5. Consider a Pitot probe in high-speed flow.(a) Give the value of the stagnation pressure to the freestream pressure p0/p∞ for airand M∞ = 1. Assume stagnation is reached isentropically.(b) How is the value found in part (a) important for Pitot problems? As part ofyour discussion, include what the flow field looks like for different cases and thedifferent assumptions that have to be made.

5. Consider a Pitot probe in high-speed flow.(a) Give the value of the stagnation pressure to the freestream pressure p0/p∞ for airand M∞ = 1. Assume stagnation is reached isentropically.(b) How is the value found in part (a) important for Pitot problems? As part ofyour discussion, include what the flow field looks like for different cases and thedifferent assumptions that have to be made.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A typical carbon dioxide tank for a paintball gun holdsabout 12 oz of liquid CO2. The tank is fi lled no more thanone-third with liquid, which, at room temperature, maintainsthe gaseous phase at about 850 psia. (a) If a valve isopened that simulates a converging nozzle with an exitdiameter of 0.050 in, what mass fl ow and exit velocityresults? (b) Repeat the calculations for helium.
An incompressible fluid of density ? and viscosity ? flows through a curved duct that turns the flow 180°. The duct cross-sectional area remains constant. The average velocity, momentum flux correction factor, and gage pressure are known at the inlet (1) and outlet. (a) Write an expression for the horizontal force Fx of the fluid on the walls of the duct in terms of the given variables. (b) Verify your expression by plugging in the following values: ? = 998.2 kg/m3, ? = 1.003 × 10−3 kg/m·s, A1 = A2 = 0.025 m2, ?1 = 1.01, ?2 = 1.03, V 1= 10 m/s, P1,gage = 78.47 kPa, and P2,gage = 65.23 kPa
Z\0 @ P 0:10 ZAIN IQ II. Quiz 2 Thermo.pdf Gas flowing through a diverging nozzle has at inlet section a temperature of 20 °C, pressure 120 kN/m² and velocity 300 m/s. At the outlet of the nozzle the velocity has fallen to 100 m/s. Assuming an adiabatic flow, what is the values of outlet pressure, temperature, internal energy and specific enthalpy at outlet section. Take y= 1.333 and Cv= 0.86 kJ/kg K.
Air flows from a tank through a nozzle into the standardatmosphere, as in Fig. A normal shock stands in theexit of the nozzle, as shown. Estimate (a) the pressure inthe tank and (b) the mass flow.
Carbon dioxide flows through an insulated pipe 25 m longand 8 cm in diameter. The friction factor is 0.025. At theentrance, p = 300 kPa and T = 400 K. The mass flow is1.5 kg/s. Estimate the pressure drop by (a) compressibleand (b) incompressible = flow theory. (c) For whatpipe length will the exit flow be choked?
Question 4. Consider a lifting flow (steady, incompressible) over a cylinder with a radius of R. If there are two stagnation points that are located at 0 = 21rad and 0 = a rad, then Determine the expressions for velocity and pressure coefficient. (b) Determine the maximum and minimum velocity and pressure point on cylinder. (c) Determine the expressions for stream function and velocity potential in the flow field. (d) Calculate the value of stream function on cylinder. (e) Calculate the lift produced by the cylinder. (f) Show that the drag force per unit span is zero on the cylinder. (g) If you would like to generate a flow where there is only one stagnation point at r = 2R, what should you do? Please give the exact values of the flow parameters for this configuration.
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
At a section in a nozzle (air flow), following properties are known. Po = 1000 KPa; To=500k ; V = 200 m/see é) The temperature (T) at this section is (in K), a. 480; b. 500; c. 520; d. 540; e.560 (ti) The Mach number (M) i's, a. 0.26 ; b. 0:36 ; C. 0.46;d.0.56;e.a66 3.
Question 2 //25 Q (a) In figure below the flowing fluid is Helium at 20°C. D2 =6 cm D1=10 cm Neglect losses. If pl = 1400 kPa and the manometer fluid is Meriam red oil (SG = 0.827), estimate (a) p2 and (b) the gas flow rate in m/s. R for Helium is R= 2.0769 kJ/kg/K. 0,827 1000 20+273= 293 1400 = 230 2,0769.298 Hel BT 8 cm Heliom contr 1900 - (9,81/0) 8,27 -2,30) = 932=G Q=AV,9 Q= %3D
Air at P1 = 1 MPa, T1 = 600 °C and V1 = 150 m/s enters a converging nozzle. The exit area is A2 = 50 cm2 and the back pressure is P2 = 0.7 MPa. What is the mass flow rate (kg/s) through the nozzle? What the is Mach number at the nozzle exit? What would be the flow rate you calculate if you assumed isothermal flow?
An air tank of volume 1.5 m3 is initially at 800 kPa and20 °C. At t = 0, it begins exhausting through a convergingnozzle to sea-level conditions. The throat area is 0.75 cm2.Estimate (a) the initial mass flow in kg/s, (b) the timerequired to blow down to 500 kPa, and (c) the time atwhich the nozzle ceases being choked.
The airfl ow underneath an air hockey puck is very complex,especially since the air jets from the air hockey tableimpinge on the underside of the puck at various points nonsymmetrically.A reasonable approximation is that at anygiven time, the gage pressure on the bottom of the puck ishalfway between zero (atmospheric pressure) and the stagnationpressure of the impinging jets. (Stagnation pressureis defined as p0 =1/2ρV2jet . ) ( a ) Find the jet velocity V jetrequired to support an air hockey puck of weight W anddiameter d . Give your answer in terms of W , d , and thedensity ρ of the air. ( b ) For W = 0.05 lbf and d = 2.5 in,estimate the required jet velocity in ft/s.