Arduino programming exercises using Uno Microcontroller Write a program that starts by having a red LED attached to pin 8 go on. The LED will stay on until a button is pressed. A half second after the button is pressed, the red LED will go off and a green LED will go on for 5 seconds. After this the whole cycle repeats.

Arduino programming exercises using Uno Microcontroller Write a program that starts by having a red LED attached to pin 8 go on. The LED will stay on until a button is pressed. A half second after the button is pressed, the red LED will go off and a green LED will go on for 5 seconds. After this the whole cycle repeats.

C++ Programming: From Problem Analysis to Program Design

8th Edition

ISBN:9781337102087

Author:D. S. Malik

Publisher:D. S. Malik

Chapter2: Basic Elements Of C++

Section: Chapter Questions

Problem 24PE: 24. A piece of wire is to be bent in the form of a rectangle to put around a picture frame. The...

See similar textbooks

Similar questions

Arduino programming exercises using Uno Microcontroller Write a program that lights an LED attached to pin 3. The LED should turn off after a button attached to pin 4 has been pushed 3 times. Assume the button is wired active low. Assume there is least 1/4 second between button presses.
Arduino programming exercises using Uno Microcontroller Write a program that starts out by flashing an LED connected to pin7 at 2Hz. On a button press (button is attached to pin4 – wire active low), the LED turns on for 2 seconds. After this the whole cycle repeats.
Arduino programming exercises using Uno Microcontroller Write a program that operates a train crossing light. The lights should flash at a rate of 2 Hz (on, off, on, off in 1 second) and operate for 20 seconds.
Arduino programming exercises using Uno Microcontroller Write a program that flashes an LED 10 times at a rate of 2 Hz every time a button is pressed. Assume the button is wired active low.
Describe counter controlled while loops.
Arduino programming exercises using Uno Microcontroller Write a program that turns on an LED attached to pin 3 for 5 seconds then turns it off. The light should stay off for 3 seconds and then the LED should blink 10 times at a rate of 1 Hz (on and off each second).
Computer Science Build an Arduino system that displays the current temperature in Celsius degree and light intensity on LCD and Use potentiometer to control the brightness of the LCD.
24. A piece of wire is to be bent in the form of a rectangle to put around a picture frame. The length of the picture frame is 1.5 times the width. Write a program that prompts the user to input the length of the wire and outputs the length and width of the picture frame.
ZAIN ID A traffic light is installed at a junction of a railroad and a road of cars. The traffic light is controlled by two switches in the rail placed one mile apart on either side of the junction. A switch is turned on when the train is over it and is turned off otherwise. When the beginning of the train is one mile from the junction, the traffic light is changed from green (logic "O") to red (logic "1"). The light is changed back to green when the end of the train is one mile away from the junction and S1 is turned off. Assume that the length of the train is less than two miles. The circuit diagram of the aforementioned state machine includes . SR-flip flop(s). * Imile 1mile
Purpose: The entry/Exit of the parking lot is a single lane passage. By controlling the indicators, the program ensures that only one car can pass through the Entry/Exit so as to prevent car accident between entering and leaving cars. Y1 X1 Program Description: In the parking lot, there are two light indicators individually directing the entering and leaving cars. By the interlock control circuit, only one indicator will show "GO" signal and the car accident will thus be prevented. When an the same time, the leaving car indicator will show "STOP". Car entering is allowed but leaving is prohibited in this case. When a leaving car draws near the vehicle control barrier, X1 will be ON and so will Y1. The leaving car indicator will show "GO" and the entering car indicator will show "STOP"| draws near the vehicle control barrier, XO will be ON and so will YO. The entering car indicator will show "GO". At TOP GO
Compare CALL and PUSH instructions
2-write an Arduino program to turn ON three LED(s) where the first LED works when press the first key, the second LED works when you press a key second and third works when you press the third key.The push buttons are connected on the A0,A1 and A4 respectively.