University Physics with Modern Physics (14th Edition)
14th Edition
ISBN: 9780321973610
Author: Hugh D. Young, Roger A. Freedman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 10, Problem 10.32E
An electric motor consumes 9.00 kJ of electrical energy in 1.00 min. If one-third of this energy goes into heat and other forms of internal energy of the motor, with the rest going to the motor output, how much torque will this engine develop if you run it at 2500 rpm?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A molecule in a microwave oven experiences a torque t = to sin 0. How much work must
be done to rotate the molecule from 0 = 0° to = 110° ? Where, to is a constant.
(a) Which component of the horizontal axis wind turbine can be considered as the brain of the system? Write
the important functions of this component. Explain how it coordinates with the anemometer, wind vane and
yaw drive for the proper working of turbine. I
(b) Explain, why wind energy is considered as highly desirable and economical to the rural areas which are far
from existing grids
On your bike, you start from rest and accelerate to the
speed of 5 m/s in 20 s (assume constant acceleration),
and keep going at this speed on a level ground for
further 500 m. During your trip, the average air drag
force on you is 13 N, and the rolling friction force is
9 N. Assume 75 kg total mass of yourself and the bike,
20% mechanical energy efficiency in your body, and a
BMR of 100 W. How much Calories you have spent to
accomplish this?
Draw the energy model of the situation!
k
Hint: "Average air drag force" means that you can use
the same value of the air drag over the whole travle
distance, for both acceleration stage and motion with a
constant speed. We know that the air drag force in fact
depends on speed, but since the average value i
you do not need to care about it.
Calculat
Chapter 10 Solutions
University Physics with Modern Physics (14th Edition)
Ch. 10.1 - The accompanying figure shows a force P being...Ch. 10.2 - The figure shows a glider of mass m1 that can...Ch. 10.3 - Suppose the solid cylinder used as a yo-yo in...Ch. 10.4 - You apply equal torques to two different...Ch. 10.5 - A ball is attached to one end of a piece of...Ch. 10.6 - If the polar ice caps were to melt completely due...Ch. 10.7 - Suppose the mass of the flywheel in Fig. 10.34 is...Ch. 10 - Can a single force applied to a body change both...Ch. 10 - Suppose you could use wheels of any type in the...Ch. 10 - Serious bicyclists say that if you reduce the...
Ch. 10 - The harder you hit the brakes while driving...Ch. 10 - When an acrobat walks on a tightrope, she extends...Ch. 10 - When you turn on an electric motor, it takes...Ch. 10 - The work done by a force is the product of force...Ch. 10 - A valued client brings a treasured ball to your...Ch. 10 - You make two versions of the same object out of...Ch. 10 - Two identical masses are attached to frictionless...Ch. 10 - The force of gravity acts on the baton in Fig....Ch. 10 - A certain solid uniform bail reaches a maximum...Ch. 10 - A wheel is rolling without slipping on a...Ch. 10 - A hoop, a uniform solid cylinder, a spherical...Ch. 10 - A ball is rolling along al speed without slipping...Ch. 10 - You are standing at the center of a large...Ch. 10 - Global Warming. If the earths climate continues to...Ch. 10 - It two spinning objects have the same angular...Ch. 10 - A student is sitting on a frictionless rotating...Ch. 10 - A point particle travels in a