves the heating section.

(a)

Expert Solution
Check Mark

Answer to Problem 75P

The temperature and relative humidity of air when it leaves the heating section is 19.5°Cand37.7% respectively.

Explanation of Solution

Express initial partial pressure.

Pν1=Pν2=ϕ1Pg1=ϕ1Psat@10°C (I)

Here, partial pressure at state 2 is Pν2, relative humidity at state 1 is ϕ1, initial vapor pressure is Pg1 and saturation pressure at temperature of 10°C is Psat@10°C.

Express initial partial pressure.

Pa1=P1Pν1 (II)

Here, initial pressure is P1.

Express initial specific volume.

ν1=RaT1Pa1 (III)

Here, universal gas constant of air is Ra and initial temperature is T1.

Express initial specific humidity.

ω1=0.622Pν1P1Pν1 (IV)

The amount or quantity of air moisture will remain constant while flowing through heating section,

ω1=ω2 (V)

Here, specific humidity at state 1 and 2 is ω1andω2 respectively.

Express initial enthalpy.

h1=cpT1+ω1hg1 (VI)

Here, initial specific enthalpy at saturated vapor is hg1, specific heat at constant pressure of air is cp and temperature at state 1 is T1.

Express partial pressure at state 3.

Pν3=ϕ3Pg3=ϕ3Psat@20°C (VII)

Here, relative humidity at state 3 is ϕ3, vapor pressure at state 3 is Pg3 and saturation pressure at temperature of 20°C is Psat@20°C.

Express specific humidity at state 3.

ω3=0.622Pν3P3Pν3 (VIII)

Here, partial pressure at stat3 is Pν3 and pressure at state 3 is P3.

Express enthalpy at state 3.

h3=cpT3+ω3hg3 (IX)

Here, specific enthalpy saturated vapor at state 3 is hg3, specific heat at constant pressure of air is cp and temperature at state 3 is T3.

Express the mass flow rate of dry air.

m˙a=V˙1ν1 (X)

Here, initial volume rate is V˙1 and initial specific volume is ν1.

Express final specific enthalpy by applying an energy balance on the humidifying section.

E˙inE˙out=ΔE˙systemE˙inE˙out=0E˙in=E˙outm˙ihi=m˙ehe

m˙whw+m˙a2h2=m˙ah3(ω3ω2)hw+h2=h3(ω3ω2)hg@100°C+h2=h3h2=h3(ω3ω2)hg@100°C (XI)

Here, the rate of total energy entering the system is E˙in, the rate of total energy leaving the system is E˙out, the rate of change in the total energy of the system is ΔE˙system, initial and exit mass flow rate is m˙iandm˙e respectively, initial and exit specific enthalpy is hiandhe respectively, mass flow rate of water and air is m˙wandm˙a respectively, specific enthalpy of water is hw, mass flow arte at exit of air is m˙a2, specific enthalpy at state 2 and 3 is h2andh3 respectively, specific humidity at state 2 and 3 is ω2andω3 respectively and specific enthalpy saturation vapor at temperature of 100°C is hg@100°C.

Express temperature leaving the heating section.

h2=cpT2+ω2hg2=cpT2+ω2(hg@0.01°C+1.82T2) (XII)

Here, temperature at state 2 is T2.

Express relative humidity leaving the heating section.

ϕ2=Pν2Pg2=Pν2Psat@19.5°C (XIII)

Here, partial pressure at state 2 is Pν2 and saturation pressure at temperature of 19.5°C is Psat@19.5°C.

Conclusion:

Refer Table A-2, “ideal-gas specific heats of various common gases”, and write the gas constant and specific heat at constant pressure of air.

Ra=0.287kPam3/kgcp=1.005kJ/kg°C

Refer Table A-4, “saturated water-temperature table”, and write the saturation pressure at temperature of 10°Cand20°C.

Psat@10°C=1.2281kPaPsat@20°C=2.3392kPa

Substitute 0.70 for ϕ1 and 1.2281kPa for Psat@10°C in Equation (I).

Pν1=Pν2=(0.70)(1.2281kPa)=0.860kPa

Substitute 95kPa for P1 and 0.860kPa for Pν1 in Equation (II).

Pa1=95kPa0.860kPa=94.14kPa

Substitute 0.287kPam3/kg for Ra, 10°C for T1 and 94.14kPa for Pa1 in Equation (III).

ν1=(0.287kPam3/kg)(10°C)94.14kPa=(0.287kPam3/kg)[(10+273)K]94.14kPa=(0.287kPam3/kg)(283K)94.14kPa=0.863m3/kgdryair

Substitute 95kPa for P1 and 0.863kPa for Pν1 in Equation (IV).

