As shown in the figure, the right-angled bar OAB rotates uniformly around the O-axis, and the angular velocity is . AB is fitted with a small ring M, which is also fitted with a large fixed ring. At the moment shown in the figure,OMO1 is on the same horizontal line, the radius of the big ring is known as R,001=3R, and Please calculate the speed and acceleration of the instantaneous small ring 30 M B 0₁ R

As shown in the figure, the right-angled bar OAB rotates uniformly around the O-axis, and the angular velocity is . AB is fitted with a small ring M, which is also fitted with a large fixed ring. At the moment shown in the figure,OMO1 is on the same horizontal line, the radius of the big ring is known as R,001=3R, and Please calculate the speed and acceleration of the instantaneous small ring 30 M B 0₁ R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the angular acceleration of bar BC for the moment indicated in the diagram. Bar AB has a constant clockwise angular velocity of 5.3 rad / s and the dimensions are as follows: x1 = 13 m, x2 = 20 m, y1 = 16 m, y2 = 19 m.
At the moment shown in the figure, it is known that the rod in the vertical direction moves downward with a speed of v=0.8 m/s ederken and has an acceleration = 1.2 m/s2 upward. At this moment in question: a. The angular velocity of the AB rod, b. Bis the speed of the sliding bearing. c. The angular acceleration of the AB rod, d. Find the acceleration of B sliding bearing. Note: Take the R as 0.4m.
The disk in Figure, rotates about a fixed axis throughO with angular velocity ω =5 rad/sec and angularacceleration α = 3 rad/sec2in the directions shown at acertain instant. The small sphere A moves in the circularslot, and at the same instant, β = 30°, ?̇ = 2rad/sec, and?̈ = - 4 rad/sec2. Determine the absolute velocity andacceleration of A at this instant.
Find the acceleration of the translating piston at the given instant if w1 = 10 rad/s And a, = -5 rad/s² . Present a, vector 13 in. BAR 2 form. rad/s² az in/s² w1 = 10 rad/s a1 = -5 rad/s² -BAR 1
If the body AB rotates counterclockwise with an angular velocity oa = 6 rad / s, find the angular velocity of the BC rod and the velocity of the C block at the moment shown in the figure below. The BC bar is horizontal at the moment shown.
In reference to the figure, @ 1 ft Given: v = 8 ft/s w = 2 rad/s Determine the velocity in ft/s of point C of the cylinder at this instant assuming that the cylinder rolls counterclockwise without slipping while the conveyor belt moves to the right. TIP: Use the IC method
In the mechanism shown in the figure, AB = 8 meters BC = 5 meters CD = 4 meters. L = 3 meters. When the bars AB and CD are parallel and horizontal, the AB rod has an angular velocity w = 2rad / s and a = 1rad / s ^ 2 angular. What is the velocity of point C and the angular acceleration of the CD rod at this moment?
In the mechanism shown in the figure, the OE crank rotates with a constant angular velocity of 3 rad/s. At the moment shown:a. find the velocity of the Point C, which is the center of mass of the disk, andb. find the angular acceleration of the disk.
Ring C moves downwards at 2 m/s. Determine the value of point B velocity (vB =?), Angular velocity of the arm CB (wBC) and the position vector B in relation to C rB/C for the situation shown in the figure.
3- The crank, connecting rod and cross head of a stationary steam engine are shown diagrammatically in fig. The 22.5 cm crank arm BC is rotating at a constant rate of 150 rpm. The length of the connecting rod AB is 80 cm. Find the velocity and acceleration of the cross-head A when 0=45°. The cross-head moves on a horizontal line through C. B 1
A gear of mass m = 10 kg and radius R=0.25 m may rotate about its center of mass C, which is fixed. A rack of mass m = 10 kg is subjected to a constant force Fo = 20 N, as shown. The rack and gear are geared together (gear teeth not shown), so that the force Fo drives the rack to the right and rotates the gear. Find the angular ácceleration a of the gear and find the force f exerted by the rack on the gear. The gear is to be modeled as a uniform circular disc. Fixed Fo3 20 N Rack
The rod OA rotates clockwise at a constant angular velocity of 0 = (3) rad -. Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equationr = (250 · (8 - cos 0)) m. Hint: 1. Remember clockwise rotation is negative velocity. A d3 d1 d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 01 130 degrees di 0.45 m d2 dz 0.2 m 0.325 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, vr and b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, a, and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, v d. Determine the cylinder's magnitude of the acceleration at the instant shown, a