University Physics with Modern Physics (14th Edition)
14th Edition
ISBN: 9780321973610
Author: Hugh D. Young, Roger A. Freedman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 10, Problem 10.65P
Two weights are connected by a very light, flexible cord that passes over an 80.0-N frictionless pulley of radius 0.300 m. The pulley is a solid uniform disk and is supported by a hook connected to the ceiling (Fig. P10.65). What force does the ceiling exert on the hook?
Figure P10.65
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A box is being lowered from a height of 10m to the ground. A rope is attached to a cylinder. The cylinder is stationary and can be modeled as a solid disc and is 50kg with a radius of 0.8m. The cylinder is frictionless. The box has a mass of 80kg. If the box starts from rest, what is the speed right before it touches the ground?4
A bowler uses a lane with a coefficient of kinetic friction of 0.133. The bowler releases her 4.65 kg bowling ball with a
translational speed of 3.20 m/s. At the moment of release, the ball is not rotating. As the ball slides, it begins to rotate.
What is the work Wnc done by friction on the ball before it transitions to rolling without slipping? Use g = 9.81 m/s² for the
acceleration due to gravity.
Wnc =
An object starts from rest at the top of an inclined plane and moves down. Friction and air resistance can be ignored.
Assume that the object is sliding, but not rolling, so its rotational kinetic energy is O J. The plane is inclined at an angle
of 30.0 degrees from the horizontal and its length is 1.80 m. What is the object's speed when it is located at the bottom
of the inclined plane? Use g = 9.80 m/s² as the magnitude of the acceleration due to gravity.
Jum
Chapter 10 Solutions
University Physics with Modern Physics (14th Edition)
Ch. 10.1 - The accompanying figure shows a force P being...Ch. 10.2 - The figure shows a glider of mass m1 that can...Ch. 10.3 - Suppose the solid cylinder used as a yo-yo in...Ch. 10.4 - You apply equal torques to two different...Ch. 10.5 - A ball is attached to one end of a piece of...Ch. 10.6 - If the polar ice caps were to melt completely due...Ch. 10.7 - Suppose the mass of the flywheel in Fig. 10.34 is...Ch. 10 - Can a single force applied to a body change both...Ch. 10 - Suppose you could use wheels of any type in the...Ch. 10 - Serious bicyclists say that if you reduce the...
Ch. 10 - The harder you hit the brakes while driving...Ch. 10 - When an acrobat walks on a tightrope, she extends...Ch. 10 - When you turn on an electric motor, it takes...Ch. 10 - The work done by a force is the product of force...Ch. 10 - A valued client brings a treasured ball to your...Ch. 10 - You make two versions of the same object out of...Ch. 10 - Two identical masses are attached to frictionless...Ch. 10 - The force of gravity acts on the baton in Fig....Ch. 10 - A certain solid uniform bail reaches a maximum...Ch. 10 - A wheel is rolling without slipping on a...Ch. 10 - A hoop, a uniform solid cylinder, a spherical...Ch. 10 - A ball is rolling along al speed without slipping...Ch. 10 - You are standing at the center of a large...Ch. 10 - Global Warming. If the earths climate continues to...Ch. 10 - It two spinning objects have the same angular...Ch. 10 - A student is sitting on a frictionless rotating...Ch. 10 - A point particle travels in a straight line at...Ch. 10 - In Example 10.10 (Section 10.6) the angular speed ...Ch. 10 - In Example 10.10 (Section 