ω1=0.622(0.863kPa)95kPa0.863kPa=0.00568kgH2O/kgdryair

Substitute 0.00568kgH2O/kgdryair for ω1 in Equation (V).

ω2=0.00568kgH2O/kgdryair

Refer Table A-4, “saturated water-temperature table”, and write the initial and final specific enthalpy saturated vapor corresponding to temperature of 10°Cand20°C.

hg1=hg@10°C=2519.2kJ/kghg3=hg@20°C=2537.4kJ/kg

Substitute 1.005kJ/kg°C for cp, 10°C for T1, 0.00568 for ω1 and 2519.2kJ/kg for hg1 in Equation (VI).

h1=(1.005kJ/kg°C)(10°C)+(0.00568)(2519.2kJ/kg)=24.36kJ/kgdryair

Substitute 0.60 for ϕ3 and 2.3392kPa for Psat@20°C in Equation (VII).

Pν3=(0.60)(2.3392kPa)=1.40kPa

Substitute 95kPa for P3 and 1.40kPa for Pν3 in Equation (VIII).

ω3=0.622(1.40kPa)95kPa1.40kPa=0.00930kgH2O/kgdryair

Substitute 1.005kJ/kg°C for cp, 20°C for T3, 0.00930 for ω1 and 2537.4kJ/kg for hg3 in Equation (IX).

h3=(1.005kJ/kg°C)(20°C)+(0.0093)(2537.4kJ/kg)=43.70kJ/kgdryair

Substitute 35m3/min for V˙1 and 0.863m3/kgdryair for ν1 in Equation (X).

m˙a=35m3/min0.863m3/kgdryair=40.6kg/min

Refer Table A-4, “saturated water-temperature table”, and write the specific enthalpy saturation vapor at temperature of 100°C.

hg@100°C=2675.6kJ/kg

Substitute 43.70kJ/kgdryair for h3, 0.00930kgH2O/kgdryair for ω3, 0.00568kgH2O/kgdryair for ω2 and 2675.6kJ/kg for hg@100°C in Equation (XI).

h2=43.70kJ/kgdryair[(0.009300.0053)kgH2O/kgdryair](2675.6kJ/kg)=34kJ/kgdryair

Refer Table A-4, “saturated water-temperature table”, and write the specific enthalpy saturation vapor at temperature of 0.01°C.

hg@0.01°C=2500.9kJ/kg

Substitute 34kJ/kgdryair for h2, 1.005kJ/kg°C for cp, 0.00568kgH2O/kgdryair for ω2 and 2500.9kJ/kg for hg@0.01°C in Equation (XII).

34kJ/kgdryair=(1.005kJ/kg°C)T2+0.00568(2500.9+1.82T2)34kJ/kgdryair=(1.005kJ/kg°C)T2+14.205+0.01033T2T2=19.5°C

Hence, the temperature of air when it leaves the heating section is 19.5°C.

Refer Table A-4, “saturated water-temperature table”, and write the saturated vapor at temperature of 19.5°C using an interpolation method.

Write the formula of interpolation method of two variables.

y2=(x2x1)(y3y1)(x3x1)+y1 (XIV)

Here, the variables denote by x and y is temperature and saturated vapor respectively.

Show the saturated vapor corresponding to temperature as in Table (1).

Temperature

T(°C)

Saturated vapor

Psat(kPa)

15 (x1)1.7057 (y1)
19.5 (x2)(y2=?)
20 (x3)2.3392 (y3)

Substitute 15°C,19.5°Cand20°C for x1,x2andx3 respectively, 1.7057kPa for y1 and 2.3392kPa for y3 in Equation (XIV).

y2=(19.5°C15°C)(2.3392kPa1.7057kPa)(20°C15°C)+1.7057kPa=2.2759kPa=Psat@19.5°C

Substitute 0.860kPa for Pν2 and 2.2759kPa for Psat@19.5°C in Equation (XIII).

ϕ2=0.860kPa2.2759kPa=0.377=37.7%

Hence, the relative humidity of air when it leaves the heating section is 37.7% respectively.

(b)

To determine

The rate of heat transfer in the heating section.

(b)

Expert Solution
Check Mark

Answer to Problem 75P

The rate of heat transfer in the heating section is 391kJ/min.

Explanation of Solution

Express the rate of heat transfer in the heating section.

