Which of the sentences is WRONG concerning the following code?Ladder logic programTimer_Sw36Status_Timer.EN36Status_Timer.TT36Status_Timer.DNHEO a.O b.O d.TON-TIMER ON DELAYTimerPresetAccume.None of the choices(EN)10000-(ON)5000-Status_TimerEN PL-(-TT_PLDN_PLO c. Once the Timer_Sw is ON for 10 seconds, the light DN_PL is ONWhenever the timer accumulator equals 10000, the done bit is turned ONThe light TT_PL will be ON whenever Timer_Sw is ONThe light EN_PL will be ON whenever Timer_Sw is ON

Answered: Image /qna-images/answer/471fbe1c-690b-41a5-8e0c-8a68ea8db8a3.jpg

Which of the sentences is WRONG concerning the following code? Ladder logic program Timer_Sw 36 Status_Timer.EN 36 Status_Timer.TT 36 Status_Timer.DN H O a. None of the choices O b. 0 c. TON TIMER ON DELAY Timer Preset Accum O d. Status_Timer 10000 (DN) 5000- EN_PL TT_PL DN_PL Whenever the timer accumulator equals 10000, the done bit is turned ON Once the Timer_Sw is ON for 10 seconds, the light DN_PL is ON The light TT_PL will be ON whenever Timer_Sw is ON

Which of the sentences is WRONG concerning the following code? Ladder logic program Timer_Sw 36 Status_Timer.EN 36 Status_Timer.TT 36 Status_Timer.DN H O a. None of the choices O b. 0 c. TON TIMER ON DELAY Timer Preset Accum O d. Status_Timer 10000 (DN) 5000- EN_PL TT_PL DN_PL Whenever the timer accumulator equals 10000, the done bit is turned ON Once the Timer_Sw is ON for 10 seconds, the light DN_PL is ON The light TT_PL will be ON whenever Timer_Sw is ON

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is Mealy state machine. Draw the state diagram of sequence 1010 using mealy machine.
Given the below arduino code for a blinking LED: void setup() { int LED = 7 pinMode(LED,OUTPUT); } void loop() { digitalWrite(LED,HIGH); delay(500); digitalWrite(LED,LOW); delay(500); } Modify the code so that the LED is connected to pin 6 and the delay is one second between each blinking. What happened to the led speed blinking when the delay was changed?
21. Which voltage range that is sometimes called a “float" in TTL circuits?
Explain RTD with necessary diagram and equations.
Question 3: A very common application of electromechanical relay logic is motor control circuitry. Here is a ladder diagram for a simple DC motor control, where a momentary pushbutton switch starts the motor, and another pushbutton switch stops the motor: Start Stop CR1 CR1 CR1 Mtr Translate this ladder diagram into point-to-point connections between the following components (shown in the following illustration):
Draw the state diagram to detect sequence 10110. Also write its verilog code
VI. FILL-IN QUESTIONS: 1. Before the TRIAC is triggered on, the voltage across its main terminals is equal to the voltage. 2. When the TRIAC is triggered on, the voltage across its main terminal is about V. 3. Once the TRIAC is conducting, the gate_control the current to flow through the TRIAC. 4. The TRIAC can be turned off by reducing the current through it below its The TRIAC can have_or__terminal voltage and be triggered on by_applied on the gate.
GND int LED - void setup () pinMode (LED, OUTPUT) ; void loop () { digitalWrite(LED,HIGH); delay (1000) ; digitalWrite(LED, LOW) ; delay (1000) ; For the following circuit board, the following code was applied to make the LED blink every one second. 1- If the LED was connected to pin 5 and the delay was 3 seconds. Modify the code to accommodate these changes. 2- How does the LED blinking changes between the two codes? 0O UNO - ARDUINO ANALOO IN
Draw the block diagram and describe the principle of operation of theUPS type inline-interactive.
Explain the meaning and give a practical significance of the unit step signal and ramp signal
Draw a 2x1 multiplexer block diagram.Create the status table. Find the simplest form of circuit output with Karnaugh.Explain the circuit problem that may occur.What should be done to fix the problem?(NEED A NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)
please i need help quickly n 57 The ARDUINO IDE stands for. d a. Integrated development environment out of b. None of these O c. Integrated drive electronics O d. Instructional development environment 58 What does the following ARDUINO command do? analogWrite (9, 63) a. Sets the PWM duty cycle to 25% ut of b. Sets the PWM duty cycle to 75% c. Sets the PWM duty cycle to 50% d. Sets the PWM duty cycle to 30%