We are to design a TDM (PCM) link to facilitate the simultaneous transmission of 10 signals. Each signal has a maximum bandwidth of 4 Khz. The PCM encoding system is designed to maintain a signal-to noise (S.N.R) ratio of no worse than 96 dB. What would be the TDM's (1) overall bit rate and (2) bandwidth (assuming the Nyquist bandwith criteria / 2 times bit rate criteria)?. Single choice.

We are to design a TDM (PCM) link to facilitate the simultaneous transmission of 10 signals. Each signal has a maximum bandwidth of 4 Khz. The PCM encoding system is designed to maintain a signal-to noise (S.N.R) ratio of no worse than 96 dB. What would be the TDM's (1) overall bit rate and (2) bandwidth (assuming the Nyquist bandwith criteria / 2 times bit rate criteria)?. Single choice.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

4. The information in an analog voltage waveform is to be transmitted over a PCM system with a F 0.2% accuracy (full scale). The analog waveform has a bandwidth of 200 Hz, and an amplitude range of -5 to +5 V. determine the following: - The minimum sampling rate needed. - The number of bits needed in each PCM word. - The minimum bit rate in the PCM signal. - The minimum channel bandwidth for transmission of this PCM signal.
An analog signal with a bandwidth of 4.2 MHz is to be converted into binary PCM and transmit- ted over a channel. The peak-signal quantizing noise ratio at the receiver output must be at least 55 dB. (a) If we assume that P=0 and that there is no ISI, what will be the word length and the number of quantizing steps needed? (b) What will be the equivalent bit rate? (c) What will be the channel null bandwidth required if rectangular pulse shapes are used?
Please assist with question 2 with details on how to do it. Thank you. 2. This problem addresses the digitization of a television signal using pulse-code modulation. The signal bandwidth is 4.5 MHz. Specifications of the modulator include the following: Sampling: 15% in excess of the Nyquist rate Quantization: uniform with 1024 levels Encoding: binary Determine (a) the Nyquist rate, and (b) the minimum permissible bit rate.
Six signals, the bandwidth of each one is 2kHz, are to be transmit- ted simultaneously by TDM-PCM. The maximum tolerable error in sample amplitudes is 0.2% of the peak signal amplitude. The signals must be sampled at least 20% over the Nyquist rate. Determine the TDM data rate, and the minimum bandwidth required to transmit this signal.
4. This problem addresses the digitization of a television signal using pulse-code modulation. The signal bandwidth is 4.5 MHz. Specifications of the modulator include the following: Sampling: 15% in excess of the Nyquist rate Quantization: uniform with 1024 levels Encoding: binary Determine (a) the Nyquist rate, and (b) the minimum permissible bit rate.
For a binary unipolar signal, the received signal voltage has a maximum value of 4mV. The rms noise Voltage is 0.5mV, then signal to noise ratio and bit error probability are respectively
(a) Define sampling and quantization. (b) Pulse Code Modulation (PCM) transforms analogue signals into binary digits where it has to be translated into electrical pulses before transmitting in the baseband channel. Each bit in the PCM sequence has bit time slot T = 0.5 ms and the PCM bits as follows: 1010 1100 0110 (i) Convert the binary digits into its basic pulse waveform representation and delay modulation waveform. (ii) Explain the differences of the converted PCM waveforms in Q4(b)(i).
A Delta Modulation system is designed to operate at 3 times the Nyquist rate for a signal with a 3 KHz bandwidth. The quantization step size is 250mV. i) Determine the maximum amplitude of a 1 KHz input sinusoid for which the delta modulator does not show slope overload. Determine the postfiltered output SNR for the signal of part (i). ii)
(3) Five telemetry signals, each of bandwidth 1kHz, are to be transmitted simultaneously by binary PCM. The maximum tolerable error in sample amplitudes is 0.2% of the peak signal amplitude. The signals must be sampled at least 20% over the Nyquist rate. Framing and synchronizing require an additional 0.5% extra bits. Determine the minimum possible data rate that must be transmitted, and the minimum bandwidth required to transmit this signal.
A 450 kHz carrier signal is modulated with a 15 kHz modulating signal. What are its sideband frequencies?
Using Verilog continuous assignment statements or VHDL signal assignment statements, write a description of the circuit shown in
C- Put TRUE or FALSE for only TWO of the following and say why: 1. PCM modulation is very complex technique compared to DM. 2. Envelope detection for PSK signal is possible via using DPSK. 3. A frequency reuse factor can be reached to "1" as a maximum value.