Determine the nodal displacements and the element stresses. E = 105 GPa, v = 0.3, and t = 5mm. You don't have to calculate everything manually, but can write a code to get some inputfrom you and find the stiffness matrices for instance.400 mm35400 mm30 kN2

Step 1: Step 2: Step 3: Step 4:

Answered: Determine the nodal displacements and…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3) Solve the plane stress problem using two-element model to find displacements and stresses. 15 kN 30 mm E-70 GPa Thickness - 10 mm
stress element x=21Mpa, y=11Mpa, xy=8, angle=50 degrees using the arithmetic method and Moore's circle 1) Find the main stresses, their directions, and be the maximum shear stresses ) Find the maximum and minimum stresses when rotating at the given angle in the positive direction
The internal loadings at a section of the beam in (Eigure 1) are shown Figure 20 mm 100 mm 200 mm 20 mm 10 kNm 20 mm 10/12 60 kN 80 KN 500 N-m Determine the in-plane principal stresses at point C. Also compute the maximum in-plane shear stress at this point Express your answers, separated by commas, to three significant figures. VAZ Ivec 4 d Submit Provide Feedback T Wha Bequest Answer ? MPA, MPA, MPA
please step by step solve this simple algebra. it s part of a stress and elasticity problem
F1=603N F2 =818N show a detailed solution please
QUESTION 4 Figure 3 below shows a vertical rod under its own weight. Find the displacement at A and stress distribution. Use E-100 MPa and weight per unit volume 0.06 N/cm³. Solve using two elements and comment on the stress distribution. 1.6 m 1m A Area = 2500 cm² 8 B Area = 1500 cm²
Question 5 A 120 mm x 100 mm x 20 mm T section short column is used as a simply supported beam. The beam carries the applied eccentric load F of 120 kN at the position indicated in Figure Q5. Start your calculations be setting an origin from the right-most point on the cross-section and determine the following: 100 120 mm 20 mm F 20 mm Figure QS: T- section short column beam 5.1 The maximum compressive and tensile longitudinal direct stresses induced in the column. 5.2 Plot the stress distribution diagram and determine the position of the NA.
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 48512-Nload, using the following data: length of steel = 1.42 m, length of bronze = 2.36 m Area of steel = 639 mm, Area of bronze = 319 mm Modulus of elasticity of steel = 180 Gpa, Modulus of elasticity of bronze = 81 Gpa x = 0.58 m, y = 1.13 m, and z = 0.72 m. Round off the final answer to two decimal places.
You need the shear modulus for a particular material in order to calculate shear strain for a known applied shear shear stress. You can't find shear modulus for the material, but you can find elastic modulus (200 GPa) and Poisson's ratio (0.3). Which of the following could you use as the shear modulus for your calculations? 200 GPa O 60 GPa O 77 GPa O 154 GPa
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
1. This question relates to stresses due to combined loading. A shaft subjected to combined torsion and axial thrust is designed to resist a shear stress and a compressive stress as shown in Figure Q1. Using the information provided in Table Q1: Figure Q1 Txy 90 mpa ox 130 mpa a) Determine the principal stresses and show them on a sketch of a properly oriented element. b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. c) Calculate the safety factors according to the three theories (Rankine, Tresca, and Von- Mises). Take the yield strength of the material as, Oyield = 250 MPa. d) Sketch the Mohr's circle for the stressed component location and indicate the stress states, principal stresses, and maximum shear stress.
Find the stress in members DF, FI, and HI if the cross- sectional area of each member is 800 mm?. Indicate Tension or Compression. E 3m -2m- 2m- 3m 30KN 10KN 3m K Find the following DF: Force P Stress FI: Force P Stress HI: Force P Stress C.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Determine the nodal displacements and the element stresses. E = 105 GPa, v = 0.3, and t = 5 mm. You don't have to calculate everything manually, but can write a code to get some input from you and find the stiffness matrices for instance. 400 mm 3 5 400 mm 30 kN 2