H.b- When you're first starting a PM program, and you want to check motor starter and contactor contacts, how often should you perform a PM inspection on these devices? A. Every two months B. Every six months C. Every year D. Every month c.b. Which one of the following isn’t a goal of a PM program? A. Limit downtime B. Save a company money on maintenance so that the cost of its products stays competitive C. Keep a machine running within its specifications D. Use fewer repair parts and less time to install those parts c.c. Which of the following tasks is an uptime PM task that can be performed while the machine is running during production? A. Checking the motor starter contacts for burned and pitted areas B. Checking for excess noise or vibration on the machine C. Checking the condition of the coupling D. Tightening electrical connections

H.b- When you're first starting a PM program, and you want to check motor starter and contactor contacts, how often should you perform a PM inspection on these devices? A. Every two months B. Every six months C. Every year D. Every month c.b. Which one of the following isn’t a goal of a PM program? A. Limit downtime B. Save a company money on maintenance so that the cost of its products stays competitive C. Keep a machine running within its specifications D. Use fewer repair parts and less time to install those parts c.c. Which of the following tasks is an uptime PM task that can be performed while the machine is running during production? A. Checking the motor starter contacts for burned and pitted areas B. Checking for excess noise or vibration on the machine C. Checking the condition of the coupling D. Tightening electrical connections

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter2: Workplace Skills

Section: Chapter Questions

Problem 1RQ: Which of the following is not a recommended step for accurate diagnosis of a problem? Gather as much...

See similar textbooks

Similar questions

19.a. A machine has a coupling that fails once every year and a half. What type of PM task can be created tomake sure that this coupling won’t fail on uptime?A. An electrical PM every six monthsB. An operator PM every yearC. A lubricator PM every eight monthsD. A mechanical PM every year19.b. If mission-critical equipment fails after a PM program is initiated, the best action is toA. install permanent employees to monitor the equipment until the proper maintenance schedule can be created.B. become a critic of the program until changes are made.C. modify the inspection and maintenance schedules to lower the failures.D. double the inspection schedule.19.c. Who is often overlooked as an important source of information and should be asked about PMmaintenance tasks in the program?A. Purchasing departmentB. Computer specialistsC. Machine operatorsD. outside contractors
"Vehicle 1. Explain how each of these safety features is designed to protect you. a. anti-lock braking systems b. crumple zones c. side-impact beams d. seat belts 2. How many times more likely are people who don't wear seat belts to be injured than people who do wear seat belts? 3. Study Figure 13.10. What is the relationship between seat belt use and occupant fatalities? 4. Name three items you should regularly maintain on your vehicle to ensure your safety. CHECK Check your answers on pages 101 and 102 of the Appendix. Science 24 Module 4 • Section
Root cause analysis (RCA) is a problem solving technique to find the actual cause of the problems which usually lie underneath the visible symptoms. It requires thorough analysis steps and investigation to find the actual cause. 5 WHY analysis is one of the commonly use RCA technique. Complete the Table 2 using given possible causes listed below in correct sequences. Problem: The machine at the production suddenly stopped The circuit was overloaded, causing the fuse to blow. Bearing locked up because insufficient Jubrication 2 WHY the circuit overloaded? 3 WHY was the insufficient lubricant? 5 WHY is the pump clogged with metal? The pump strainer was broken. Solution : WHY the machine stopped? Hire new technician WHY the pump circulate oils? WHY technician did not perform inspection? Pump in good condition Replace a new strainer with correct size. WHY the pump circulate less oil? Pump clogged with metal shaving. Pump not circulating enough oil WHY the operator stopped the machine? New…
7.a. A conveyor that uses a line shaft to turn the rollers should have the line shaft bearings checked on a PMinspection everyA. year.B. six months.C. four weeks.7.b. If you find a bad nicad cell in a battery pack, you shouldA. solder in a new cell.B. replace the battery pack.C. add a new cell in parallel.D. shock the cell with a short pulse of high voltage.
Which of the following statements is incorrect? a. As a result, molecules will flow in one of six potential ways. As a result, it is reasonable to predict that one-sixth of it will move in the positive direction.b. Flux is the rate at which something is transported per unit area of space.c. Flux can occur even if there is no driving forced.Initially, the flow for transport processes is nonlinear, but over a period of time, the flux becomes linear.
Technician A says vehicle inspection pits allow access to the vehicle's underside without using a hoist or jack. Technician B says that vehicle inspection pits only need to be covered when a vehicle is over the top of them. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor B ge Next page quiz/attempt.pftp?attempt-4403533&cmid%-D3426318&page=9#
What is a Thermocouple: Select one: a. A Thermocouple is a temperature sensor that uses a small length of platinum wire that is trimmed to have particular resistance at specific temperature. b. A Thermocouple is a temperature sensor that consists of two wires of similar metals joined at one end. C. A Thermocouple is a type of resistor whose resistance varies with temperature. d. A Thermocouple is a temperature sensor that consists of two conducting wires of dissimilar metals joined at one end.
A furnace thermostat has a constant failure rate of one failure per 25 months and a mean time to repair of four hours., a) What is the thermostate reliablity after 12 months? After 24 months? After 36 months? b) What is the availablity? c) Should a design team try to streamline the repair process to reduce the MTTR? Explain. Does the location of the furnace matter?
Conduct a lock-out and tag-out activity in the oil rig to repair the drilling equipment and well-logging instrument. Identify the specific steps that you will make for the above case. Note: type writting don't write with hand writting
Which one of the below statements is mostly NOT correct about in creation of detailed design of component? The selection of material is based on what is required to performance the function. The tolerance is determined by the function, not the preference of designer or manufacture. In the selection of manufacturing processes, the number of components to be manufactured needs to be considered, as the capital investment needs to be considered. I do not need to show or prove the component is working: such how much electricity is generated in power panel, how much braking force is generated in by the brake disc, or how much the force the component in suspension is subjected?
10) Pollution and noise control is the primary maintenance function. Select one: True False
1. What is the difference between corrective maintenance and preventive maintenance ?