The working current has a power of 100 kW and the reactive current has a power of 125 kW. If a capacitor is used to improve the power factor to 0.95, what is the capacitor capacity needed? (In KVAR) Answer: 92

The working current has a power of 100 kW and the reactive current has a power of 125 kW. If a capacitor is used to improve the power factor to 0.95, what is the capacitor capacity needed? (In KVAR) Answer: 92

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 14RQ: What is the minimum KVAR rating of each capacitor in Question 11? (Round off the value to the...

See similar textbooks

Related questions

Q: Discuss the importance of power system stability and control. What methods are employed to maintain…

A: Power system stability is of paramount importance in the field of electrical engineering and the…

Q: 12.73 For the circuit displayed in Fig. 12.74, find the wattmeter readings. 240/-60° V 240/-120° V…

A: Given circuit:Asked to find the wattmeter readings?

Q: Explain the concept of load flow analysis in power systems. How is it useful in maintaining grid…

A: Load flow analysis, also known as power flow analysis, is a critical technique in power systems…

Q: What is the smart grid, and how does it impact the efficiency and reliability of power systems?

A: The smart grid is an advanced and digitally enabled electrical grid that integrates various…

Q: There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that…

A: Given:A system that works with a sampling rate of 48 kpsp and requires a bandpass filter that allows…

Q: Find the phasor representation of the given sinusoid and its angular velocity. (Express magnitude…

A: given here sinusoid and asked to find it's phasor represenationwe know that, if a sinusoid is given…

Q: Suppose you have a voltage source that produces 10 V and has internal resistance of 1 killo-Ohm. You…

Q: Consider the unity negative feedback control system below, Y(s) R(s) + G(s): = where G(s) and C(s)…

Q: (a) Determine the peak value of the output voltage for Figure 2-28 if the turns ratio is 0.5. (b)…

A: For the given half-wave rectifier circuit the value of peak secondary voltage, output waveform and…

Q: An op amp, with the parameters indicated below, is used in a feedback configu-ration as shown. If…

A: Given:an op-amp circuit, A = 562 kV/VVofs = 22.5 mVVR = +15 V, -15 VTo find:Vout, if the input…

Q: What is the purpose of a substation in a power distribution system?

A: A substation is a crucial component of a power distribution system, serving several essential…

Q: Explain the role of transformers in power distribution and transmission, including step-up and…

A: Transformers are essential components in both power distribution and transmission systems, and their…

Q: Given that determine the Fourier transform of f(t)etjwot+ ⇒ F(w = wo), f(t) sin(wot).

Q: onsider the B My logic circuit shown below. Which of the logic expression is correct +VDD M₂ M₁…

A: 1. For given CMOS circuit identify thelogic gate.When A=B=0: M1=M2=ON and M3=M4=OFF. Hence,

Q: Each leg of a symmetric, Y‐connected, 3Φ load has an impedance of 10∠36.87° Ω, and is connected to…

A: Given Data:A three-phase, balanced, star-connected supply with,Phase voltage Per phase…

Q: What is a power system in electrical engineering, and what components make up a typical power…

A: It is asked to explain a power system in electrical engineering and its components.

Q: 1) Design a sequential circuit whose state table is shown below. Use JK flip-flops for the design.

A: For the given state table the sequential circuit needs to be designed and the circuit should be…

Q: Explore the challenges and solutions related to power quality in electrical systems. How do issues…

A: To explain:i) Challanges and solutions of power quality in electrical systems. ii) What are the…

Q: Describe the principles and benefits of High Voltage Direct Current (HVDC) transmission systems, and…

A: HVDC transmission is based on the principles of converting alternating current (AC) to direct…

Q: 3. Find the total admittance for the following parallel impedances: Z₁ = 0.5290° Z2 = 0.1Ω < – 90° /…

Q: How do power factor correction devices work, and what benefits do they provide in commercial and…

A: Power factor correction is a technique used in industrial power systems to improve the power factor…

Q: What is load shedding, and how does it help in maintaining the stability of a power system during…

A: Load shedding is a controlled and intentional reduction of electricity supply to specific areas or…

Q: How would you improve the dimensions of the transmission lines and interconnects?

A: The given figure is shown below.This is the internal diagram of transmission lines and interconnects…

Q: Describe the primary components of a typical power system.

A: A typical power system, which includes the generation, transmission, and distribution of electrical…

Q: Find vo. I 2.4 Α Μ τη 24 Ω (1.2A, 12 Μ 18 Ω 16 Ω 12 Ω ig 15 V

A: given a circuit and asked to find the voltage V0.

Q: Discuss the role of HVDC (high-voltage direct current) transmission systems in long-distance power…

A: High-Voltage Direct Current (HVDC) transmission systems operate by converting alternating current…

Q: Explain the concept of a power grid and its importance in the distribution of electrical energy.

A: A power grid, often simply referred to as "the grid", is a vast interconnected network for…

Q: Discuss the concept of a "smart grid" and its potential benefits in modernizing power systems.

A: A smart grid is an advanced, digitally enabled electrical grid that uses modern communication and…

Q: Consider common-source amplifier circuit shown below with K = 50μA/V2, Vto = 2V, L = 10µm and W =…

A: We need to find out the input impedance for given circuit.

