The shaft is made of A-36 steel. It has a diameter of 38 mm and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Part A Determine the angle of twist of gear C with respect to B. Express your answer using three significant figures. vec Figure 1 of 1 PCJB = rad Submit Request Answer B. 90 N-m 0.6 m Provide Feedback Ne 90 N-m 0.75 m 0.9m

The shaft is made of A-36 steel. It has a diameter of 38 mm and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Part A Determine the angle of twist of gear C with respect to B. Express your answer using three significant figures. vec Figure 1 of 1 PCJB = rad Submit Request Answer B. 90 N-m 0.6 m Provide Feedback Ne 90 N-m 0.75 m 0.9m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
A torque of Tp- 1335 N-mis applied to gear Dof the gear train shown. The bearings shown allow the shafts to rotate freely. Assume shafts (1) and (2) are salid 20-mm-diameter steel shafts. Determine the magnitude of the maximum shear stress acting in shaft (2). 230-mm dia. 150-mm dia. O 988.1 MPa O 898.6 MPa O 1148.0 MPa O 1098.5 MPa O 849.9 MPa
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 140-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of TA = 260 N-m. The shaft is machined from steel with Sy = 400 MPa and Sut = 560 MPa. Assume factor of safety and all other factors as (one) 1,. Determine the minimum allowable diameter of the 100-mm section of the shaft for infinite life (selectec criter sould be written at the begining of the solution) 250 mm 100 mm 20
A torque of TD= 1235 N-m is applied to gear Dof the gear train shown. The bearings shown allow the shafts to rotate freely. Assume shafts (1) and (2) are solid 26-mm-diameter steel shafts. Determine the magnitude of the maximum shear stress acting in shaft (2). 230-mm dia. TD C B 150-mm dia. O 357.9 MPa O 449.0 MPa O 415.7 MPa O 217.5 MPa O 391.8 MPa
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which 250 mm has a 150 mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T = 340 N. m. The shaft 100 mm is machined from steel with S, = 420 MPa. Using a factor of safety of 2.5, determine the minimum allowable diameter of the 250 mm section of the shaft based on a static yield analysis using the distortion energy theory and maximum shear stress theory.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
PROBLEM 1. The shafts are made of A-36 steel and both have 100 mm diameter. If a torque of 60 kN.m is applied to end E and 25 kN.m to the D gear as shown in the figure, determine the angle of twist of the section at E of the DE shaft. 0.75 m 0.75 m A B 150 mm 25 kN-m 300 mm 60 kN.m 1.25 m E
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
RIO-1. The shaft is made af A992 steel and has an allowable shear stress of Tak - 75 MPa. when the shaft is rotating at 300 rpm, the motor supplies 8 kW af power, while gears A and B withdraw 5 kW and 3 kW, respectively. Determine the required minimum diameter of the shaft to the nearest millimeter. Alka, find the rotation of gear A relative to C. 300 mm S00
The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The shaft has diameter of (14 mm ).Determine the max shear stress and the angle of twist A relative c. use G=80 Gpa 280 N.m A 150 N.m 40 N.m 0.4m 0.3m Q-2
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. Y le X 5 in-k bearing 25 in d bearing 30 in b 35 in bearing bearing TT C 2 2 in-k gear c: gear b: shaft ab: shaft ce: all shafts: radius 2.0 in radius 5.0 in radius 0.5 in radius= 0.7 in - G = 12000 ksi
A alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.