The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt= i prad

The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt= i prad

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods AB & DE and a pin support at C. Bar ACD was horizontal prior to the application of load P. The tensile strain measured in rod AB after the application of the load is ɛ1= 0.003. Determine the rotation 0 of the bar ACD and the normal strain in rod DE. Also calculate the value of load P for these deformations. The diameters of rod AB and DE are 1.5 in. and 2 in, respectively. P - 4 ft 4 ft- 6 ft A Rigid (2) 6 ft 8 ft (1) E В
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm
Question 4 At a point in a thin steel plate in plane stress (0z = Txz = Tyz = 0), Ex=800µ, &y= - 400u, and xy = 200u. For the steel plate, G = 76.92 GPa and V= 0.30. %3D (a) Determine the extensional strain &z at this point. (b) Determine the stresses Ox, Oy and Txy at this point. (c) Determine the change in volume or dilatation, Ɛv, at this point.
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A bar of a uniform cross-section is rigidly fixed at one end and loaded by an off-centre tensile point load F = 1.5 kN at the other end, see Fig. Q1a. The Figure Q1b presents the view of the beam from the free end where the point of application of the load F is indicated as A. The allowable stress [0]=234 MPa The geometrical parameters are given as follow h 18 mm, b=37 mm N y b Figure Q1a Figure Q1b h F X
The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part (b) of the figure below). (Consider only the in-plane stresses - the stresses in the xy-plane). 117,600 psi B A 6,650 psi A Cross Side |2,700 psi Section View (a) (b) Determine the maximum shear stresses (in psi), associated normal stresses (in psi), and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For maximum shear stress, enter the magnitude. For normal stresses, use the sign convention for stresses acting on inclined sections.) max = psi psi 02 psi %3D ° counterclockwise from the +x-axis p1 p2 ° counterclockwise from the +x-axis
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
The wire BC has a diameter of 0.175 in. and the material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle at D if the pull at the grip is slowly increased and reaches a magnitude of (a) P= 480lb, (b) P= 700lb. Assume the bar is rigid.
Determine the normal strain EAB in wire AB.
Problem (1) Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm? cross-sectional area and rod EF has a 600 mm? 500 mm cross-sectional area. В (a) statically determinate or indeterminate. Why? (b) stress in each rod. State whether the structure is E 400 mm Determine the force and the OF Determine the deformation of each rod. (c) Note: The link BED is rigid, and BE = ED.
Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and 60 MPa (Tensile). If the shear stress across these planes is 30 MPa, find the principal stresses.