The principal stresses shown below are calculated at two different cross sections of a brittle machine part. Determine if the cross section A or B is safer (Sy = 50 MPa, Sut= 100 MPa, and Suc = 200 MPa). 0,50 MPa. a₂=-20 MPa A 0₂ = -20 MPa 0₁ = 50 MPa 0,20 MPa. %₂=-120 MPa B %₂=-120 MPa a₁ = 20 MPa

The principal stresses shown below are calculated at two different cross sections of a brittle machine part. Determine if the cross section A or B is safer (Sy = 50 MPa, Sut= 100 MPa, and Suc = 200 MPa). 0,50 MPa. a₂=-20 MPa A 0₂ = -20 MPa 0₁ = 50 MPa 0,20 MPa. %₂=-120 MPa B %₂=-120 MPa a₁ = 20 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a point in the cross-section of an engineering component an element is subject to the following stresses: σx =100MPa σy =45MPa τxy = -50MPa Construct a Mohr’s Stress Circle and hence determine: (a) The Principal Stresses (σ1 & σ2) and the Directions of the Principal Planes (φ1 & φ2) (b) The Maximum Shear Stress (τmax) (c) Find the Normal Stress (σn) acting on a plane at 40 degs anticlockwise from the y-axis
In a volume element with dimensions dx, dy, dz the negatíve y-face has a 2 MPa stress in the positivex-direction, a 3 MPa stress in the negative z-direction, and a 4 MPa stress in the negatíve y-direction. Which of the following describes the stresses per elasticity convention? Oyy = 4 MPa Oyr = -2 MPa 3 MPa A MPa
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
The steel bolt and anchor assembly is used to reinforce the roof of a passageway in an underground coal mine. In installation, the bolt is tensioned to 5,500 lb. Calculate the stress, strain, and extension of the bolt with length I= 39 in. if it is formed from 1045 steel alloy. Coal seam Passageway in. Roof line (Express your answer using three significant figures.) |ksi (Express your answer using two significant figures.) |×10-4 (Express your answer using whole numbers.) mils AL = %3D
Determine the nodal displacements and the element stresses. E = 105 GPa, v = 0.3, and t = 5 mm. You don't have to calculate everything manually, but can write a code to get some input from you and find the stiffness matrices for instance. 400 mm 3 5 400 mm 30 kN 2
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. A parameter value units 470 mm 400 mm 40 mm 30 mm 30 KN cc 080 BY NO SA 2021 Cathy Zupke L₁ L2 d₁ d₂ P 4₁ B C E The stress in AB σAB= The stress in CD and EF: OCD = EF= d₂ L₂ MPa D F MPa
b=3.1m a=2.1m (1) B C = 2m P = 80kN C d = 1.8m WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES dia of rod 1 = 13mm dia of rod 2 = 11 mm
The solid circular rod has a cross-sectional area of 310 mm2. It is subjected to a uniform axial distributed loading along its length of w = 10 kN/m. Two concentrated loads also act on the rod: P = 4 kN and Q = 2 kN. Determine the normal stress in the rod at x = 0.2 m. Assume a = 0.6 m and b = 1.3 m. >P → → → → -> B A |C a b Answer: 0 = i MPa
10/10 find the tensile stress in upper plate in section 3-3 5. 1 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 2) 300 mm 8 mm
The following stress condition is applied on a material: 400 200 0 O = 200-300 0 MPa 000 Determine the principal tensile stresses and its angle with respect to the x axis. Determine the maximum shear stress and at its angle with respect to the x axis.
1. We can visualize the factor of safety for an arbitrary stress using a surface in principal stress space. For a ductile material that yields according to a von Mises criterion with a yield stress σy, sketch the von Mises surface in σ₁ - 02 space and sketch the stress surface that corresponds to a factor of safety FoS = 2. For a brittle material that yields according to a max normal (Rankine) criterion with a tensile strength Gyt and a compressive strength σvc = 20yt, sketch the yield surface and the surface that corresponds to a factor of safety FoS = 2.