The rigid bars in the figure havepivots at A and B. The lengths of thebars are AB = 1 m and BC = 1.2 m.Calculate the acceleration of point Cfor the given constant angularvelocities if \theta = 80° and \phi =60°4BC=0.8 rad/sAAB=0.5 rad/s

To calculate the acceleration of point C, we need to consider both the tangential and centripetal…

Answered: The rigid bars in the figure have…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3 Problem A hydraulic cylinder rotates around point O at a constant rate 60 deg/s and the cylinder length L is decreasing at a constant rate L = -150 mm/s. Determine the magnitude of velocity and acceleration of the endpoint B when L = 125 mm. Assume that d = 375 mm. d 0 B
In the mechanism shown below, link AB rotates at a constant angular velocity of 1.5 rad per sec counterclockwise. What is the acceleration of C along the channel? Assume the positive direction to be upwards and to the right. use relative motion
The figure shows a rigid link AB of length 2 m which rotates anticlockwise about a fixed point at A at a rate of 2 rad/s, but which is decelerating in its rotation at 1 rad/s². At the instance of time shown in the diagram, with the link AB at 60 degrees to the horizontal, what is the y-component of the absolute acceleration of point B? (The positive sense of the x and y directions are given by the axes in the diagram). O O O O O w = 2 rad/s a = -1 rad/s² 7.93 m/s2 Don't Know -7.93 m/s² 5.93 m/s2 -5.93 m/s² B 60⁰
Q1A = 12 inches, Q102 = 5 inches. The Crank Q1A rotates uniformly CCW at a speed of 75 RPM. Find the absolute linear acceleration of Body #3.
In the system on the picture the bigger wheel is not moving, the smaller wheel is connected to the center of the bigger wheel with the rod and it can rotate around the bigger wheel. the smaller wheel starts its movement with angular acceleration ε=10rad/s^2. find the acceleration of point B (marked in a drawing) after 1 full rotation. The radius of the bigger wheel is equal to 0,3m. The radius of the smaller wheel is equal to 0,1m.
Find the acceleration of the translating piston at the given instant if w1 = 10 rad/s And a, = -5 rad/s² . Present a, vector 13 in. BAR 2 form. rad/s² az in/s² w1 = 10 rad/s a1 = -5 rad/s² -BAR 1
The piston of the hydraulic cylinder gives pin A a constant velocity v = 3 [ in the direction shown for an interval of its motion. For the shown instant where 0 = 60°, solve the following: (a) Draw the polar unit vectors at the current location of the pin. (b) Determine the values of r, 0,7 and Ö where r = OA
The rigid body is rotating about the y-axis. In the position shown in Fig. (a), the angular velocity and angular acceleration of the body are as specified in the figure. Determine the velocity and acceleration vectors of point A in this position using (1) vector equations; and (2) scalar equations.
At the position shown in the figure, the velocity of the slidingcollar is ?? = 3m/s and its increasing at the rate of 1.4m/s2.a) Find the angular velocities of link AB and BC by usinginstantaneous center of zero velocity methodology.b) Find the angular accelerations of AB and BC.
Note: Read the question carefully and give me right solution clear calculations . Careful with angular velocity direction
The rigid body is rotating about the y-axis. In the position shown in Fig. (a), the angular velocity and angular acceleration of the body are as specified in the figure. Determine the velocity and acceleration vectors of point A in this position using (1) vector equations; and (2) scalar equations.
The flywheel shown in the figure is pinned at its center and for the instant shown rotates with an angular velocity w=5 rad/s and an angular acceleration a=8 rad/s². (Figure 1) 0.3 m 0.4 m The flywheel shown in the figure is pinned at its center and for the instant shown rotates with an angular velocity w=5 rad/s and an angular acceleration a=8 rad/s² (Elgure 1) Figure 1 of 1 > Figure 0.3 m 0.5 m 0.5 m 0.4m Part A Determine the angular velocity of link AB at this instant Express your answer in radians per second to three significant figures. ΑΣΦΗ vec l → C WAB rad/s Submit Request Answer Part B Determine the angular velocity of link BC at this instant Express your answer in radians per second to three significant figures. → [5] ΑΣΦ | 11 | vec ? Determine the angular acceleration of link AB at this instant Express your answer in radians per second squared to three significant figures. VE] ΑΣΦΗ vec 9 QAB rad/s² Submit Request Answer Part D Determine the angular acceleration of ink BC at…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The rigid bars in the figure have pivots at A and B. The lengths of the bars are AB = 1 m and BC = 1.2 m. Calculate the acceleration of point C for the given constant angular velocities if \theta = 80° and \phi = 60° 4BC=0.8 rad/s A AB=0.5 rad/s