Would a 0.010" or 0.031" tool nose radius be stronger

Q: Explain the process of aligning a hole working tool with the center of the workpiece.

A: The alignment of hole making tool with the center of work on the lathe machine . The workpiece is…

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: Find the commercial tap drill size for 1⁄2”-20

A: given: Find the commercial tap drill size for 1⁄2”-20 NF bolt.

Q: A close-coiled helical spring is manufactured from 7-mm-diameter steel wire with 45 coils. The mean…

A:

Q: What is the tool length offset? How is the tool length offset measured

A:

Q: 1) Orthogonal Cutting: In an orthogonal cutting test on mild steel, the following results are…

A:

Q: 44. Bigger diameter end mill cutting tool is preferred during milling operation. Select one: True O…

A: In general, milling is a machining process in which the rotary motion of the cutter is used to…

Q: 18 A typical lathe bed is made of a low grade cast iron. Select one: True False

A: We have to find  true /false A typical lathe bed is made of a low grade cast iron.

Q: the reading of this tool is

A:

Q: dentify the side rake angle (in degrees), from the following single point  tool signature…

A:

Q: Through hole of 12 mm diameter is to be drilled in a steel plate of 20 mm thickness, drilled spindle…

A: Given: The diameter of hole is d=12 mm. The thickness of steel plate is t=20 mm. The drilled…

Q: Identify the Lathe operation, performed without the tool moving perpendicular to the aXIS Knurling…

A: Option a is correct.

Q: How did you find out the angle was 90 and how can you find that for other problems?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: "A face milling operation is performed to finish the top surface of a steel rectangular workpiece 11…

A:

Q: 3. (a) In the set-up shown, if the support columns are removed, what will happen to the see-saw?…

A:

Q: Refer to drawing 21A044, How many full threads will the fine tapped hole contain at minimum depth…

A: A standard thread form and series, along with allowances, tolerances, and designations, for screw…

Q: Determine friction angle for metal cutting operation

A: To find Friction angle.

Q: A strip of thickness 40 mm is to be rolled to a thickness 20 mm using a two-high mill having a rolls…

A: Given data,  H1= 40 mm  H2 = 20 mm  D= 200 mm

Q: 4. Name 4 types of cutting tool wears and explain what problem can happen if the depth of cut is…

A: Tool wear : It is breakdown and gradual failure of  cutting tool due to regular operation on…

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: Describe at least two methods and the equipment used to measure tool length and radii on/for a mill.…

A: We have to measure tool length and radii which can be done by various techniques and equipment. The…

Q: 11. Orientation of two circles with the same center. _ 12. Press fitting a pin/ shaft to a hole…

A: 11) Orientation of two circles with same center.  Answer: Concentric Circles   12) Press fitting a…

Q: If the ratio of torque to bending moment on a shaft is 0.33, what would be the ratio of equivalent…

A: According to the given dataWe need to find

Q: The required shape of the Tipped type tool is made by forging before hardening and grinding high…

A: The process that is used to provide the required shape is basically the powdered metallurgy process.…

Q: Read the sentences given below and Identify the wrong statement.   Sentence 1. The advantage of an…

A: Independent chuck works as the holding device for the workpiece. It contains 4 independent jaws that…

Q: I need help with this.

A: Note:We’ll answer the first question since the exact one wasn’tspecified. Please submit a new…

Q: If the diameter with tolerance of the hole is 2.6 ±0.1 mm, which of the following is the safe…

A: Diameter with tolerance the hole =2.6 ± 0.1 mm   To find: Safe diameter and tolerance of the shaft…

Q: Identify the nose radius(in mm) from the following single point tool signature  2-3-5-8-12-15-1.…

A:

Q: what size tools would you use to make this hole on a lathe?

A: In this problem, it is asking what will be the tool size to make a hole on lathe.

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the…

A:

Q: Identify and explain the method of milling process in which the stresses on the teeth is maximum at…

A: The milling process in which the stress on the teeth is maximum at the end of the cut is the up…

Q: sketch write short notes on any two types of rolling bearings

A:

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an…

A: for solution refer below images.

Q: What size of hole should be bored before cutting a 7/8 in. internal thread having 9 TPI and 12 mm.…

A: Given data as per the question Internal thread =7/8 in TPI =9 Number of pitch =1.75

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: . Circle the correct section view out of the three possibilities. Would a half section been…

A: The section 2 is correct. The reason is mentioned below. First look at the cutting plane, it is…

Q: What is the cutting speed of a material with a radius of 40 mm and a speed of 1000 rpm?

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.