solve the solution with answers given The bolt shown in the following figure is a 5/8 in - 18 UNF grade 5 bolt. The bolt and the clampedplates are of the same length. Assume that the threads stop immediately above the nut. Theclamped steel plates have a stiffness "k." four times the bolt stiffness "k". The load fluctuatescontinuously between 0 and 9,000 lb.(a) Find the minimum required value of initial preload to prevent loss of compression of the plates.(b) Find the minimum force in the plates for the fluctuating load when the preload is 10,000 lb.(c) Based on the initial preload calculated in part “a”, what is the torque requirement for the 5/8 in18 UNF grade 5 bolt when it is initially assembled? (i.e. What torque needs to be applied to thebolt to achieve the initial preload? Assume the nut is held fixed and the bolt is turned into thenut.) Use μμ₁ = 0.15 and d₁ = 1.5d.FeFe 0 To 9,000 lbk₁ = 4kbFeAns. (Part a) Fimin = 7200 lb, Ans. (Part b) Fo_min=2800 lb, Ans. (Part c) T = 78.38 ft lb

Final Answer:-a) Fc = 7200lb (part a)b)Fc = 2800lb(part b)c)78.4 ft.IbExplanation:Step 1: Step 2:…

Answered: The bolt shown in the following figure…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem Chain and Sprocket. A single-strand roller chain drive connects a 10-hp engine to a lawn waste chipper/shredder. As the engine operates at 1200 rpm, the shredding teeth should rotate at 240 rpm. The drive sprocket has 18 teeth. Determine an appropriate pitch for the chain, the number of teeth on the driven sprocket, the pitch diameters of both sprockets, and the chain speed. Also indicate the number of links in a suitable chain and specify the required center distance.
A 3/8-18 grade 8 bolt has 800 pounds of force pulling on it. Find the tensile force, the thread stripping strength for the needed length of engagement and the factor of safety for the bolt with that amount of force.
Figure 8-19 is a cross-section of ASTM A36. A total of N bolts are to be used to resist a separating force of 7258.97N is one bolt. A) Determine kb,km, and C B) Determine the realized load factor for overload, the yielding factor of safety, and the load factor of joint separation.
A bolted joint is to have a grip consisting of two 14-mm steel plates and one 14R metric plain washer to fit under the head of the M14 x 2 hex-head bolt, 50 mm long. (Hint: Look up table A-31 and A-33 in the textbook of Shigley's Mechanical Engineering Design, 8th Edition) (a) What is the length of the thread LT for this diameter metric coarse-pitch series bolt? (b) What is the length of the grip l? (c) What is the height H of the nut? (d) Is the bolt long enough? If not, round to the next larger preferred length. (e) What is the length of the shank and the threaded portions of the bolt within the grip?
34 in 3. The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))
Use the drawing below to answer the following two questions. a. Determine the equivalent spring stiffness of the following system. Simplify the expression (ie – single common denominator. Your answer should be an expression of just K’s – no numbers). b. If the weight on top is 20 lb and the K1 = K4 = 50 lb/in, K2 = 33 lb/in and K3 = K5 = 25 lb/in, what is the natural frequency of the system?
Two identical aluminum plates are each 3 in thick, and are compressed with one bolt and nut. Washers are used under the head of the bolt and under the nut. Washer properties: steel; ID = 0.531 in; OD = 1.062 in; thickness = 0.095 in Nut properties: steel; height = 7/16 in Bolt properties: 1/2 in-13 UNC grade 8 Plate properties: aluminum; E = 10.3 Mpsi; Su = 47 kpsi; Sy = 25 kpsi (a) Determine a suitable length for the bolt, rounded up to the nearest 1/4 in. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members.
Required information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.
Statement: The figure below shows three cycles of time-varying loading on a double D-ring held together with a single bolt and nut. The figure shows both the bolt tensile force and the member compressive force. QUESTION 1 - Based on the figure, give the minimum and the maximum of the external load, P?
A screw jack mechanism is shown in the figure below (not drawn to scale). A belt drives a sheave that rotates the nut. The screw is a single-thread,1 1/2-4 ACME screw. Notice that a pin is used in a groove to prevent the screw from rotating. The sheave has a pitch diameter of 14 inches. The belt is driven by an electric motor (not shown) with a sheave pitch diameter of 2.8 inches at 1650 rpm. Determine the lifting speed of the jack. Determine the belt speed. Find the lifting speed (s) of the jack (in/min): Find the belt speed vb (ft/min):
The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using 73 bolts. A confined gasket seal has an effective sealing diameter D of 0.9 m. The cylinder pressure is cycled between a minimum pressure of zero and a maximum pressure pg of 535 kPa. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes. Use Table A-17 for calculation purposes. Parameter Value Head thickness, A Cylinder thickness, B Internal diameter of the cylinder, C Gasket sealing diameter, D Bolt circle diameter, E Outer diameter of the cylinder head, 16 mm 25 mm 0.8 m 0.9 m 1.0 m 1.1 m F Bolt grade ISO 10.9 Bolt diameter, d 10 mm NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Find a suitable bolt length. Then, determine the bolt stiffness, material stiffness, and stiffness constant of the joint. The bolt length is 50 mm.…
Clear selection Determine the number of pin joints 7. Which of the following has multiple degrees of freedom?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS