Programmable Logic Controllers
5th Edition
ISBN: 9780073373843
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 13, Problem 7P
A specific output is forced on, but the LED module indicator does not come on. A check of the voltage at the output module indicates a voltage far below the normal on level. What is the first thing to check?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Arduino programming exercises using Uno Microcontroller
Write a program that starts out by flashing an LED connected to pin7 at 2Hz. On a button press (button is attached to pin4 – wire active low), the LED turns on for 2 seconds. After this the whole cycle repeats.
* In the figure attached, the output voltage (Vout) will not equal to zero when the
:switch is
t = 0
R
www
VS
Vout
Closed at Zero
Opened at zero
Open
Closed
The engine will start 30 seconds after the S1 start button is pressed, and it will stop after 40 seconds. It will start working again after 30 seconds and this situation will continue until the S2 stop button is pressed. (Plc lesson) Draw the stl and the leader.
Chapter 13 Solutions
Programmable Logic Controllers
Ch. 13 - Prob. 1RQCh. 13 - Prob. 2RQCh. 13 - Prob. 3RQCh. 13 - List three potential noise-generating inductive...Ch. 13 - Prob. 5RQCh. 13 - Prob. 6RQCh. 13 - Prob. 7RQCh. 13 - Under what condition can a ground loop circuit be...Ch. 13 - Prob. 9RQCh. 13 - What operating state will cause an inductive load...
Ch. 13 - Prob. 11RQCh. 13 - Prob. 12RQCh. 13 - Prob. 13RQCh. 13 - Prob. 14RQCh. 13 - Prob. 15RQCh. 13 - List four uses for the data monitor function.Ch. 13 - Prob. 17RQCh. 13 - Prob. 18RQCh. 13 - Prob. 19RQCh. 13 - Prob. 20RQCh. 13 - Prob. 21RQCh. 13 - Prob. 22RQCh. 13 - Prob. 23RQCh. 13 - Prob. 24RQCh. 13 - Prob. 25RQCh. 13 - Prob. 26RQCh. 13 - Prob. 27RQCh. 13 - Prob. 28RQCh. 13 - Prob. 29RQCh. 13 - Prob. 30RQCh. 13 - Prob. 1PCh. 13 - A fuse is blown in an output module. Suggest two...Ch. 13 - Prob. 3PCh. 13 - Prob. 4PCh. 13 - Prob. 5PCh. 13 - Prob. 6PCh. 13 - A specific output is forced on, but the LED module...Ch. 13 - An electronic-based input sensor is wired to a...Ch. 13 - Prob. 9PCh. 13 - Prob. 11PCh. 13 - Prob. 12PCh. 13 - Prob. 13PCh. 13 - The program of Figure 13-39 is supposed to execute...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Computer Science Find the resistor value to create a timer for 100 second using 0.002 F CapacitorMulti Line Text.arrow_forwardArduino programming exercises using Uno Microcontroller Write a program that starts by having a red LED attached to pin 8 go on. The LED will stay on until a button is pressed. A half second after the button is pressed, the red LED will go off and a green LED will go on for 5 seconds. After this the whole cycle repeats.arrow_forwardThere are two lamps used to illuminate the well, the first lamp is installed at the top of the wellI, and the second lamp is installed at a distance from the first using the Arduino board. Make the two lamps light at the same time using only one switcharrow_forward
- Arduino programming exercises using Uno Microcontroller Write a program that turns on an LED attached to pin 3 for 5 seconds then turns it off. The light should stay off for 3 seconds and then the LED should blink 10 times at a rate of 1 Hz (on and off each second).arrow_forwardComputer Science Build an Arduino system that displays the current temperature in Celsius degree and light intensity on LCD and Use potentiometer to control the brightness of the LCD.arrow_forwardThe lights in a classroom are controlled by two switches: one at the back and one at the front of the room. Moving either switch to the opposite position turns the lights off if they are on and on if they are off. Assume the lights have been installed so that when both switches are in the down position, the lights are off. Design a circuit to control the switchesarrow_forward