straight line at...Ch. 10 - In Example 10.10 (Section 10.6) the angular speed ...Ch. 10 - In Example 10.10 (Section 10.6) the rotational...Ch. 10 - As discussed in Section 10.6, the angular momentum...Ch. 10 - If you stop a spinning raw egg for the shortest...Ch. 10 - A helicopter has a large main rotor that rotates...Ch. 10 - In a common design for a gyroscope, the flywheel...Ch. 10 - A gyroscope is precessing about a vertical axis....Ch. 10 - A gyroscope takes 3.8 s to precess 1.0 revolution...Ch. 10 - A gyroscope is precessing as in Fig. 10.32. What...Ch. 10 - A bullet spins on its axis as it emerges from a...Ch. 10 - Calculate the torque (magnitude and direction)...Ch. 10 - Calculate the net torque about point O for the two...Ch. 10 - A square metal plate 0.180m on each side is...Ch. 10 - Three forces are applied to a wheel of radius...Ch. 10 - One force acting on a machine part is...Ch. 10 - A metal bar is in the xy-plane with one end of the...Ch. 10 - A machinist is using a wrench lo loosen a nut. The...Ch. 10 - A uniform disk with mass 40.0 kg and radius 0.200...Ch. 10 - The flywheel of an engine has moment of inertia...Ch. 10 - A cord is wrapped around ihe rim of a solid...Ch. 10 - A machine part has the shape of u solid uniform...Ch. 10 - CP A stone is suspended from the free end of a...Ch. 10 - Prob. 10.13ECh. 10 - CP A 15.0-kg bucket of water is suspended by a...Ch. 10 - A wheel rotates without friction about a...Ch. 10 - A 12.0-kg box resting on a horizontal,...Ch. 10 - A 2.20-kg hoop 1.20 m in diameter is rolling to...Ch. 10 - BIO Gymnastics. We can roughly model a gymnastic...Ch. 10 - What fraction of the total kinetic energy is...Ch. 10 - A siring is wrapped several times around the rim...Ch. 10 - A solid ball is released from rest and slides down...Ch. 10 - A hollow, spherical shell with mass 2.00 kg rolls...Ch. 10 - A 392-N wheel comes off a moving truck and rolls...Ch. 10 - A uniform marble rolls down a symmetrical bowl,...Ch. 10 - A thin, light string is wrapped around the outer...Ch. 10 - A Ball Rolling Uphill. A bowling ball rolls...Ch. 10 - A size-5 soccer ball of diameter 22.6 cm and mass...Ch. 10 - A size-5 soccer ball of diameter 22.6 cm and mass...Ch. 10 - A playground merry-go-round has radius 2.40 m and...Ch. 10 - An engine delivers 175 hp to an aircraft propeller...Ch. 10 - A 2.80-kg grinding wheel is in the form of a solid...Ch. 10 - An electric motor consumes 9.00 kJ of electrical...Ch. 10 - (a) Compute the torque developed by an industrial...Ch. 10 - An airplane propeller is 2.08 m in length (from...Ch. 10 - A 2.00-kg rock has a horizontal velocity of...Ch. 10 - A woman with mass 50 kg is standing on the rim of...Ch. 10 - Find the magnitude of the angular momentum of the...Ch. 10 - (a) Calculate the magnitude of the angular...Ch. 10 - CALC A hollow, thin-walled sphere of mass 12.0 kg...Ch. 10 - CP A small block on a frictionless, horizontal...Ch. 10 - Prob. 10.41ECh. 10 - A diver comes off a board with arms straight up...Ch. 10 - The Spinning Figure Skater. The outstretched hands...Ch. 10 - A solid wood door 1.00 m wide and 2.00 m high is...Ch. 10 - A large wooden turntable in the shape of a flat...Ch. 10 - Asteroid Collision! Suppose that an asteroid...Ch. 10 - Prob. 10.47ECh. 10 - A thin uniform rod has a length of 0.500 m and is...Ch. 10 - A thin, uniform metal bar. 2.00 m long and...Ch. 10 - A uniform. 