Diameter of shaft based on Strength design is in mm Diameter of shaft based on rigidity design is in  mm The sutable Diameter of the shaft is in mm The maximum shear strain is

Q: Design the smallest diameter of the solid shaft if its rotation is to produce 600 HP at 15…

A:

Q: A hollow bronze shaft (G=5000ksi) has an outer diameter of 3in and a wall thickness of 0.25in. The…

A: Given data: Converting all data into SI units. Modulus of rigidity G=5000 ksi=34473.8 Mpa Outer…

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

A: Given data:

Q: A solid shaft with a yield strength of 500 MPa subjected to a torque of 60N.m and bending moment of…

A: Step 1: Given data:Yield strength, σy​=500MPaTorque, T=60N.mBending moment, M=70N.mStep 2: We need…

Q: Find the diameter of the solid shaft. Torque = 190 kNm Maximum shear stress = 210 MN/m2

A: Substitute the given values in the Maximum shear stress equation to get the diameter of the shaft.

Q: Calculate the greatest shear stress in a hollow shaft with an outer diameter of 400 mm and an inner…

A: To find: The maximum shear stress and the angle of twist. Given: The torque applied is T=450 N.m.…

Q: A tubular steel shaft transmits a power of P = 450 hp at a speed of 3000 rpm. Determine the maximum…

A:

Q: A solid shaft is subjected to a twisting moment of 350 kNm. If the angle of twist is 5° per meter of…

A:

Q: shaft of 53 mm diameter is subjected to a bending moment of 1477158 N-mm and a torque T N-mm. If the…

A:

Q: n outside diameter of 70 m and :

A: here outer dia (70m) is >>>> inner dia (50mm). so the polar moment of inertia almost…

Q: Solve the following problem Two designs for a shaft are being considered. Both have an outside…

A: Shear stress for solid shaft is given as  τ=16*Tπ*d3=16*325*1000π*703=4.825 MPa Shear stress for…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

A:

Q: Q3 A hollow shaft with an external diameter of 160 mm transmits a maximum torque of 16 kN.m. If…

A:

Q: Let's consider a solid circular shaft subjected to the torque loads as shown. Determine the minimum…

A:

Q: ches and length 4.25 feet transmits 75 HP from an electric motor to a compressor. The allowable…

A:

Q: A hollow circular section shaft 2.5 m long is firmly supported at each end and has an inside…

A:

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

A:

Q: A mild steel shaft of 50mm diameter is subjected to a bending moment of 1.9kNm. If the yield point…

A: Introduction The maximum shear stress hypothesis states that a material will fail or yield if its…

Q: Two designs for a shaft are being considered. Both have an outside diamete of 80 m and are 100 cm…

A:

Q: A hollow aluminum propeller shaft, 30 ft. long with 15 in. outer diameter and an inner diameter…

A: GIVEN DATA-

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

A:

Q: The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner…

A:

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 226 mm and a…

A:

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

A:

Q: A solid shaft 18 m Length is to transmit power at 2200 rpm. If the shaft is stressed to 275 MPa when…

A:

Q: Lets consider a solid circuar shalt subjected to the torque loads as shown. Determine the minimum…

A:

Q: A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. If the…

A:

Q: 1. A shaft is made from AISI 1040 hot rolled steel with Su = 496 MPa, Sy = 290 MPa with 18%…

A:

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Q: A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear…

A:

Q: A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: Find the twisting moment in a solid shaft 125 mm diameter when the angle of twist is  0.5 degree on…

A: Introduction When a…

Q: QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is…

A:

Q: 1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 Ib-in. The total angle…

A: Given data: The transitted torque, T=300000 lb·in. The shear modulus, G=12000000 psi. The angle of…

Q: Finding the value of sectional modulus of shaft having diameter 3 m

A: Given data : Diameter of shaft is given in this question . With help of this data we have to find…

Q: i need the answer quickly

A:

Q: A steel shaft with a diameter 1.95 inches and length 4.35 feet transmits 80 HP from an electric…

A: Given dataDiameter = d= 1.95 incheslength = 4.35 feetAllowable shear stress = τallow = 8600…

Q: mpound shaft is made by ting a brass sleeve on a steel (which is considered as parallel ection). The…

A:

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.