The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD is made of a brass with an allowable shearing stress of 5.8 ksi. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 8 in. 4 in. D B -3 in. t = in. Determine the corresponding required value of the diameter ds of spindle AB. The corresponding required value of the diameter is | in.

The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD is made of a brass with an allowable shearing stress of 5.8 ksi. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 8 in. 4 in. D B -3 in. t = in. Determine the corresponding required value of the diameter ds of spindle AB. The corresponding required value of the diameter is | in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 56 MPa in the shafts and 22 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 261 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 194 mm in diameter. If the torque that can be applied is 8728 Nm without exceeding a shearing stress of 52.59 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places. Add vour answer
Illustrate and completely solve the problem! Write legibly or type written the solutions. The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4 x 103 ksi and G brass at 5.2 x 103 ksi.
Write legibly, provide manual step by step solution, and diagram for below given problem. A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34in. bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 7.3ksi? Ans. 39,034.94 ft-lb
Design the size of solid steel shaft to be used for a 500 hp, 250rpm application if the allowable torsional deflection is 1o andthe allowable stress is 10,000 psi and modulus of rigidity is 13x 106 psi. Round your answer to the nearest 1/8 inch.
Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A 40-mm diameter, 522-mm length shaft is drilled, for a part of its length L1, to a 20 mm diameter and for the remaining length L2 to a 30 mm diameter drill hole. If the allowable shear stress is 86 MPa, find the maximum power that the shaft can transmit at a speed of 226 rev/min. If the angle of twist in the length of 20 mm diameter drill hole is equal to that in the 30 mm diameter drill hole, find the length of the shaft that has been drilled to 20 mm and 30 mm diameter.
A solid steel bar with a circular cross-section has diameter 50 mm, length 1.5 m and shear modulus of 80 GPa. If the allowable shear stress is 48 MPa and the allowable angle of twist is 2.0 degrees, then what is the maximum permissible torque? State your answer in Nm to 1 decimal place.
Answer the following problem. Show your complete solution. Use 4 decimal places. 2. Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a way that the shear stress in shaft does not exceed 100 N/mm2. If six bolts are used to join the flange and the bolt circle is 150 mm in diameter. Determine the diameter of the bolt if the permitted shear stress in the bolt is 80 N/mm2.
3. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Determine the maximum shearing stress and the angle of twist. Use G = 12 x 10° psi. a. Identify the stress that is induced in the problem. b. Set up the equations of stress and twisting angle that is required to solve the problem. c. Solve for the unknown variables by substituting the given in the equations that has been set up previously.
Please help me solve this. I need answer asap. Tysm!! A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 275 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 193 mm in diameter. If the torque that can be applied is 9821 Nm without exceeding a shearing stress of 54.36 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
The uniform 3-Mg bar is supported by a smooth wall at A and pin connected a B (double shear). Determine the diameter of the smallest pin that can be used without exceeding the allowable shearing stress in the rivet is 70 MPa. Express your answer in "mm" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUTA UNIT IN YOUR ANSWER, only the numerical value is required* 10m
Q2: A rectangular key is used to connect a gear on a shaft of d=50 mm. The shaft transmitting power at a maximum shear stress. The shaft is made of AISI 1040 CD steel and the key is made of AISI 1020 CD steel. Design the dimensions of the key. Take F.S =3.