Q˙in=m˙a(h2h1) (XV)

Conclusion:

Substitute 40.6kg/min for m˙a, 34kJ/kgdryair for h2 and 24.36kJ/kgdryair for h1 in Equation (XV).

Q˙in=(40.6kg/min)[(3424.36)kJ/kgdryair]=391kJ/min

Hence, the rate of heat transfer in the heating section is 391kJ/min.

(c)

To determine

The rate at which water is added to the air in the humidifying section.

(c)

Expert Solution
Check Mark

Answer to Problem 75P

The rate at which water is added to the air in the humidifying section is 0.147kg/min.

Explanation of Solution

Express the rate at which water is added to the air in the humidifying section.

m˙w=m˙a(ω3ω2) (V)

Conclusion:

Substitute 40.6kg/min for m˙a, 0.0093kgH2O/kgdryair for ω3 and 0.00568kgH2O/kgdryair for ω2 in Equation (V).

m˙w=(40.6kg/min)(0.00930.00568)kgH2O/kgdryair=0.147kg/min

Hence, the rate at which water is added to the air in the humidifying section is 0.147kg/min.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Homework: ANOVA Table for followed design B AB Dr -1 -1 1 (15.18,12) 1 -1 -1 (45.48.51) -1 1 -1 (25,28,19) 1 1 (75.75,81)
S B Pin 6 mm G
Mid-Term Exam 2024/2025 Post graduate/Applied Mechanics- Metallurgy Q1/ State the type of fault in the following case, and state the structure in which it will appear. АВСАВСВАСВАСАВСАВС

