EBK AUTOMOTIVE TECHNOLOGY
5th Edition
ISBN: 9780100659841
Author: Halderman
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Question
Chapter 1, Problem 8CQ
To determine
The component that is needed by a service technician to retrieve stored diagnostic trouble codes.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Complete the following statement about scan tool using the following words.Words:
Activate, Actuators, Always, Computer, Correct, Diagnose, Diagnosing, DTC’s, Procedures, Scan, Management, System
A __________ tool and/or a special electronic tester is used to __________ most engine __________system. These can only retrieve __________; they may also be able to __________ various__________ in the system. The exact __________ and available data from the vehicle’s __________will vary with manufacturer and the __________ found on the vehicle. __________ refer to the__________ service information when __________ engine management systems.
Which of the following statements is not true?
a. DTCs that will not affect emissions will never illuminate the MIL.
b. An active or current DTC represents a fault that was detected and occurred during two trips.
c. When a two-trip fault is detected for the second time, a DTC is stored as a pending code.
d. There are some DTCs that will set in one trip
The only thing that can keep you safe consistently is __________________
a.
Obeying all warning signs
b.
Your supervisor
c.
Personal protective equipment (PPE)
d.
Your attitude
Chapter 1 Solutions
EBK AUTOMOTIVE TECHNOLOGY
Ch. 1 - In 1900, what was the most produced vehicle...Ch. 1 - What parts are included in the vehicle chassis?Ch. 1 - Why were early engines called flat heads?Ch. 1 - Prob. 4RQCh. 1 - The powertrain consists of what components?Ch. 1 - Prob. 6RQCh. 1 - Prob. 1CQCh. 1 - Prob. 2CQCh. 1 - Which component is not part of the chassis system?...Ch. 1 - Early engines were called flat head design because...
Knowledge Booster
Similar questions
- H.b- When you're first starting a PM program, and you want to check motor starter and contactor contacts,how often should you perform a PM inspection on these devices?A. Every two monthsB. Every six monthsC. Every yearD. Every month c.b. Which one of the following isn’t a goal of a PM program?A. Limit downtimeB. Save a company money on maintenance so that the cost of its products stays competitiveC. Keep a machine running within its specificationsD. Use fewer repair parts and less time to install those parts c.c. Which of the following tasks is an uptime PM task that can be performed while the machine is runningduring production?A. Checking the motor starter contacts for burned and pitted areasB. Checking for excess noise or vibration on the machineC. Checking the condition of the couplingD. Tightening electrical connectionsarrow_forwardWhich of the following lab scope controls must be set when trying to observe how long an event takes place? Intensity Vertical Horizontal Triggerarrow_forwardWhile discussing diagnostic procedures: Technician A says that after the visual inspection has been performed, the DTCs should be cleared from the memory of the PCM. Technician B says that serial data can be helpful when there are no DTCs but there is a fault in the system. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- List the four ways that individual components can be checked.arrow_forwardLockout locks: Can be used to lock tool boxes, storage sheds, etc. b. Can be used only for lockout purposes. Are provided by the equipment manufacturer. d. a. C. Must be bright orange in color. Authorized employees must be trained: To recognize hazardous energy sources, and to know the type and magnitude of the hazardous energy sources. b. a. To perform the lockout/tagout procedure. C. When an audit shows deficiencies with the procedure. d. All of the above. When authorized employees perform a shutdown they must: a. Notify all affected employees that they are starting a lockout procedure, b. Locate all energy sources that power the equipment. Follow the procedures to shut down each machine. d. All of the above. с. If several people are needed to work on a piece of equipment: a. The first worker to arrive to the job is the one who applies the locks. b. Their supervisor is the only one who needs to apply a lock. c. Each worker must apply his or her own lock. d. The person who will be the…arrow_forwardWhich of the following is not a true of group lockout or tagout? a. Each employee working on the equipment is an authorized employee b. A supervisor may attach a lock for an entire work crew. c. Each person working on the equipment must have a lock or tag d. A supervisor should be the first or last person to attach a lock or tagarrow_forward
- Metrology Lab Block gauges exp. sheetarrow_forwardConduct a lock-out and tag-out activity in the oil rig to repair the drilling equipment and well-logging instrument. Identify the specific steps that you will make for the above case. Note: type writting don't write with hand writtingarrow_forwardSuccessful re-engineering eliminate much monitoring checking, waiting, etc leaving more time for doing productive work . True or falsearrow_forward
- Which type of dewpoint analyzer relies on measuring the electrical conductivity of a hygroscopic material? Nuclear solids moisture analyzer NIR moisture analyzer Microwave moisture analyzer Dew cellarrow_forwardTechnician A says vehicle inspection pits allow access to the vehicle's underside without using a hoist or jack. Technician B says that vehicle inspection pits only need to be covered when a vehicle is over the top of them. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor B ge Next page quiz/attempt.pftp?attempt-4403533&cmid%-D3426318&page=9#arrow_forwardList five of engineering controls and administrative controls to reduce the hazard of the car steering wheelarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning