The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fitings are flanged The vohume flow rate is 300 L'min 45 treaded elbow

The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fitings are flanged The vohume flow rate is 300 L'min 45 treaded elbow

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below:Loss coefficients:• check valve, k = 5.0• gate valves, k = 0.20• elbows, k = 0.75• flowmeter, k = 13.0Pump flowrate = 10 m3/hrFluid power adding by pump = 3.7 HPPressure at point 1 = 60 kPagPipe inside diameter = 50mmViscosity = 0.17 Pa.sSpecific gravity = 0.89Pipe inside surface roughness = 0.00015 ft.
A pump delivers water from a tank (A)X water surface elevation-110m) to tank B (water surface elevation= 170m). The suction pipe is 45m long and 35cm in diameter the delivered pipe is 950m long 25cm in diameter. Loss head due to friction hf1 = 5m and h2 3m If the piping are from pipe(1)= steel sheet metal pipe(2)= stainless – steel Calculate the following i) ii) The discharge in the pipeline The power delivered by the pump.
Series pipe ABCD consists of 10,000 ft of 20′′, 8000 ft of 16′′, and L ft of 12′′ (C = 120). What length L will make theABCD pipes equivalent to a 15′′ pipe, 16,500 ft long, C = 100? If the length of the 12′′ pipe from C to D were 3000 ft, whatflow (in mgd) would occur for a lost head of 135 ft from A to D? please include fbd
-Example the values. asystem total head. against for the initial condition, show below - give the Lallowiny data dynamic uiscosity of liquid Calculate capacity curve density S-1200 kgim3 Static head on Suction Side 7S-3m Static heac on discharge Side Zd= 7m inside diameter of pipe di = o.052m -pipe roughress E3D0.00045m. gas pressure aboue the liquid in the tank Side of the pump the Suction Ps= atmospheric pressure. gas pressure above the liquicd in the tank on discharge side of the pump. the dund Pd= atmesperic pressure
i just need final answer The water is delivered with piping system given in the figure below. The elevation difference between enteringsection and tank is 121,63 m. Estimate the gage pressure (MPa) at point 1. (Note: For water at 20°C, takep=998 kg/m and p=0.001 kg/ms.)
In the pipeline in the figure, water is transmitted from a-tank to Bdepo with a flow rate of 40OL/s from plastic pipes. Pipe lengths are L1 = 20m, Lz=30m and bore diameters, D:=0.2 m, D2=0.4 m. Find the AH level difference between the two tank water surfaces. Take the kinematic viscosity of water v=4,25.10s m2/s. Loss of entry to the pipe Kbg=0,5 L1 =20 m D1=0,2m A ΔΗ Valve loss coefficient Kvalve = 10 valve Warehouse entry loss coefficient Kdg = 1 %3D Kao = [1- T Sudden expansion loss coefficient KAG L2=30m D2=0,4m
A paint shop in the water flow through the pipe in the radius r Q = 0.05 m /s, density p= 1000 kg/m 3 type. The pipe friction coefficient is Cf= 0.0075 and the local loss coefficient K = 10. Pressure drop in the pipe; AP = p 2C K %3D where the water velocity in the pipe can be calculated with V = Q/(r²). What should be the radius of the pipe so that the pressure drop that will occur in a pipe of L = 100 m length does not exceed AP = 200 000 N/ m 2? State the tolerance value provided by the result you found.
1:The water pump in Figure below maintains a pressure of 45 kPa at point 1. There is a filter (kr), a half-open disk valve (kvalve 0.28), and two regular screwed elbows (kellbow -0.64), submerged exit (kexit 1). There are 24 m of 0.10 m diameter commercial steel pipe. If the flow rate is 0.011 m/s, what is the loss coefficient of the filter (kr)? Take that the density and dynamic viscosity of water are p-998 kg/m³ and -1.0 x10³ kg/m.s. The roughness ratio of pipe is e/D=0.0006. (2) Pump Valve A Filter Elbows 2.75 m V
A two branch duct system of circular duct is shown below. The fittings have the following equivalent lengthof straight duct upstream to branch 4m elbow 2m. There is negligible pressure loss in the straight throughsection of the branch. The designer slects 4pa/m as the pressure gradient in the 12- and -15m straight sections. What diameter in should be selected in the 15 m branch section? A. 0.35 B. 0.66 C. 0.56 D. 0.46
4) The water pump in the Figure maintains a pressure of 6.5 psig at point 1. There is a filter, a half-open disk valve, and two regular screwed elbows. There are 80 ft of 4-inch diameter commercial steel pipe. (a) If the flow rate is 0.4 ft³/s, what is the loss coefficient of the filter? (b) If the disk valve is wide open and Kfilter = 7, what is the resulting flow rate? Pump Valve Filter Elbows 9 ft
Problem : Taking into account only the local resistances, detemine the level difference in the tank H. Given: flow rate Q=25 l/sec, dz=120 mm, di=90 mm, Svedg=4. Build up the piezometric line.
A two branch duct system of circular duct is shown below. The fittings have the following equivalent lengthof straight duct upstream to branch 4m elbow 2m. There is negligible pressure loss in the straight throughsection of the branch. The designer slects 4pa/m as the pressure gradient in all sections. What diameter in m should be selected in the 7-m branch? A. 0.44 B. 0.64 C. 0.34 D. 0.54