0. Six hundred voice channels, each having a bandwidth of 4 kHz, arc multiplexed using USSB subcarrier modulation and the multiplexed signal frequency modulates a carrier. The lowest SSB carrier frequency is 10 kHz and the subcarriers are spaced 4 kHz apart. Assume that each voice signal has the same average power. The channel at 10 kHz has an output signal-to-noise ratio of 60 dB. (a) If (S/N), <30 dB is not acceptable, how many channels in the system are usable? (Assume white noise at the FM receiver input.) (b) If the FDM signal phase modulates the carrier, calculate (S/N), for any channel assuming that the transmitted signal power and noise psd are the same as in the FM case.

0. Six hundred voice channels, each having a bandwidth of 4 kHz, arc multiplexed using USSB subcarrier modulation and the multiplexed signal frequency modulates a carrier. The lowest SSB carrier frequency is 10 kHz and the subcarriers are spaced 4 kHz apart. Assume that each voice signal has the same average power. The channel at 10 kHz has an output signal-to-noise ratio of 60 dB. (a) If (S/N), <30 dB is not acceptable, how many channels in the system are usable? (Assume white noise at the FM receiver input.) (b) If the FDM signal phase modulates the carrier, calculate (S/N), for any channel assuming that the transmitted signal power and noise psd are the same as in the FM case.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Briefly explain what it is Single Sideband Modulation
To obtain SSB mark in single sideband modulation by applying filtering methodare required. The main band mark is band limited between 500 Hz and 1000 Hz, and the mark is at 100 MHzit will be transmitted. Obtaining the exit sign using the necessary stages in stages andexplain by drawing Spectra. Make the necessary calculations.
78. To assure the same accuracy at both 100 Hz and 100 MHz, the signal level into a frequency counter must be A higher at 100 MHz B. higher at 100 Hz C. inductively coupled at 100 MHz and capacitively coupled at 100 Hz D. resistively coupled at 100 MHz and direct coupled at 100 Hz
A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform is shown below. 3.5V- 1V- a) What is the amplitude of the carrier signal? b) c) To achieve 75 percent modulation, what amplitude of the modulating signal is needed? d) Calculate the effective voltage of the AM signal What is the modulation index?
IX. A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform is shown below. a) b) c) d) 5.5V- 2V What is the percentage of modulation? What is the amplitude of the carrier signal? To achieve 75 percent modulation, what amplitude of the modulating signal is needed? Calculate the effective voltage of the AM signal
Five tones are to be transmitted as FDM on a main carrier two of these tones are each 3.3 kHz and modulated SSB on sub-carrier. The other are each at 5.2 kHz and are modulated FM on sub-carrier with modulation index of 6. The base band signal is frequency modulated on main carrier with modulation index of 13. Calculate the transmission bandwidth of the FDM signal. Assuming 1 kHz as a guard band BW=6.412 MHz O BW=8.612 MHz O BW=5.312 MHz BW=7.512 MHz BW=9.712 MHz
A sinusoidally modulated AM waveform is shown below: Determine: a) Peak amplitude of the upper and lower side frequencies. b) Peak amplitude of the unmodulated carrier. The modulation index. The carrier power and the power in the sidebands. The total transmitted power. 3 0 -3 -9 The transmission efficiency. The amplitude of the carrier which must be added or subtracted to attain a modulation index of 0.5. In AM modulation, the modulation index is kept < 100%, why?
1) We need transmission effiency (n) 2) Minimum and Maximum frequency values of the FM signal. ( kHz)
6.a. Which of the following can you accurately measure using an OSA?A. Signal power in a channel onlyB. Spectral width of a channel onlyC. Center wavelength of a signal onlyD. Signal power and spectral width of a channel and center wavelength of a signal6.b. Which instrument should you use to determine the receiver sensitivity threshold during a receiver sensitivity test?A. BER testerB. OTDRC. Reel testerD. Variable optical attenuator
i)Modulation process takes place in the modulator with two injection signals namely data orinformation and carrier. It is a vital step in generating a decent signal for electronic communication.Whenever the carrier is modulated by the information signal, new signals at different frequenciesare generated as part of the process. These new frequencies occur in the frequency spectrum withinthe range of the carrier frequency. Conclude these frequencies and mathematically explain itsgeneration with the help of diagrams. A) Upper sideband and lower broadbandB) Lower sidefloor and upperside floorC) Lower peak and upper peakD) Upper sideband and lower sidebandE) Lower bandwidth and upper gainF) All of the aboveG) None of the above
Q7. Figure Q7 shows a modulated waveform v(t) in millivolts as a function of time t in nanoseconds. 1.5 1.0 0.5 - 0.0 -0.5 -1.0 -1.5 100 200 300 400 500 t/ns Figure Q7: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) Demodulation of this type of waveform is usually performed with an envelope detector. Describe the function of an envelope detector and sketch an example circuit. (g) What requirements on the values of the components of your envelope detector circuit are there for the successful demodulation of the given waveform? (h) Keeping the same carrier wave, the modulating wave in this example is substituted with a square wave of 50%…
1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is 5V. Calculate the bandwidth , modulation index ,Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHz