By the method of this article, determine the angular velocity WAB (positive if counterclockwise, negative if clockwise) of link AB and the velocity vg (positive if up, negative if down) of collar B for the instant represented. The quantities wo = 2.32 rad/s and r = 270 mm.

Q: If musS m= So kg & 9- 1o Find requised farce f to just Sturt the mo tion

A:

Q: Given the following duty record, how much life is consumed? 500 cycles 2000 cycles (600 000 +…

A: The life consumed and remaining life for 900RPM needs to be evaluated. The workload history is given…

Q: Find the length in feet 0f 9/16 inch diameter rope required to fill a drum having the following…

A:

Q: In the figure shown, I=140mm, b=40mm and WAB=1100rpm (clockwise) Solve for (a) the velocity(m/s) of…

A: Given data  l=140 mm b= 40mm Wab = 1100rpm thetha= 65° find the velocity of P and angular velocity…

Q: Can any help find the reactions and moments for the this  problem.

A: Given data as per question

Q: :O38/ Given the followtng data, the chear stress value at segment BC is G 80 GPa Diameter= 2e m 沙…

A: Find the shear stress in segment BC.

Q: Q: Shaft rotates 3500 rpm clockwise and carrying gear A. Compute 1. the train value for the train.…

A:

Q: dar Grub planar mcchanism to be one. The mumber of degrees of freedom for below mentioned…

A:

Q: 4. Ø.009MAB@ Answer:

A: refer generalized representation of geometric tolerance.

Q: oblem 7: Non-circular cross section shaft related to torque problems are difficult to be solved…

A:

Q: The non-linear spring shown in the image below has a stiffness, K, given by the equation: K= 7 - 5u…

A: Given: K = 7-5u To find: Extension of the spring

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A: P= 48512 N Length of steel, Ls= 1.42 m Length of bronze, Lb= 2.36 m Area of steel, As= 639 mm2…

Q: Algebraic reduction S=27C$ for small attenuation. Show that s has the following relationship with…

A:

Q: S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute…

A: The answer is given in the below

Q: Find wark done F = 2.221N d=1-22m

A: Given data : Force=F Displacement=d   Required : Work done

Q: Engine has a capacity of 20 milliliters per cylinder and the length of the axle arm is 5 cm Find the…

A:

Q: Determine the force in member AB of the truss. Express your answer to three significant figures and…

A: P1 = 2KN  P2 = 1.5KN

Q: Find the values of a₁, 02 and as for the semidefinite system with J₁ = J₂ = J3 = Jo, kt1 = k₁, and…

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: A force F : about the point (1, 5, 0) ft. Find Fy. - 4i + Fj – 9k lb acts at a point (3, – 8, 6) ft…

A:

Q: If W-100 N and u-0.5, then the friction force of the block shown in figure is

A: Solution:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: ## Moment of Inertia Calculations (by hand)**Given:*** a = 22 ft* y = x^2 (for part a)* y = x (for…

Q: Ay X 12

A: given:

Q: Part D As shown a system of cables supports a bucket. (Figuts 2) The dimensions in the figure are as…

A: Given Weight = 20.5 lb To find Tension  TA TB TC

Q: The value of the spring index for a helical spring is 14. Calculate the outer diameter of the spring…

A:

Q: -800 Dimensions in mm F1 600 F2 F3 900 -560--480- What is the x component of F1=701 N?

A:

Q: Find the work done Force=0.433 N Displacement=0.22 m

A: Given data : Force=F Displacement=d   Required : Work done

Q: Determine the vertical displacement of point C in inches by using he method of virtual work. A is a…

A:

Q: Draw the hexagonal headed bolt with a nut and a washer with

A:

Q: Given the figure below. Find the momemt of F about O. 4 ft F, = {100i – 120j + 75k} lb 5 ft. 3 ft

A:

Q: Pin T A 3 m 4*う B 100 N 100 N Fac 4m 50 N F3c sc '50N Rolfer 19501 4 m Roler FA FAB Pac 3 Ray R Ax…

A: to determine -  Fab , Fbc , Fca

Q: how to get the -y theo

A:

Q: L,=40mm; L,= 120mm; L,=80mm L=100mm and 0,=65°. Find the possible value of 0, and and 0,

A:

Q: Q1-1) See Figure 1, classify each of the structures as statically determinate, statically…

A:

Q: Problem The intermediate shaft in the two-stage gearbox shown below is to be designed. The…

A:

Q: In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element…

A:

Q: Find: (Answers should be 6 sig figs) -Area -Ix(bar) -Iy(bar) -Iz (bar) aka polar moment of inertia…

A: Consider the given section as follows : The semi circle is first element and the rectangle is…

Q: Determine the position of the x-centroid in mm.

A:

Q: 6 kN C a a g 6 kN -b f 0.1 m 0.125 m

A: To determine the number of forces in the following picture

Q: 5. A wire made of the same material (Y= 12X101ºPA) is cut into two parts, we label it as wire I and…

A: Given: Young's modulus E=12×109PaLength of Wire II=L2Diameter of Wire II=D2Length of Wire I…