Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 24, Problem 7ASRQ
While discussing diagnostic procedures: Technician A says that after the visual inspection has been performed, the DTCs should be cleared from the memory of the PCM. Technician B says that serial data can be helpful when there are no DTCs but there is a fault in the system. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Which of the following statements is not true?
a. DTCs that will not affect emissions will never illuminate the MIL.
b. An active or current DTC represents a fault that was detected and occurred during two trips.
c. When a two-trip fault is detected for the second time, a DTC is stored as a pending code.
d. There are some DTCs that will set in one trip
Which of the following statements is
TRUE on the enforcement of IPRS?
The accused infringer must prove
that infringement has not occurred.
The IP owner does not need to
provide evidence of IP ownership
IPRS are automatically enforced by
the State
A vehicle with a direct TPMS is brought into a shop with all sensors failing to read any pressure at all. Technician A says it’s likely that all 4 sensors died at once. Technician B says it may be due to a damaged or faulty TPMS antenna. Who is correct?
Technician A
Technician B
Both Technician A and B
Neither Technician A or B
Chapter 24 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 24 - Describe the difference between an open- and a...Ch. 24 - Explain the use and importance of system strategy...Ch. 24 - Describe an OBD II warm-up cycle.Ch. 24 - Explain the trip and drive cycle in an OBD II...Ch. 24 - Describe how engine misfire is detected in an OBD...Ch. 24 - Describe the purpose of having both upstream and...Ch. 24 - Briefly describe the monitors in an OBD II system.Ch. 24 - Type B engine misfires are excessive if the...Ch. 24 - The monitor system checks the action of the can...Ch. 24 - The monitor system has a(n) and test to check the...
Ch. 24 - The fuel monitor checks fuel trim and fuel trim.Ch. 24 - Which sensor is used for misfire monitoring on OBD...Ch. 24 - Which of the following statements is not true?...Ch. 24 - A computer is capable of doing all of the...Ch. 24 - Which of the following memory circuits is used to...Ch. 24 - Technician A says that the oxygen sensor provides...Ch. 24 - While discussing OBD II systems: Technician A says...Ch. 24 - While discussing the catalyst efficiency monitor:...Ch. 24 - While discussing monitoring systems: Technician A...Ch. 24 - While discussing the comprehensive monitoring...Ch. 24 - Prob. 6ASRQCh. 24 - While discussing diagnostic procedures: Technician...Ch. 24 - Technician A says that the enable criteria are the...Ch. 24 - While discussing PCM monitor tests: Technician A...Ch. 24 - While discussing the misfire monitor: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing the results of a load test: Technician A says that if a battery fails a load test but the voltage rises above 12.4 volts when the load is removed, the battery should be replaced. Technician B says that if a battery fails a load test but the voltage rises above 12.4 volts when the load is removed, the battery is able to hold a charge. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A lab scope is a visual voltmeter that shows voltage over a period of time.arrow_forwardWhile measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- True or False? The same information available in service manuals and bulletins may also be available electronically on DVDs and the Internet.arrow_forwardTechnician A uses a testlight to detect resistance. Technician B uses a jumper wire to test circuit breakers, relays, and lights. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A bad ground can cause an increase in the reference voltage to a sensor.arrow_forward
- Technician A uses a high-impedance testlight on the high-voltage systems in hybrid vehicles. Technician B uses only CAT-III test instruments to check high- voltage systems. Who is correct? Technician A Both A and B Technician B Neither A nor Barrow_forwardTechnician A says that before a battery is removed, a memory' saver ought to be installed. Technician B says that before a battery is removed, the positive cable should be disconnected and the area around the battery should be cleaned. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardMaterials testing used to detect surface flaws and flaws close to the surface * O Dye penetrant inspection Magnetic particle inspection O Ultrasonic testing O Eddy current testingarrow_forward
- Technician A says that some types of voltage sensors provide input to the computer by modifying or controlling a constant, predetermined voltage signal. Technician B says that a coolant temperature sensor is a voltage-generating sensor. Who is correct?arrow_forwardtrue or False? The computer in most late-model vehicles must undergo a relearn or initialization procedure after the vehicle's battery has been disconnected and reconnected?arrow_forwardBy monitoring the condition of the machine, preventive maintenance can not be performed to increase the operational life of a machine. Select one: True Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License