1.5 (A). A simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress is limited to 180 MN/m²? [39.2, 61.1 MN/m², 88.4 kN.]

1.5 (A). A simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress is limited to 180 MN/m²? [39.2, 61.1 MN/m², 88.4 kN.]

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.5P: An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with...

See similar textbooks

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle carries an axial load of 30 kN? Assuming a sufficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress 1s limited to 180 MN/m*?
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across section B, the compressive stress between the pin and the rod, and the compressive stress between the pin and the yoke. Given n = 1 (3 / 4) in., a = (15 / 32) in., e = (27 / 32) in., b = (15 / 16) in., d = (19 / 32) in., f = 1".
Two 35 mm shafts are connected by a flanged coupling. The flanges are fitted with 6 bolts on 125 mm bolt circle. The shafts transmit a torque of 800 N-m at 350 rpm. For the safe stresses mentioned below, Safe shear stress for shaft material = 63 MPa Safe stress for bolt material = 56 MPa Safe stress for cast iron coupling = 10 MPa %3D Safe stress for key material = 46 MPa Calculate: (i) diameter of bolts ; (ii)thickness of flanges ; (iii)key dimensions ; (iv)hub length; and (V)power transmitted.
2. A 30-mm bolt with an initial tension of 35 kN is subjected to several types of stresses during initial tightening or due to screwing up forces. If the bolt has a core diameter of 25.7 mm and considering 5 threads are already engaged with the nut, calculate the shear stress across the thread and the crushing stress between the threads. Assume 3.5 mm as the width of the thread section at the root.
4. The allowable tensile stress for a ½ bolt of thread length 7/32 inches is 30000 psi. The allowable shear stress of the material is 15000 psi. Where and how such a bolt most likely to fail, will it fail in the root diameter or the in the thread.
A compound tube consists of a steel tube 120 mm internal diameter and 140 mm external diameter and an outer brass tube 140 mm internal diameter and 10 mm thickness. The two tubes are of the same length equal to 150 mm. The compound tube carries an axial load of 800 kN. Estimate the stresses and the load carried by each tube and the amount it shortens. Take E for steel as 2 × 105 N/mm2 and for brass as 1 × 105 N/mm2.
The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb. Rapid cycling for many million cycles is expected. As the tensile load fluctuates between 4,000 lb and 1,200 lb, it creates fluctuating normal stresses. Calculate the following stresses at the section through the hole. Note: SAE 1050 OQT 1300 steel, wrought steel (a) Maximum tensile stress (psi) (b) Minimum tensile stress (psi) (c) Median stress (psi)
In the clevis shown in Figure 4.3, find the maximum bolt diameter and the minimum thickness of each yoke that will support a load of P=14 kips without exceeding a shearing stress of 12.15 ksi and a bearing stress of 20.15 ksi. Figure 4.3
A 20 mm diameter bett having a diameter at the toot ef the thread of 18.6 mm is used to fasten two timbers as shown in the figure The nut is tightened to cause a tensile lnd Ind on the bolt of 34 kN, Determine: a) Chearing Stress in the head of the bott b) the shearing stress in the threads C) The putside diameter of the warher if the inside dioneter is 28mm and the bearing stress is limited to G MPa. 12 mm 16 mm
A 7/8-in diameter bolt, having a diameter at the root of the threads of 0.731 in., is used to fasten two timbers together. The nut is tightened to cause a tensile stress of 18 ksi in the bolt. Compute the shearing stress (ksi) in the head of the bolt and in the threads. Also, determine the outside diameter of the washers (inches) if their inside diameter is 9/8 in. and the bearing stress is limited to 800 psi. 1/2 in 5/8 in