Water (T = 20°C) from a reservoir is pumped up at 5 kg/s through a 3-in Sch. 40 pipe connected to a storage tank of relatively large area. The tank is 7 m from the reservoir where the pump is placed on its side delivering 30 kW of power. The fluid absorbs heat at 3.5 kW. Determine the temperature at the receiver tank.

Water (T = 20°C) from a reservoir is pumped up at 5 kg/s through a 3-in Sch. 40 pipe connected to a storage tank of relatively large area. The tank is 7 m from the reservoir where the pump is placed on its side delivering 30 kW of power. The fluid absorbs heat at 3.5 kW. Determine the temperature at the receiver tank.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 1RQ: Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop...

See similar textbooks

Similar questions

Water with a specific heat of 1 BTU/lbmoF is pumped using a 1-hp jet pump from a well that is 20 ft deep into a vented water vessel 160 ft above the ground. In the process, 400 BTU/min of heat is lost from the system. What is the temperature (oF) of the water as it enters the vessel if the flow rate of the water is 5 gal/min? Assume the temperature of water in the well is (35oF).
A reservoir of 20oC water is pushed at a rate of 5 kg/s to a 3 in Sch. The 40pipe is linked to a relatively big storage tank. The tank is 7 meters away from the reservoir, and the pump, which produces 30 kW of power, is positioned on its side. Heat is absorbed by the fluid at a rate of 3.5 kW. Calculate the temperature of the receiver tank.
Water needs to be delivered from a tank to another one that is 40 ft above the first tank. The water passes througha heat exchanger where 30,000 BTU/min of heat is lost. It will then be pumped to the receiving tank at 45 gal/min.The pump consumes 2 hp to do this. The water arrives at the second tank at 80°F. What was its initial temperature?
A simple saturated refrigeration R-12 system operates at an evaporating temperature of -11 °C and a condensing temperature of 40 °C. Determine the volume flow in m3/sec rate for a refrigerant capacity of 1 kW.
A pump draws saturated water from a condenser which is maintained at 32.15°C. The friction head losses between pump and condenser is measured to be 1.5 m. Determine the minimum height of water level (above pump centerline) in the condenser if NPSH required required for the pump is 3.5m Draw the FIGURE
Water (T = 20°C) from a reservoir is pumped up at 5 kg/s through a 3-in Sch. 40 pipe connected to a storage tank of relatively large area. The tank is 7 m from the reservoir where the pump is placed on its side delivering 30 kW of power. The fluid absorbs heat at 3.5 kW. Determine the temperature at the receiver tank.
Water is to be pumped from the bottom of a well 20 ft deep and 160ft above the ground with a specific heat of 1 BTU/lbm F is pumped using a 1-hp jet pump. Heat is lost from the whole system at the constant rate of 500 BTU/min. What is the temperature (℉) of the water as it enters the vessel if the flow rate of the water is 5 gal/min?assuming that the well water is at 35℉? kindly show all necessary calculations
Water (T = 20°C) from a reservoir is pumped up at 5 kg/s through a 3-in Sch. 40 pipe connected to a storage tank of relatively large area. The tank is 7 m from the reservoir where the pump is placed on its side delivering 30 kW of power. The fluid absorbs heat at 3.5 kW. Illustrate and determine the temperature at the receiver tank.
Water is stored in an elevated reservoir. To generate power, water flows from this reservoir down through a large conduit to a turbine and then through a similar-sized conduit. At a point in the conduit 89.5 m above the turbine, the pressure is 172.4 kPa and at a level 5 m below the turbine, the pressure is 89.6 kPa The water flow rate is 0.800ms The output of the shaft the turbine is 658 kW. The water density is 1000 ke m. If the efficiency of the turbine in converting the mechanical energy gven up by the fluid to the turbine shaft is 89 % (n =0.89). a) Draw a schematic diagram for the process b) Calculate the frictional loss in the turbine in J kg %3D
The air duct of the heating system of a hall, an electric heater placed inside andIt consists of a 300 W fan. While the air is continuously flowing in the duct with a flow rate of 0.6 kg/stemperature rises by 5°C. Since there is a loss of 400 W 151 from the channel surfaces to the environmentCalculate the power of the electric heater. (The specific heating value of air is - 1.005 kJ/kgK.)
Water with a specific heat of 1 BTU/lbm F is pumped using a 1-hp jet pump from a well that is 20 ft deep into a vented water vessel 160 ft above the ground. In the process, 900 BTU/min of heat is lost from the system. What is the temperature (F) of the water as it enters the vessel if the flow rate of the water is 5 gal/min? Assume the temperature of water in the well is (35 F).
The refrigerant circulating in the following system is R404A; the data of the system is as follows: Tev1= -20 oC Tev2= 0 oC, Qev1=10 kW, Qev2=20 kW, Tkon= 40 oC, the efficiency for the compressor is nik=0.80, nmk=0.90, nkk=0.95, nem=0.95. 10 oC over-cooling and 10 oC over-heating will be done in the system. a) draw p-h and T-s diagrams of the cycle.b) 1. and 2. calculate the mass flow through the evaporator and through the compressor.c) determine the temperature (T2) and enthalpy (h2) at the compressor output.d) 1. and 2. determine the degree of dryness when entering the evaporator.e) What would have happened if the expansion valve between stations 5 and 6 had not been used?f) find the power consumed by the compressor.g) determine the cooling performance coefficient COPSM value.H) calculate condenser capacity.I) calculate the heating performance coefficient (COPIP) of the system.