Through hole of 12 mm diameter is to be drilled in a steel plate of 20 mm thickness, drilled spindle speed is 20 m/min, feed 0.25 mm/rev and drill point angle is 120°, the amount of material removed at the first 10 sec after full engagement of drill will be mm /sec. (a) 2300, (b) 2400, (c) 2500, (d) 2600, (e) 2700

Through hole of 12 mm diameter is to be drilled in a steel plate of 20 mm thickness, drilled spindle speed is 20 m/min, feed 0.25 mm/rev and drill point angle is 120°, the amount of material removed at the first 10 sec after full engagement of drill will be mm /sec. (a) 2300, (b) 2400, (c) 2500, (d) 2600, (e) 2700

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter4: Drill Press

Section4.1: Introduction To The Drill Press

Problem 5RQ: Briefly describe a gang drill press and its benefit.

See similar textbooks

Similar questions

Handwritten solution recommended. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
Please solve it correctly , Don't Use Ai tool. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
A twin-spindle drill simultaneously drills one ½-in hole and one ¾" through a 1" wide work piece. Both holes are twist drill with 118° point angles. cutting speed for material is 230 ft/min. The rotation speed of each spindle can be configured individually. The feed rate of both holes must be set to the same value, since both spindles go down at the same speed. The forward speed is set in such a way that the speed total metal removal does not exceed 1.50 in3 /min. Determine: a) the velocity maximum feedrate (in/min) that can be used, b) the individual feedrates (in/rev) that result in each hole and c) the time required to drill the holes.
Briefly describe a gang drill press and its benefit.
A o 20 mm through hole is to be drilled in a 30 mm thick plate using a double fluted, 120° lip angle drill The drill tip is at a distance of 3 mm from the plate surface when cutting is started and an over travel of 2 mm is recommended as a margin to ensure drilling through the full thickness of the plate. If the drill rotates at 500 rev/min and the feed per tooth is 0.01 mm,find the machining time of the operation.
The outline of the part in the Figure below is to be profile milled using a 20- mm diameter end mill with two teeth. The part is 10 mm thick. The cutting speed = 125 m/min and feed = 0.10 mm/tooth. The part is also to be drilled with a drill size of 10 mm corresponds to T01 with a cutting speed =75 mm/min and feed = 0.08 mm/rev. The two holes pass completely through the part. 30 rad. 125.75 10 dia., 2 holes Write the part program (G & M code program) for the required machining processes. Use absolute programming with the lower left 25 corner of the part as the origin in the x-y axis system. 150 (All dimensions are in mm.) 25 50 75 35 deg.
A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the feed is 0.005 in / rev, what is the MRR? What is the MRR if the drill diameter is doubled? What is the power required in the drill if the material is an annealed AISI 1080?
A drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and feed = 0.20 mm/rev. The 18-mm-diameter twist drill has a point angle of 120°. Determine the following once the drill reaches full diameter: a. the machining time and, b. the metal removal rate Equation used Tm TD₂L fv
A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 48 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.1 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 48.8 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm ( (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
The part in Figure 1 is to be drilled on a turret-type drill press. The part is 15.0 mm thick. Threedrill sizes will be used: 8 mm, 10 mm, and 12 mm, which are to be specified in the part programby tool turret positions TO1, T02, and T03. All tooling is high speed steel. Cutting speed = 75mm/min and feed = 0.08 mm/rev. Use the lower-left corner of the part as the origin in the x-y axissystem. Write the part program in the word address format using absolute positioning.