The rod on the power control mechanism for a business jet is subject to a force F of 91.2 N. Determine the moment of this force about the bearing at A. Take the distance d as 120.3 mm. Answer: F 20°1 d 60° (b) Determine the horizontal force P necessary to cause motion when P is applied to Block B.

The rod on the power control mechanism for a business jet is subject to a force F of 91.2 N. Determine the moment of this force about the bearing at A. Take the distance d as 120.3 mm. Answer: F 20°1 d 60° (b) Determine the horizontal force P necessary to cause motion when P is applied to Block B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2. Choose the correct answer from a-b-c-d. 1- Determine the magnitude and direction of the moment of the force of the movement if the force at A about point P. a- Mp = 1440 NmC b- Mp = 1440 Nm Ɔ 2 m 4 m c- Mp = 600 NmC 1315 12 d- Mp = 600 Nm 260 N 3- The refrigerator has a weight of 200 lb and a center of gravity at G. Determine the force P required to move it. Will the refrigerator tip or slip? Take H = 0.4. %3D a- P = 80 lb Slips b- P = 75 lb Tips 4 ft 1.5 ft 3 ft c- P = 75 lb Slips d- P = 80 lb Tips 3 ft
The top viewv of a revolving entrance door is shown. 0.8 m Two persons simultancously approach the door and exert forces of equal magnitudes as shown. If the resulting moment about the door pivot axis at a is 25 N .m, determine the force magnitude F from the following answers which of them is correct: 0.8 m 15° O M= 16.18 N.m O M= 0 N.m O M= 18.16 N.m M = 181.16 N.m O M= 161.8 N.m
Q2. Choose the correct answer from a-b-c-d. 1- Determine the magnitude and direction of the moment of the force of the movement if the force at A about point P. a- Mp = 1440 NmC b- Mp = 1440 Nm Ɔ 2 m 4 m c- Mp = 600 NmC 13 12 d- Mp = 600 Nm Ɔ 260 N 3- The refrigerator has a weight of 200 lb and a center of gravity at G. Determine the force P required to move it. Will the refrigerator tip or slip? Take H = 0.4. a- P = 80 lb Slips b- P = 75 lb Tips 4 ft 1.5 ft 3 ft c- P = 75 lb Slips d- P = 80 lb Tips 3 ft 3.
2/33 A prybar is used to remove a nail as shown. De- termine the moment of the 240-N force about the point O of contact between the prybar and the small support block. P-30 N 16 m 240 N 16 m 15 350 mm PROBLEM 2/3s 2/36 A man exerts a force F on the handle of the stationary wheelbarrow at A. The weight of the wheelbarrow along with its load of dirt is 185 Ib with center of gravity at G. For the configuration shown, what force F must the man apply at A to make the net moment about the tire contact point B equal to zero? 65 30 mm PROBLEM 2/33 Representative Problems 2/34 An overhead view of a door is shown. If the com- 20 pressive force F acting in the coupler arm of the hy- draulic door closer is 17 lb with the orientation shown, determine the moment of this force about the hinge axin O. 20 PROBLEM 2/36 2/37 A 150-N pull T in applied to a cord, which is wound securely around the inner hub of the drum. Determine the moment of T about the drum center C. At what angle e should T be applied…
The bent rod is supported at points A, B and C by smooth journal bearings, and is subjected to force F. If dimensions a = 2.3 m, b = 1.5 m, c = 0.6 m, and d = 2.5 m, and the force F is {-2i + 9j - 3k} kN, determine the magnitude of the moment (in kN⋅m) caused by force F about point A. Answer must include 2 places after the decimal point.
Q3- The femur is subjected to the Compression forces (F1) on femoral head and the Tension forces from abductors (F2). Determine the moment of each force about the point of contact O on the femur neck. F = {50i + 60j + 800z} N F2 = {12i + 10j+ 30z} N 5cm 1cm 10.25cm 2cm 1cm Зст y
A man exerts a force F on the handle of the stationary wheelbarrow at A. The weight of the wheelbarrow along with its load of dirt is 200 lb with center of gravity at G. For the configuration shown, what force F must the man apply at A to make the net moment about the tire contact point B equal zero? Express your answer in units of lb. 60° 26" F ***** A 20° 37" W G 8"- B
Two men exerts forces of F = 80 lb and p = 50 lb %3D 6 ft P on the ropes. Determine the moment of each force 12 ft about A. Which way will the pole rotate?
The device shown is a part of an automobile seat-back-release mechanism. The part is subjected to the 4.1-N force exerted at A and a 250-N-mm restoring moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. Your answer will be positive if the intercept is above O and negative if below O. F = 4.1 N 18 mm 16° 31 mm 250 N-mm Answer: y = mm
The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. F=4N 10 mm 15° 40 mm 300 N mm SHOT ON POCO X3 NFC
Two men exert forces of P = 50lb and %3D F = 80 lb on the ropes. Determine the moment of each force about A. Which way will the pole rotate, clockwise or counterclockwise? * 6 ft 12 t
The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring exerts a restoring moment about O given by M = K(0+π/4), where K = 680 N.mm/rad and is in radians. Determine and plot as a function of the tension T required to make the net moment about O zero. The effects of the radius of the pulley at B are negligible. After you have completed the plot, answer the questions. Assume r = 55 mm, d = 120 mm. 45° T Answers: If 0 = 22°, the tension T = i If 0 = 47°, the tension T = i If 0 = 74°, the tension T = i N N N