The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring exerts a restoring moment about O given by M = K(0+/4), where K = 680 N·mm/rad and is in radians. Determine and plot as a function of the tension T required to make the net moment about O zero. The effects of the radius of the pulley at B are negligible. After you have completed the plot, answer the questions. Assume r = 55 mm, d = 120 mm. B 45° d Answers: If 8 = 22°, the tension T = If 0 = 47°, the tension T = If 0 = 74°, the tension T = i i i T Z Z N N N

The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring exerts a restoring moment about O given by M = K(0+/4), where K = 680 N·mm/rad and is in radians. Determine and plot as a function of the tension T required to make the net moment about O zero. The effects of the radius of the pulley at B are negligible. After you have completed the plot, answer the questions. Assume r = 55 mm, d = 120 mm. B 45° d Answers: If 8 = 22°, the tension T = If 0 = 47°, the tension T = If 0 = 74°, the tension T = i i i T Z Z N N N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the couple moment acting on the block,
Question 1 Determine the maximum moment in kN m in the figure below. 16 kN | 4 kN/m 20 kN 2 kN/m B D 4 m →- 8 m 8 m
In the figure, the engine of a vehicle is shown as a representation.The crankshaft of the engine around the x-axis It rotates at 4000 rpm and its moment of inertia is 0.5 kgm2 .Moving in the y direction, the vehicle enters the curve with a radius of 70 m at a speed of 120 km/h. In the meantime, find the moment coming to the motor bearings and interpret its effect on the vehicle.
Also, determine the y-component and z-component of the moment about point O. Express your answer in units of kN-m.
The horizontal force F=−Fi acting on the handle of the wrench produces a component of the moment along the OA axis (z axis) of the pipe assembly of Mz={4.1 k}N⋅m . Both the wrench and the pipe assembly, OABC, lie in the y-z plane. Suggestion: Use a scalar analysis. y-z (Figure 1) Determine the magnitude of the force F.
2b: Find the moment about points O and B from the system of forces shown below. F = 300 N A 30° F2 = 200 N 25° 250 mm 125 mm k150 mm→* -200 mm B.
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. - A = 15°1 A 250 mm lllllll 900 mm k = 2.6 kN/m OB = 30° B G 200 mm
Determine the resultant of forces and the moment at point 0 only HANDWRITTEN answer needed ( NOT TYPED)
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Magnitude of the reaction force at A in kN = 34.8 Determine the magnitude of the moment of P about the x-axis in Nm
The tension in cable CD is T=455 lb. Consider the force which this cable exerts on point C and determine its moment about point O. Assume a = 11 ft, b=4 ft. c = 7 ft, d=9ft, e = 11 ft. A Answer: Mo (i b a d T C i+ i j+ i k) lb-ft
solve by the concepts of statics on a paper with proper method
solve by the concepts of statics on a paper with proper method