(3) Five telemetry signals, each of bandwidth 1kHz, are to be transmitted simultaneously by binary PCM. The maximum tolerable error in sample amplitudes is 0.2% of the peak signal amplitude. The signals must be sampled at least 20% over the Nyquist rate. Framing and synchronizing require an additional 0.5% extra bits. Determine the minimum possible data rate that must be transmitted, and the minimum bandwidth required to transmit this signal.

(3) Five telemetry signals, each of bandwidth 1kHz, are to be transmitted simultaneously by binary PCM. The maximum tolerable error in sample amplitudes is 0.2% of the peak signal amplitude. The signals must be sampled at least 20% over the Nyquist rate. Framing and synchronizing require an additional 0.5% extra bits. Determine the minimum possible data rate that must be transmitted, and the minimum bandwidth required to transmit this signal.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signal
The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of : 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 43 Hz and an amplitude range of - 10 to 10 Vots. Determine the minimum bit rate fin bps) required in the PCM system? O a 688 O 774 O c 387 O d 86 Oe 258
For a binary unipolar signal, the received signal voltage has a maximum value of 4mV. The rms noise Voltage is 0.5mV, then signal to noise ratio and bit error probability are respectively
Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality
4. The information in an analog voltage waveform is to be transmitted over a PCM system with a F 0.2% accuracy (full scale). The analog waveform has a bandwidth of 200 Hz, and an amplitude range of -5 to +5 V. determine the following: - The minimum sampling rate needed. - The number of bits needed in each PCM word. - The minimum bit rate in the PCM signal. - The minimum channel bandwidth for transmission of this PCM signal.
4. A signal is digitized using pulse-code modulation. The signal bandwidth is 10MHz. Encoding: Binary a) Determine the Nyquist rate. b) If the sampling rate is lower than the Nyquist rate, what effect occurs? What problem does it cause? c) Assuming return-to-zero signaling is used to represent the binary symbols 1 and 0, sketch the waveform for the sequence 1110.
4. This problem addresses the digitization of a television signal using pulse-code modulation. The signal bandwidth is 4.5 MHz. Specifications of the modulator include the following: Sampling: 15% in excess of the Nyquist rate Quantization: uniform with 1024 levels Encoding: binary Determine (a) the Nyquist rate, and (b) the minimum permissible bit rate.
what happens when the modulation order is increased for a modulated signal?
An analog television signal containing frequencies up to 4.5MHz is to be coded by an ADC. The sampling frequency is 20% above the Nyquist rate. If there are 1024 quantizing levels, determine the rate of transmission.
A major advantage of PRTs is that they are very linear. A disadvantage is that they have poor sensitivity. True or false?
The information in an analog waveform, whose maximum frequency fm-4000Hz, is to be transmitted using a 16-level PAM system. The quantization must not exceed #1% of the peak-to peak analog signal. (a) What is the minimum number of bits per sample or bits per PCM word that should be used in this system? (b) What is the minimum required sampling rate, and what is the resulting bit rate? (c) What is the 16-ary PAM symbol Transmission rate?
Answer the following. Use a detailed explanation. In series clippers, when clipping of signal occurs? In parallel clippers, when clipping of signal occurs? What happens to the depletion region if the connection is in reverse bias?