You were performing a compression test on two different materials. The compression was done in y-direction on both of the samples in an unconfined condition. Sample A had an original width of 5 cm length of 12 cm, and it was compressed by 15%. Sample B had an original width of 2 cm and original length of 12 cm, and it was compressed by 17.5%. Which sample had the higher strain?

You were performing a compression test on two different materials. The compression was done in y-direction on both of the samples in an unconfined condition. Sample A had an original width of 5 cm length of 12 cm, and it was compressed by 15%. Sample B had an original width of 2 cm and original length of 12 cm, and it was compressed by 17.5%. Which sample had the higher strain?

Biomedical Instrumentation Systems

1st Edition

ISBN:9781133478294

Author:Chatterjee

Publisher:Chatterjee

Chapter15: Instrumentation In Medical Imaging

Section: Chapter Questions

Problem 7P

See similar textbooks

Similar questions

It is possible to make a perfectly precise measurement?Explain.
You want to set up a 1:10 dilution series, so that you can plate a 10-1, 10-2, and a 10-3dilution; however, you only have access to two9 ml dilution blanks. Explain how you could accomplish this task with only two blanks.
You have a stock solution of 40% hydrogen peroxide. You need to make several dilutions for a calibration curve. Calculate how much volume of the stock hydrogen peroxide you need to make 50 mL of 11% hydrogen peroxide.
You are to prepare capsules that contain 0.125 g of a drug. You have four partial containers of medicatiog, which weigh 3.2 g, 1.784 g, 2.46 g, and 5.87 g. Assume you have weighed each of the four containers with the same scale, and the accuracy is known to the hundredth gram. a Which amount will need to be rounded? b. Which amount is not as accurate as it should be? c. What is the amount of the medication that will be left over after making as many 0.125 g capsules as possible?
Śwabbing means pulling fluid from the hole on the way out with the test tool could cause a kick, which could result in a blowout leading to injuries and deaths. Select one: True False
If you had a cell suspension of 2.5 x 10^4 cells/mL and plated 100uL into each well (4 wells), how many cells were added per well?
Can you explain how to find the answer and the calculation?
You have a sample – sample 1 - that has a concentration (✗) particles. From this you take 1 mL and add it to 99 mL water to create sample 2. You then take 1 mL of sample 2 and place it in 99 mL of water to create sample 3. And lastly, you take 1 mL of sample 3 and add it to 9 mL of water to create sample 4. What is the final dilution factor in sample 4? You may use drawings if it helps you understand and explain, though not necessary.
Mary Jo prepared a series of diluted samples by taking 1 mL of sample and adding it to 4 mLs of diluent. She then diluted the sample further by adding 1 mL of diluted sample to 19 mLs of diluent. What is the final dilution factor ?
Why is the accuracy of the calibration curve so critical?
To prepare a vaginal irrigation, a nurse uses 3 tsp of vinegar and 1.5 L of water. a. How many ml of vinegar should she use? b. If she prepares a solution using only 500 ml of water, how many ml of vinegar should she use?
The replicate results (mg/L) obtained from calcium determination of a blood sample using atomic absorption spectrophotometry (AAS) and a new colorimetric method were as following: AAS : 11.2, 11.2, 10.6, 11.2, 9.7 and 10.0 Colorimetric : 9.2, 10.5, 9.7, 11.5, 11.6, 9.3, 10.1 and 11.2 Determine whether the mean of both methods have a significant difference at 95% confidence level.