Q: S1 (a) R2 V₁ = 10V. C1 I₁(t) L2 Given the circuit in figure 7 with values R-3000-1300, R-5000-7000 -…

A: Given circuit:Asked to find the,redraw the circuit with and label all voltages and currentcapacitor…

Q: Using Thevenin’s theorem, find Vo in the circuit shown given that Vs = 6V , R1 = 6kΩ, R2 = 7kΩ, and…

A: The given circuit diagram is shown below,

Q: Name: 4. Use Laplace transform to find the current in the following RLC circuit. Current and charges…

Q: Use the superposition principle to find i, and v. in the circuit of Fig. 4.79.

A: The value of the unknown voltage and current needs to be calculated by using the superposition…

Q: Coexistence of radar systems. In this problem, we’re trying to determine whether two radars are…

A: According to the question,Radar 1Frequency = 3 GHzPeak power = 100 kWCircular array – diameter = 2…

Q: A rectangular loop carrying 104 of current is placed on z = 0 plane as shown in Figure 7.32.…

A: As per the company guidelines, the answer to the first three sub parts can be given Please post the…

Q: What are the methods for voltage regulation in a power distribution system, and how are they…

A: Voltage regulation in a power distribution system is crucial for maintaining the quality of…

Q: ³8 8 (843) Solve the following differential equation by Laplace transform: 2 day dy dt +4y(t)-e-2…

Q: Elaborate on the evolution of fiber optic cables and their advantages over traditional copper cables…

A: The evolution of fiber optic cables and their advantages over traditional copper cables in terms of…

Q: What is the significance of fault analysis in power systems, and how is fault location determined?

A: Fault analysis is an essential tool for the determination of short-circuit currents that result from…

Q: Problem 2 5.2 Figure 5.4 shows a latch built with NOR gates. Draw a similar latch using NAND gates…

A: To do:we need to a SR latch using NAND gates. Also we need to derive its characteristic table and…

Q: There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that…

A: There is a system that works with a sampling rate of 48 kbps and requires a bandpass filter that…

Q: Example 4: Consider a shunt DC motor with the following values for nominal terminal voltage,…

Q: Calculate the magnitude of the load's line voltage. (

A: In this question, we need to determine the magnitude of the load's line voltage in rms.

Q: Describe the concept of "smart grids" and how they enhance the efficiency and reliability of power…

A: Smart grids are advanced electrical power systems that incorporate digital communication,…

Q: Describe the role of protective relays in power systems and provide examples of their applications.

A: According to the question, we need to describe the role of protective relays in power systems and…

Q: 53. Find RT in Figure 5-87. FIGURE 5-87 R₂ 12 V www <-5.6 Mn R₁ 4.8 V Ry P = 21.5 μW +6

A: Given circuit:Asked to find the total resistance RT =?

Q: What are the basic components of an electrical power system?

A: Electrical power systems are complex networks designed to generate, transmit, distribute, and…

Q: What is the significance of load flow analysis in power systems, and how is it performed?

A: Load flow analysis, also known as power flow analysis, is a crucial and fundamental tool in power…

Q: Explain the importance of reactive power in electrical power systems and how it affects system…

A: Reactive power, denoted as Q and measured in volt-amperes reactive (VAR), is the power that flows…

Q: What are the different types of power losses that occur in a power system, and how can they be…

A: In a power system, there are several types of power losses that occur, each with its own causes and…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

Solve correctly

The working current has a power of 100 kW and the reactive current has a power of
125 kW. If a capacitor is used to improve the power factor to 0.95, what is the
capacitor capacity needed? (In KVAR)
Answer: 92

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Requirement

VIEW

Step 2: Calculation of reactive power compensation requirement

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
What is the minimum KVAR rating of each capacitor in Question 11? (Round off the value to the nearest KVAR.)
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
Calculate the value of the resistor(R) that must be connected in parallel with a nine μF capacitor(C) to produce a power factor equivalent to 0.75 when connected to a sixty Hz AC source.
Calculate the RMS voltage. GIven that resistor has a 1000 ohms and a capacitor has a value of 5microfarad.
A 100 ohm resistor is connected with a 530 mH inductor and 530 uF capacitor. If the circuit is connected to a 530 V, 60 Hz source, finda. Pb. Q
The value of Inductance can be determined by a. XL/2π b. 2πf / XL c. XL 2πf d. XL / 2πf
THREE CAPACITORS HAVING THE SAME CAPACITANCE (C = 200microFARAD) ARE CONNECTED IN SERIES WITH A 9 VOLTS BATTERY. FIND THE TOTAL CAPITANCE. a.) 66.67microFARAD b.) NONE OF THE CHOICES c.) 76.67microFARAD d.) 15000 FARAD NOTE : DON'T ANSWER NO. 5 6. WHAT IS THE TOTAL CHARGE? (IN ITEM NUMBER 5) a.) 0.0006 C b) 0.00006 C c.) 6 C d.) NONE OF THE CHOICES
A resistor of 20Ω, an inductor of 0.012H, and a capacitor of 90 μF are connected in series with a 100-V generator, with a frequency, 130 Hz. Calculate the phasor relationship between the current and the voltage in the circuit.
An inductive circuit has a resistance of 10 ohms and an inductance of 2 henrys. The total impedance at 60 HZ is?
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
When a load is connected to a power line with a frequency of 230V (rms) 50 Hz, it draws 4500 W at a power factor of 0.80. Find the required capacitance value to increase the power factor to 0.85.