10.6) the rotational...Ch. 10 - As discussed in Section 10.6, the angular momentum...Ch. 10 - If you stop a spinning raw egg for the shortest...Ch. 10 - A helicopter has a large main rotor that rotates...Ch. 10 - In a common design for a gyroscope, the flywheel...Ch. 10 - A gyroscope is precessing about a vertical axis....Ch. 10 - A gyroscope takes 3.8 s to precess 1.0 revolution...Ch. 10 - A gyroscope is precessing as in Fig. 10.32. What...Ch. 10 - A bullet spins on its axis as it emerges from a...Ch. 10 - Calculate the torque (magnitude and direction)...Ch. 10 - Calculate the net torque about point O for the two...Ch. 10 - A square metal plate 0.180m on each side is...Ch. 10 - Three forces are applied to a wheel of radius...Ch. 10 - One force acting on a machine part is...Ch. 10 - A metal bar is in the xy-plane with one end of the...Ch. 10 - A machinist is using a wrench lo loosen a nut. The...Ch. 10 - A uniform disk with mass 40.0 kg and radius 0.200...Ch. 10 - The flywheel of an engine has moment of inertia...Ch. 10 - A cord is wrapped around ihe rim of a solid...Ch. 10 - A machine part has the shape of u solid uniform...Ch. 10 - CP A stone is suspended from the free end of a...Ch. 10 - Prob. 10.13ECh. 10 - CP A 15.0-kg bucket of water is suspended by a...Ch. 10 - A wheel rotates without friction about a...Ch. 10 - A 12.0-kg box resting on a horizontal,...Ch. 10 - A 2.20-kg hoop 1.20 m in diameter is rolling to...Ch. 10 - BIO Gymnastics. We can roughly model a gymnastic...Ch. 10 - What fraction of the total kinetic energy is...Ch. 10 - A siring is wrapped several times around the rim...Ch. 10 - A solid ball is released from rest and slides down...Ch. 10 - A hollow, spherical shell with mass 2.00 kg rolls...Ch. 10 - A 392-N wheel comes off a moving truck and rolls...Ch. 10 - A uniform marble rolls down a symmetrical bowl,...Ch. 10 - A thin, light string is wrapped around the outer...Ch. 10 - A Ball Rolling Uphill. A bowling ball rolls...Ch. 10 - A size-5 soccer ball of diameter 22.6 cm and mass...Ch. 10 - A size-5 soccer ball of diameter 22.6 cm and mass...Ch. 10 - A playground merry-go-round has radius 2.40 m and...Ch. 10 - An engine delivers 175 hp to an aircraft propeller...Ch. 10 - A 2.80-kg grinding wheel is in the form of a solid...Ch. 10 - An electric motor consumes 9.00 kJ of electrical...Ch. 10 - (a) Compute the torque developed by an industrial...Ch. 10 - An airplane propeller is 2.08 m in length (from...Ch. 10 - A 2.00-kg rock has a horizontal velocity of...Ch. 10 - A woman with mass 50 kg is standing on the rim of...Ch. 10 - Find the magnitude of the angular momentum of the...Ch. 10 - (a) Calculate the magnitude of the angular...Ch. 10 - CALC A hollow, thin-walled sphere of mass 12.0 kg...Ch. 10 - CP A small block on a frictionless, horizontal...Ch. 10 - Prob. 10.41ECh. 10 - A diver comes off a board with arms straight up...Ch. 10 - The Spinning Figure Skater. The outstretched hands...Ch. 10 - A solid wood door 1.00 m wide and 2.00 m high is...Ch. 10 - A large wooden turntable in the shape of a flat...Ch. 10 - Asteroid Collision! Suppose that an asteroid...Ch. 10 - Prob. 10.47ECh. 10 - A thin uniform rod has a length of 0.500 m and is...Ch. 10 - A thin, uniform metal bar. 2.00 m long and...Ch. 10 - A uniform. 4.5-kg, square, solid wooden gate 1.5 m...Ch. 10 - The rotor (flywheel) of a loy gyroscope has mass...Ch. 10 - A Gyroscope on the Moon. A certain gyroscope...Ch. 10 - Stabilization of the Hubble Space Telescope. The...Ch. 10 - A 50.0-kg grindstone is a solid disk 0.520 m in...Ch. 10 - 10.55A grindstone in the shape of a solid disk...Ch. 10 - A uniform, 8.40-kg, spherical shell 50.0 cm in...Ch. 10 - A thin, uniform. 