Chapter 14 Solutions

EBK THERMODYNAMICS: AN ENGINEERING APPR

Ch. 14.7 - Is it possible to obtain saturated air from...Ch. 14.7 - Why are the chilled water lines always wrapped...Ch. 14.7 - How would you compare the enthalpy of water vapor...Ch. 14.7 - A tank contains 15 kg of dry air and 0.17 kg of...Ch. 14.7 - Prob. 15PCh. 14.7 - An 8-m3 tank contains saturated air at 30C, 105...Ch. 14.7 - Determine the masses of dry air and the water...Ch. 14.7 - A room contains air at 85F and 13.5 psia at a...Ch. 14.7 - Prob. 19PCh. 14.7 - Prob. 20PCh. 14.7 - Prob. 21PCh. 14.7 - In summer, the outer surface of a glass filled...Ch. 14.7 - In some climates, cleaning the ice off the...Ch. 14.7 - Andy and Wendy both wear glasses. On a cold winter...Ch. 14.7 - Prob. 25PCh. 14.7 - Prob. 26PCh. 14.7 - Prob. 27PCh. 14.7 - A thirsty woman opens the refrigerator and picks...Ch. 14.7 - The air in a room has a dry-bulb temperature of...Ch. 14.7 - Prob. 31PCh. 14.7 - Prob. 32PCh. 14.7 - Prob. 33PCh. 14.7 - How do constant-enthalpy and...Ch. 14.7 - At what states on the psychrometric chart are the...Ch. 14.7 - How is the dew-point temperature at a specified...Ch. 14.7 - Can the enthalpy values determined from a...Ch. 14.7 - Atmospheric air at a pressure of 1 atm and...Ch. 14.7 - Prob. 39PCh. 14.7 - Prob. 40PCh. 14.7 - Prob. 41PCh. 14.7 - Atmospheric air at a pressure of 1 atm and...Ch. 14.7 - Reconsider Prob. 1443. Determine the adiabatic...Ch. 14.7 - What does a modern air-conditioning system do...Ch. 14.7 - How does the human body respond to (a) hot...Ch. 14.7 - How does the air motion in the vicinity of the...Ch. 14.7 - Consider a tennis match in cold weather where both...Ch. 14.7 - Prob. 49PCh. 14.7 - Prob. 50PCh. 14.7 - Prob. 51PCh. 14.7 - Prob. 52PCh. 14.7 - What is metabolism? What is the range of metabolic...Ch. 14.7 - Why is the metabolic rate of women, in general,...Ch. 14.7 - What is sensible heat? How is the sensible heat...Ch. 14.7 - Prob. 56PCh. 14.7 - Prob. 57PCh. 14.7 - Prob. 58PCh. 14.7 - Prob. 59PCh. 14.7 - Repeat Prob. 1459 for an infiltration rate of 1.8...Ch. 14.7 - An average (1.82 kg or 4.0 lbm) chicken has a...Ch. 14.7 - An average person produces 0.25 kg of moisture...Ch. 14.7 - How do relative and specific humidities change...Ch. 14.7 - Prob. 64PCh. 14.7 - Humid air at 150 kPa, 40C, and 70 percent relative...Ch. 14.7 - Humid air at 40 psia, 50F, and 90 percent relative...Ch. 14.7 - Prob. 67PCh. 14.7 - Air enters a 30-cm-diameter cooling section at 1...Ch. 14.7 - Prob. 69PCh. 14.7 - Prob. 70PCh. 14.7 - Why is heated air sometimes humidified?Ch. 14.7 - Air at 1 atm, 15C, and 60 percent relative...Ch. 14.7 - Air at 14.7 psia, 35F, and 50 percent relative...Ch. 14.7 - An air-conditioning system operates at a total...Ch. 14.7 - Prob. 75PCh. 14.7 - Why is cooled air sometimes reheated in summer...Ch. 14.7 - Atmospheric air at 1 atm, 30C, and 80 percent...Ch. 14.7 - Ten thousand cubic feet per hour of atmospheric...Ch. 14.7 - Air enters a 40-cm-diameter cooling section at 1...Ch. 14.7 - Repeat Prob. 1479 for a total pressure of 88 kPa...Ch. 14.7 - On a summer day in New Orleans, Louisiana, the...Ch. 14.7 - Prob. 83PCh. 14.7 - Prob. 84PCh. 14.7 - Prob. 85PCh. 14.7 - Saturated humid air at 70 psia and 200F is cooled...Ch. 14.7 - Humid air is to be conditioned in a...Ch. 14.7 - Atmospheric air at 1 atm, 32C, and 95 percent...Ch. 14.7 - Prob. 89PCh. 14.7 - Prob. 90PCh. 14.7 - Does an evaporation process have to involve heat...Ch. 14.7 - Prob. 92PCh. 14.7 - Prob. 93PCh. 14.7 - Air enters an evaporative (or swamp) cooler at...Ch. 14.7 - Prob. 95PCh. 14.7 - Air at 1 atm, 20C, and 70 percent relative...Ch. 14.7 - Two unsaturated airstreams are mixed...Ch. 14.7 - Consider the adiabatic mixing of two airstreams....Ch. 14.7 - Two airstreams are mixed steadily and...Ch. 14.7 - A stream of warm air with a dry-bulb temperature...Ch. 14.7 - Prob. 104PCh. 14.7 - Prob. 105PCh. 14.7 - How does a natural-draft wet cooling tower work?Ch. 14.7 - What is a spray pond? How does its performance...Ch. 14.7 - The cooling water from the condenser of a power...Ch. 14.7 - A wet cooling tower is to cool 60 kg/s of water...Ch. 14.7 - Prob. 110PCh. 14.7 - Prob. 111PCh. 14.7 - Water at 30C is to be cooled to 22C in a cooling...Ch. 14.7 - Prob. 113PCh. 14.7 - Prob. 114RPCh. 14.7 - Determine the mole fraction of dry air at the...Ch. 14.7 - Prob. 116RPCh. 14.7 - Prob. 117RPCh. 14.7 - Prob. 118RPCh. 14.7 - Prob. 119RPCh. 14.7 - Prob. 120RPCh. 14.7 - Prob. 121RPCh. 14.7 - Prob. 122RPCh. 14.7 - Prob. 124RPCh. 14.7 - Prob. 125RPCh. 14.7 - Prob. 126RPCh. 14.7 - Prob. 128RPCh. 14.7 - Prob. 129RPCh. 14.7 - Air enters a cooling section at 97 kPa, 35C, and...Ch. 14.7 - Prob. 131RPCh. 14.7 - Atmospheric air enters an air-conditioning system...Ch. 14.7 - Humid air at 101.3 kPa, 36C dry bulb and 65...Ch. 14.7 - An automobile air conditioner uses...Ch. 14.7 - Prob. 135RPCh. 14.7 - Prob. 137RPCh. 14.7 - Conditioned air at 13C and 90 percent relative...Ch. 14.7 - Prob. 141FEPCh. 14.7 - A 40-m3 room contains air at 30C and a total...Ch. 14.7 - A room is filled with saturated moist air at 25C...Ch. 14.7 - Prob. 144FEPCh. 14.7 - The air in a house is at 25C and 65 percent...Ch. 14.7 - Prob. 146FEPCh. 14.7 - Air at a total pressure of 90 kPa, 15C, and 75...Ch. 14.7 - On the psychrometric chart, a cooling and...Ch. 14.7 - On the psychrometric chart, a heating and...Ch. 14.7 - An airstream at a specified temperature and...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY