4. The figure below shows a copper rod that is placed in an aluminum tube. The rod is 0.0058 in. longer than the tube. Find the maximum safe load P that can be applied to the bearing plate, using the following data: Bearing plate 0.0058 in. 11 in. Copper Aluminum Сорper Aluminum Area (in.2) E (psi) 3 17 x 106 10 x 10 Allowable stress (ksi) 20 10

4. The figure below shows a copper rod that is placed in an aluminum tube. The rod is 0.0058 in. longer than the tube. Find the maximum safe load P that can be applied to the bearing plate, using the following data: Bearing plate 0.0058 in. 11 in. Copper Aluminum Сорper Aluminum Area (in.2) E (psi) 3 17 x 106 10 x 10 Allowable stress (ksi) 20 10

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which is 699.93mm long. If the weight of the beam is 375KN, determine the stress in the aluminum bar in MPa. (Round your answer to 3 decimal places) (Exclude your unit in the answer box) Bronze Alum 850 1500 Ain mm E in GPa 70 83 bronz alum bronze
The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber= 20MPa Allowable shear strength of the steel = 200MPa Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt?
sinav.gelisim.edu.tr/ExamUser/Take?examSessionld The yield imit for a typE of steel material is determined to k3600 keran. Detemine the permissible (allowable> tensile sress for this material acxording to S64S. (o r=) D 2,16 ton/cm² 23.60 ton /cm² 2 2,04 ton /cm² 1,44 ton /cm2 DBoş bırak Карat
d Given: 9/8 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731 inch Inside diameter of washer = 9/8 inch Tensile stress in the nut = 18 ksi Bearing stress = 800 psi 2 in Required: 5/8 in Shearing stress in the head of the bolt Shearing stress in threads of the bolt Outside diameter of the washer 1 2. 3. 0.731 7/8
7. ASTM suggests a tolerance of... percent to allow the variation in strength as a test of ....w. water. A. 12 В. 8 C. 10 D. 15 E. 16 F. None of them
The two wooden boards shown in the figure are connected by a 0.5 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D  2 in. and d 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress MPa between the washer and the wood
24 Tensile test well done with standard tensile test spaceman with diameter 25 mm & length 120 mm the table in the attachment picture shows the applied load in KN and the elongation in mm. the yield stress is Load 37.5 75 75 85 110 120 125 115 (KN) Elongation (mm) 100 0.06 0.12 1.4 4 12 18 24 29 32 O 320mm2 O 325mm2 O 239mm2 O None of the above
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter of the rivets is 7/8 in, and angles are each 4×31/2×3/8 in. For each rivets assume that the allowable stresses are T= 15 ksi and stress in b is 32 ksi. What is the bearing strength of the grinder? What is the bearing strengtht of the beam? What is the shear strength of the rivets? What is the maximum load that the connection can carry?
(1) Given A992 steel Ag = 10 in %3D KLy- 80, ry what is $ Pa=? = 60 the' column streugth design
help me please
Bar A was manufactured 2 mm less than bar B due to an error. The attachment of these bars to the rigid bar wouldcause a misfit of 2 mm. Calculate the initial stress in each assembly. Which of the two assembly configurationyou would recommend? Use modulus of elasticity of E = 80 GPa and diameter of the circular bars as 32 mm.