None Using the method of sections, calculate the member forces CD,OI, and PF. Assume P = 500lb. The cable is attached atpoint A and run through pulleys at O, P, and I. Ignore dimensions of the pulleys in your geometric calculations. Partial ans.(for checking): F,= -500lb.=-848.87lb, FDCDFUsing the method of sections, calculate the member forces CD, OI, and PF. Assume P = 500 lb. Thecable is attached at point A and run through pulleys at O, P, and I. Ignore dimensions of the pulleys inyour geometric calculations.PBCDEFG2 @ 9ftJHNMLKP6 @ 9ftPartial ans. (for checking): FDc =-848.87 lb, FDF = -500 lb

Ans Given Now draw the FBD of the given truss asNow using the method of section, cut the truss by a…

Using the method of sections, calculate the member forces CD, OI, and PF. Assume P = 500 lb. The cable is attached at point A and run through pulleys at O, P, and I. Ignore dimensions of the pulleys in your geometric calculations. P D E F G B 2 @ 9ft N M L K J H P 6 @ 9ft Partial ans. (for checking): FDc=-848.87 lb, FDF = -500 lb

Using the method of sections, calculate the member forces CD, OI, and PF. Assume P = 500 lb. The cable is attached at point A and run through pulleys at O, P, and I. Ignore dimensions of the pulleys in your geometric calculations. P D E F G B 2 @ 9ft N M L K J H P 6 @ 9ft Partial ans. (for checking): FDc=-848.87 lb, FDF = -500 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

S00 Ib In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R = 35 (19-20) the angle of the R measured 500 lb cW from the x- axis.
6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in
Use the diagram shown above. Given: • D₁ = 10 ft . • D₂ = 3 ft A #/ft . W = 100 W-100 Solve for the internal moment at X. D₂ D₁ W X Note: Enter your calculation results without the unit. You'll be asked to specify the unit for your calculation result in the following question. (e.g. if it's positive 100, enter 100, if it's negative 100, enter -100.)
RAY B F F₁ ROY
A worker applies forces P = -10i + 8j Ib and Q = 10i Ib to the handle and clamping bar of the power drill. These forces are equivalent to the force R= 8j Ib acting on the drill bit and the couple CR = -120j Ib - in. Determine the dimensions a and b. S in.
The shelf bracket is subjected to the force F = 336 Newtons at an angle 0 = 25.5°. Compute the moment (in N-m) that this force exerts about each of the two attachment points (screw locations in the figure). Take counterclockwise moments to be positive. a F 2013 cc CC Michael Swanbom BY NC SA Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 48.0 cm 45.6 cm 4.10 cm The moment about the upper attachment point is N-m. The moment about the lower attachment point is N-m. luk-
Draw and label the diagram correctlyShow the complete solution. Determine the following:a. Shear and Bending Moment Equationb. Shear and Bending Moment Diagramc. Mmax
2. Given the cantilever framework below, find the shortest distance from point B to line AC and to line AD. 8' A 3. In the system shown below, determine the length of the common perpendicular between lines AE and BD. Solve in two ways. W = 2200 Ib 4. If the magnitude of a force P acting from A to D is P = 20V73 Ib, determine the component of P that is perpendicular to the plane defined by points E, A, and C. 10' B
ENTER YOUR ANSWER THE WAY I SPECIFY HERE IN ADDITION TO DOING IT ON SCRATCH PAPER 400 N 800 N B D A E C 2 m Use the method of sections to calculate the axial force in members AC and BC. Enter your answer in the following way rounded to the nearest whole number. Example If your answer is TAC 2 N tension TBC =3.1 N compression. enter 2Tension;3Compression Enter TAC then TBC (no space)
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 5 m, b = 3 m, PB = 55 kN, Pc = 75 kN, and PE = 25 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a PB Answer: Ay = i BO PB a B Pc a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) D Pc D a D₂ PE a PE E kN, Dy= i -x E X kN.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let o-1.5m.b=3.5 m.w=50 kN/m and P = 45 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. C Calculate the reaction forces A, and D, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, -0, it has been omitted from the free-body diagram.) Answers: A, b KN, D, KN.
4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.