- The input waveform shown in the figure below is applied to an inverter, which is used to operate a light on a control circuit. Draw the timing diagram of the output waveform in proper relation to the input. VIN HIGH LOW urrarrow_forwardQ1: What inputs and output does the system detect and where are these locations? Q2: What logic gates are used for the landing gear warning logic module?arrow_forwardTake careful notes on the input and output settings for the system.arrow_forward
- Purpose: The entry/Exit of the parking lot is a single lane passage. By controlling the indicators, the program ensures that only one car can pass through the Entry/Exit so as to prevent car accident between entering and leaving cars. Y1 X1 Program Description: In the parking lot, there are two light indicators individually directing the entering and leaving cars. By the interlock control circuit, only one indicator will show "GO" signal and the car accident will thus be prevented. When an the same time, the leaving car indicator will show "STOP". Car entering is allowed but leaving is prohibited in this case. When a leaving car draws near the vehicle control barrier, X1 will be ON and so will Y1. The leaving car indicator will show "GO" and the entering car indicator will show "STOP"| draws near the vehicle control barrier, XO will be ON and so will YO. The entering car indicator will show "GO". At TOP GOarrow_forwardA microcontroller of PIC16F84A and a 7-segment LED are used to form an down- count counter from 9 to 0. The input devices and 7-segment LED on the operation panel are shown in Figure 3.1 while the related electronic circuit and Flowcode program are as shown in Figures 3.2 and 3.3, respectively. Answer the following questions if the counter is operated at high level input voltage those are controlled by the input devices for the data input and stop functions. Count Stop LED Counter Figure 3.1 A countdown counter using 7-segment LED Count (1) X1 U1 16 15 17 OSCICLKIN oscziCLKOUT RAD RA1 18 Stop RAZ RAS RAATOCKI 4 MCLR 4MHZ CRYSTAL C1 C2 RBOINT RB1 RB2 RB3 RB4 RBS RB6 RB7 22pF PIC16F84A SV RO Figure 3.2 Electronic cireuit for the counter -lelalarrow_forwardStepper motor control using ULN2003 IC in 16F877 microcontroller will be carried out. In the program, stepper motor and driver IC will be connected to PORTD. to RA0 pin When the connected button is pressed, the stepper motor will turn to the left with half a step and one speed, to pin RA1. When the connected button is pressed, the motor will turn to the right at a certain speed. button connected to RA2 pin When pressed, the motor will be stopped no matter which direction it turns. During engine operation (right or left) If the button connected to the RA3 pin is pressed, the motor speed will double. Working logic Write the program described (solve with ccs)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- A+ Guide To It Technical SupportComputer ScienceISBN:9780357108291Author:ANDREWS, Jean.Publisher:Cengage,A+ Guide to Hardware (Standalone Book) (MindTap C...Computer ScienceISBN:9781305266452Author:Jean AndrewsPublisher:Cengage LearningEnhanced Discovering Computers 2017 (Shelly Cashm...Computer ScienceISBN:9781305657458Author:Misty E. Vermaat, Susan L. Sebok, Steven M. Freund, Mark Frydenberg, Jennifer T. CampbellPublisher:Cengage Learning
A+ Guide To It Technical Support
Computer Science
ISBN:9780357108291
Author:ANDREWS, Jean.
Publisher:Cengage,
A+ Guide to Hardware (Standalone Book) (MindTap C...
Computer Science
ISBN:9781305266452
Author:Jean Andrews
Publisher:Cengage Learning
Enhanced Discovering Computers 2017 (Shelly Cashm...
Computer Science
ISBN:9781305657458
Author:Misty E. Vermaat, Susan L. Sebok, Steven M. Freund, Mark Frydenberg, Jennifer T. Campbell
Publisher:Cengage Learning
What is a Thyristor? - A Galco TV Tech Tip; Author: GalcoTV;https://www.youtube.com/watch?v=LBb_Qz7J3zA;License: Standard Youtube License