4.5-kg, square, solid wooden gate 1.5 m...Ch. 10 - The rotor (flywheel) of a loy gyroscope has mass...Ch. 10 - A Gyroscope on the Moon. A certain gyroscope...Ch. 10 - Stabilization of the Hubble Space Telescope. The...Ch. 10 - A 50.0-kg grindstone is a solid disk 0.520 m in...Ch. 10 - 10.55A grindstone in the shape of a solid disk...Ch. 10 - A uniform, 8.40-kg, spherical shell 50.0 cm in...Ch. 10 - A thin, uniform. 3.80-kg bar, 80.0 cm long, has...Ch. 10 - You are designing a simple elevator system for an...Ch. 10 - The Atwoods Machine. Figure P10.59 illustrates an...Ch. 10 - The mechanism shown in Fig. P10.60 is used to...Ch. 10 - A large 16.0-kg roll of paper with radius R = 18.0...Ch. 10 - A block with mass m = 5.00 kg slides down a...Ch. 10 - Two metal disks, one with radius R1 = 2.50 cm and...Ch. 10 - A lawn roller in the form of a thin-walled, hollow...Ch. 10 - Two weights are connected by a very light,...Ch. 10 - You complain about fire safety to the landlord of...Ch. 10 - The Yo-yo. A yo-yo is made from two uniform disks,...Ch. 10 - CP A thin-walled, hollow spherical shell of mass m...Ch. 10 - A basketball (which can be closely modeled as a...Ch. 10 - CP A solid uniform ball rolls without slipping up...Ch. 10 - Rolling Stones. A solid, uniform, spherical...Ch. 10 - You are designing a system for moving aluminum...Ch. 10 - A 42.0-cm-diameter wheel, consisting of a rim and...Ch. 10 - A uniform, 0.0300-kg rod of length 0.400 in...Ch. 10 - A uniform solid cylinder with mass M and radius 2R...Ch. 10 - Tarzan and Jane in the 21st Century. Tarzan has...Ch. 10 - A 5.00-kg ball is dropped from a height of 12.0 m...Ch. 10 - The solid wood door of a gymnasium is 1.00 m wide...Ch. 10 - A uniform rod of length L rests on a friction less...Ch. 10 - CP A large turntable with radius 6.00 m rotates...Ch. 10 - In your job as a mechanical engineer you are...Ch. 10 - A local ice hockey team has asked you to design an...Ch. 10 - You are designing a slide for a water park. In a...Ch. 10 - Neutron Star Glitches. Occasionally, a rotating...Ch. 10 - A 500.0-g bird is flying horizontally at 2.25 m/s,...Ch. 10 - CP A small block with mass 0.130 kg is attached to...Ch. 10 - A 55-kg runner runs around the edge of a...Ch. 10 - DATA The V6 engine in a 2014 Chevrolet Silverado...Ch. 10 - DATA You have one object of each of these shapes,...Ch. 10 - DATA You are testing a small flywheel (radius...Ch. 10 - CALC A block with mass m is revolving with linear...Ch. 10 - When an object is rolling without slipping, the...Ch. 10 - A demonstration gyroscope wheel is constructed by...Ch. 10 - The moment of inertia of the empty turntable is...Ch. 10 - While the turntable is being accelerated, the...Ch. 10 - A doubling of the torque produces a greater...Ch. 10 - If the bodys center of mass were not placed on the...
Additional Science Textbook Solutions
Find more solutions based on key concepts
20. lf you make multiple measurements of your height, you are likely to find that the results vary by nearly ha...
College Physics: A Strategic Approach (3rd Edition)
The same AC voltage appears across a capacitor and a resistor, and the same rms current flows in each. Is the p...
Essential University Physics (3rd Edition)
The pV-diagram of the Carnot cycle.
Sears And Zemansky's University Physics With Modern Physics
the difference between average speed and constant speed.
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
Using the definitions in Eqs. 1.1 and 1.4, and appropriate diagrams, show that the dot product and cross produc...
Introduction to Electrodynamics
Write each number in decimal form.
