4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m.a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel,Mpapendicularb. Find the point of intersection of the axis of the wrench with the x-y plane. How do youcheck your answer is correct?G FDAB.

Answered: Image /qna-images/answer/3a391238-7fbc-4e13-93ca-1cbe8b1413eb.jpg

4. Forces F1 =F= 20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mperpendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do check your answer is correct? you F2 G F D C. F3

4. Forces F1 =F= 20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mperpendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do check your answer is correct? you F2 G F D C. F3

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

2-25 A cantilever beam supports forces as shown in Figure P2-25. Determine the resultant. 50 100 45 Figure P2-25
The rectangular framework is subjected to the following non-concurrent system of forces: a 30lb- force below the origin, a 20 lb-force,3ft above the origin and making an angle of30°N of E, a 100lb-force with a horizontal distance of 3ft and a vertical distance of 4ftfrom the origin and making an angle of 45°NW , a 60lb -force with the same distance like the previous force but along the positive x-axis, and a 100lb- force 4ft tothe right of the origin and making an angle of 60° S of W . Determine the magnitude and direction of the resultant, as well as its moment arm relative to the origin.
НОМE WORK 3 Determine the resultant force at A. for the figure below Hint : 1- Find the position of all points A,B.C (x, y., z) 2. Find Fas und FAC 3. Find Tanl and Iracl 4. Find FAg = F UA and Fac = F UAC 5- Finally find R and a, B.y 3m Fc= 500N FB= 500N 3m 5m 3m B 2m 4m 5m
The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on the image. The beam has a length of 7,50 m and a mass of 4,25 kg. Object 1 has a mass of 1,50 kg; object 2 has a mass of 2,35 kg. Point P is 0,50 m form the center of the beam. CG 1. How much is the torque done by object 1 around point P? A. 55,2 N*m B. 7,36 N*m C. 62,5 N*m D. Object 1 doesn't exert a torque. 2. How much is the torque done by the force of gravity of the beam around point P? A. 20,8 N*m N-m ך177 .B C. 156 N*m D. 313 N*m 3. If you needed to cancel the nomal forces of the two objects, where you should place object 2? The axis of rotation is point P. A. 3,30 m from point B. 9,18 m from point P C. 5,69 m from point P D. 3,62 m from point P
PS2-5 Three forces are acting on the problem. List all of the simplifications that can be used in the problem. What is the simplest problem? F₂ 45° R
perpendicular to the page through the point o. (Let counterclockwise torque be positive and let forces to the right and up be positive. Use the following as necessary: the forces R, Write the necessary equations of equilibrium of the object shown in the figure below. Take the origin of the torque equation about an axis RFF, and F the length l of the object; and the angle e that the object makes with the horizontal.) EF, = = 0 Fy =0 Στ. =0 Need Help? Read It
2-28 Find the resultant of the force system shown in Figure P2-28. 50 N 40 N 52 N 12 15 8 34 N Figure P2-28 3
S00 Ib In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R = 35 (19-20) the angle of the R measured 500 lb cW from the x- axis.
F1-100 2m F2-250 A 4m F3-200 2,5m Find the forces acting on supports A and B in the figure. F4-150 3m B
Determine completely the resultant of the forces acting on the step pulley in Figure 1-36. 750 lb 2 = 1- 60 - 250 lb 1250 lb Figure 1-36
The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same magnitude of 20 N and are directed parallel to the long and short sides of the rectangle. The long side of the rectangle is twice as long as the short side. An axis of rotation is shown perpendicular to the plane of the rectangle at its center. A third force (not shown in the drawing) is applied to corner A, directed along the short side of the rectangle (either toward B or away from B), such that the piece of wood is at equilibrium. Find the magnitude and direction of the force applied to corner A.
6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in