3.80-kg bar, 80.0 cm long, has...Ch. 10 - You are designing a simple elevator system for an...Ch. 10 - The Atwoods Machine. Figure P10.59 illustrates an...Ch. 10 - The mechanism shown in Fig. P10.60 is used to...Ch. 10 - A large 16.0-kg roll of paper with radius R = 18.0...Ch. 10 - A block with mass m = 5.00 kg slides down a...Ch. 10 - Two metal disks, one with radius R1 = 2.50 cm and...Ch. 10 - A lawn roller in the form of a thin-walled, hollow...Ch. 10 - Two weights are connected by a very light,...Ch. 10 - You complain about fire safety to the landlord of...Ch. 10 - The Yo-yo. A yo-yo is made from two uniform disks,...Ch. 10 - CP A thin-walled, hollow spherical shell of mass m...Ch. 10 - A basketball (which can be closely modeled as a...Ch. 10 - CP A solid uniform ball rolls without slipping up...Ch. 10 - Rolling Stones. A solid, uniform, spherical...Ch. 10 - You are designing a system for moving aluminum...Ch. 10 - A 42.0-cm-diameter wheel, consisting of a rim and...Ch. 10 - A uniform, 0.0300-kg rod of length 0.400 in...Ch. 10 - A uniform solid cylinder with mass M and radius 2R...Ch. 10 - Tarzan and Jane in the 21st Century. Tarzan has...Ch. 10 - A 5.00-kg ball is dropped from a height of 12.0 m...Ch. 10 - The solid wood door of a gymnasium is 1.00 m wide...Ch. 10 - A uniform rod of length L rests on a friction less...Ch. 10 - CP A large turntable with radius 6.00 m rotates...Ch. 10 - In your job as a mechanical engineer you are...Ch. 10 - A local ice hockey team has asked you to design an...Ch. 10 - You are designing a slide for a water park. In a...Ch. 10 - Neutron Star Glitches. Occasionally, a rotating...Ch. 10 - A 500.0-g bird is flying horizontally at 2.25 m/s,...Ch. 10 - CP A small block with mass 0.130 kg is attached to...Ch. 10 - A 55-kg runner runs around the edge of a...Ch. 10 - DATA The V6 engine in a 2014 Chevrolet Silverado...Ch. 10 - DATA You have one object of each of these shapes,...Ch. 10 - DATA You are testing a small flywheel (radius...Ch. 10 - CALC A block with mass m is revolving with linear...Ch. 10 - When an object is rolling without slipping, the...Ch. 10 - A demonstration gyroscope wheel is constructed by...Ch. 10 - The moment of inertia of the empty turntable is...Ch. 10 - While the turntable is being accelerated, the...Ch. 10 - A doubling of the torque produces a greater...Ch. 10 - If the bodys center of mass were not placed on the...
Additional Science Textbook Solutions
Find more solutions based on key concepts
Which value, apparent magnitude, or absolute magnitude, do you think:
tells us how bright an object will appear...
Lecture- Tutorials for Introductory Astronomy
A frame of reference placed at the center of the Sun inertial one. Why is it not exactly an inertial frame?
College Physics
A spider of mass ms drapes a silk thread of negligible mass over a stick with its far end a distance h off the ...
Essential University Physics: Volume 1 (3rd Edition)
Write the SI unit for each abbreviation.
29. 27 mm
Applied Physics (11th Edition)
Two identical bubbles of gas form at the bottom of a lake, then rise to the surface. Because the pressure is mu...
An Introduction to Thermal Physics
A light ray propagates in a transparent material at 15 to the normal to the surface. It emerges into the surrou...