29. 6.93 × 101
Applied Physics (11th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A hydroelectric dam uses the energy of a waterfall to turn a turbine to generate electric energy with an efficiency of 53%. If the waterfall is 32 m high and 147 kg of water falls every minute, what is the maximum speed the 57 kg turbine can spin in one minute?arrow_forwardA 30-m chain with mass density 9 kg/m is initially coiled on the ground. How much work is performed in lifting the chain so that it is fully extended and one end touches the ground? Assume g 9.8 m/s². (Use decimal notation. Give your answer as a whole or exact number.)arrow_forwardSomeone is stuck at the top of a tower, and is very thirsty. A heroic dog, weighing 40lbs, carries a bucket of water, weighing 5 lbs, up a helical staircase that encircles a tower with a radius of 15ft. The tower is 60ft high and the dog makes exactly three complete revolutions climbing to the top. Unfortunately the bucket leaks water at a steady rate, and during the ascent, 1lb of water leaks out. How much work is done by the dog against gravity?arrow_forward
- In the figure, a 2.51 g ice flake is released from the edge of a hemispherical bowl whose radius r is 11.3 cm. The flake-bowl contact is frictionless. (a) How much work is done on the flake by the gravitational force during the flake's descent to the bottom of the bowl? (b) What is the change in the potential energy of the flake-Earth system during that descent? (c) If that potential energy is taken to be zero at the bottom of the bowl, what is its value when the flake is released? (d) If, instead, the potential energy is taken to be zero at the release point, what is its value when the flake reaches the bottom of the bowl? Ice flakearrow_forwardA 15 kg skip attached to a steel rope on a crane is used to hoist bricks from the ground to the top of a construction site. The steel rope is wound onto a lifting drum with a diameter of 700 mm and rotational frequency of 54 revolutions per minute. The lifting drum is situated on the top floor. Calculate the efficiency of the lifting generator, if the electric motor power of 9000 W is needed to drive the loaded skip.arrow_forwardIn the figure, a 2.30 g ice flake is released from the edge of a hemispherical bowl whose radius r is 25.1 cm. The flake-bowl contact is frictionless. (a) How much work is done on the flake by the gravitational force during the flake's descent to the bottom of the bowl? (b) What is the change in the potential energy of the flake-Earth system during that descent? (c) If that potential energy is taken to be zero at the bottom of the bowl, what is its value when the flake is released? (d) If, instead, the potential energy is taken to be zero at the release point, what is its value when the flake reaches the bottom of the bowl? Ice flake (a) Number i Units (b) Number i Units (c) Number i Units (d) Number i Unitsarrow_forward
- In the figure, a 2.12g ice flake is released from the edge of a hemispherical bowl whose radius r is 16.2 cm. The flake-bowl contact is frictionless. (a) How much work is done on the flake by the gravitational force during the flake's descent to the bottom of the bowl? (b) What is the change in the potential energy of the flake-Earth system during that descent? (c) If that potential energy is taken to be zero at the bottom of the bowl, what is its value when the flake is released? (d) If, instead, the potential energy is taken to be zero at the release point, what is its value when the flake reaches the bottom of the bowl? Ice flake- (a) Number i Units (b) Number Units (c) Number i Units (d) Number Units > >arrow_forwardIt is difficult to move a cycle along the road with its brakes on. Why?arrow_forwardThe engine of a car, where properly geared, can cause its wheels to spin, but this can only happen at low road speeds. How is this best explained? The product of the output power and the speed of the car is greater than the force of friction between the tyres and the road The road friction divided by the car output power is greater than the speed of the car The ratio of output power to the engine torque is greater than the speed of the car The output power from a car engine is greater at lower road speeds The product of the speed of the car and the output power is less than the force of friction between the tyres and the road The car output power divided by the speed of the car is greater than the force of friction between tyres and the roadarrow_forward
- A steel rod 250 mm long and 200 mm in diameter is being reduced to 190 mm in diameter all over its length in one travel. The machine spindle rotates at 500 rpm, whereas the tool is moving at an axial feed of 0.5 mm/rev; calculate the following: a. Material removal rate (mm3/min) b. Consumed gross power in Nm/s if cutting force is 477.5N and mechanical efficiency is 90% c. Cutting timearrow_forwardI am not sure how to work this problem. The problem gives the answers but does not show how to work the problem.arrow_forwardA smooth circular hoop with a radius of 0.900 m is placed flat on the floor. A 0.475-kg particle slides around the inside edge of the hoop. The particle is given an initial speed of 9.00 m/s. After one revolution, its speed has dropped to 5.00 m/s because of friction with the floor. (a) Find the energy transformed from mechanical to internal in the particle-hoop-floor system as a result of friction in one revolution. 13.3 (b) What is the total number of revolutions the particle makes before stopping? Assume the friction force remains constant during the entire motion. 1 Your response differs from the correct answer by more than 10%. Double check your calculations. revarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Work-Energy Theorem | Physics Animation; Author: EarthPen;https://www.youtube.com/watch?v=GSTW7Mlaoas;License: Standard YouTube License, CC-BY