Essential University Physics: Volume 2 (3rd Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A solid cylinder has a mass of 1 kg and a radius of 0.1 m. Starting from rest, the cylinder rolls down a ramp angled at 30° from the horizontal. The ramp is 1 m long and the cylinder rolls without slipping. How fast is it traveling parallel to the ramp at the moment it reaches the bottom? Take g = 10 m/s². L = 1m 30°arrow_forwardA uniform rod is set up so that it can rotate about an axis at perpendicular to one of its ends. The length and mass of the rod are 0.873 m and 1.11 kg, respectively. A force of constant magnitude ?F acts on the rod at the end opposite the rotation axis. The direction of the force is perpendicular to both the rod's length and the rotation axis. Calculate the value of ?F that will accelerate the rod from rest to an angular speed of 6.35 rad/s in 8.37 s.arrow_forwardA school has installed a modestly-sized wind turbine. The three blades are 4.6 m long; each blade has a mass of 45 kg. You can assume that the blades are uniform along their lengths. When the blades spin at 240 rpm, what is the kinetic energy of the blade assembly?arrow_forward
- A uniform rod is set up so that it can rotate about an axis at perpendicular to one of its ends. The length and mass of the rod are 0.701 m and 1.15 kg , respectively. A force of constant magnitude ? acts on the rod at the end opposite the rotation axis. The direction of the force is perpendicular to both the rod's length and the rotation axis. Calculate the value of ? that will accelerate the rod from rest to an angular speed of 6.47 rad/s in 8.27 s .arrow_forwardA 250 gg , 25-cm-diameter plastic disk is spun on an axle through its center by an electric motor. What torque must the motor supply to take the disk from 0 to 1800 rpm in 4.3 s ?arrow_forwardQuestion 2 a. A 5.0 kg object has an initial velocity of (5.0i -3.0j) m/s. What is its kinetic energy at this time? KE = ½ mv² where v² = V.V b. The position vector of an object is r = (4i - 5j). If a force F = (2i+3j) N acts on the object, calculate the torque t produced. t = rx Farrow_forward
- A bowler uses a lane with a coefficient of kinetic friction of 0.156. The bowler releases her 5.30 kg bowling ball with a translational speed of 3.45 m/s. At the moment of release, the ball is not rotating. As the ball slides, it begins to rotate. What is the work ?ncWnc done by friction on the ball before it transitions to rolling without slipping? Use g=9.81 m/s2 for the acceleration due to gravity.arrow_forwardA particular horizontal turntable can be modeled as a uniform disk with a mass of 230 g and a radius of 26.0 cm that rotates without friction about a vertical axis passing through its center. The angular speed of the turntable is 3.00 rad/s. A ball of clay, with a mass of 40.0 g, is dropped from a height of 25.0 cm above the turntable. It hits the turntable at a distance of 15.0 cm from the middle, and sticks where it hits. Assuming the turntable is firmly supported by its axle so it remains horizontal at all times, find the final angular speed of the turntable-clay system. rad/sarrow_forwardPart A. Compute the torque developed by an industrial motor whose output is 175 kW at an angular speed of 5000rev/min. Part B A drum with negligible mass, 0.600 m in diameter, is attached to the motor shaft, and the power output of the motor is used to raise a weight hanging from a rope wrapped around the drum. How heavy a weight can the motor lift at a constant speed? Part C At what constant speed will the weight rise?arrow_forward
- A uniform rod is set up so that it can rotate about an axis at perpendicular to one of its ends. The length and mass of the rod are 0.773 m and 1.27 kg, respectively. A force of constant magnitude F acts on the rod at the end opposite the rotation axis. The direction of the force is perpendicular to both the rod's length and the rotation axis. Calculate the value of F that will accelerate the rod from rest to an angular speed of 6.05 rad/s in 8.43 s. F = about us careers privacy policy terms of use contact us help tv MacBook Airarrow_forwardA 210 g , 34.0-cm-diameter turntable rotates on frictionless bearings at 65.0 rpm . A 21.0 g block sits at the center of the turntable. A compressed spring shoots the block radically outward along a frictionless groove in the surface of the turntable. What is the turntable's rotation angular velocity when the block reaches the outer edge?arrow_forwardA uniform rod is set up so that it can rotate about an axis at perpendicular to one of its ends. The length and mass of the rod are 0.801 m and 1.25 kg, respectively. A force of constant magnitude F acts on the rod at the end opposite the rotation axis. The direction of the force is perpendicular to both the rod's length and the rotation axis. Calculate the value of F that will accelerate the rod from rest to an angular speed of 6.49 rad/s in 8.61 s. F =arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Rotational Kinetic Energy; Author: AK LECTURES;https://www.youtube.com/watch?v=s5P3DGdyimI;License: Standard YouTube License, CC-BY