Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 3.5-kg slender rod AB and a 2-kg slender rod BC are connected by a pin at B and by the cord AC. The assembly can rotate in a vertical plane under the combined effect of gravity and a couple M applied to rod BC. In the position shown, the angular velocity of the assembly is zero and the tension in cord AC is equal to 26.8 N. 300 mm A 400 mm с 400 mm M B Determine the angular acceleration of the assembly. (You must provide an answer before moving to the next part.) rad/s2 The angular acceleration of the assembly is O.

Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 3.5-kg slender rod AB and a 2-kg slender rod BC are connected by a pin at B and by the cord AC. The assembly can rotate in a vertical plane under the combined effect of gravity and a couple M applied to rod BC. In the position shown, the angular velocity of the assembly is zero and the tension in cord AC is equal to 26.8 N. 300 mm A 400 mm с 400 mm M B Determine the angular acceleration of the assembly. (You must provide an answer before moving to the next part.) rad/s2 The angular acceleration of the assembly is O.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
Question 1 The slide crack mechanism of a sports motorcycle is shown in Figure 1. The net force experienced by the vertically positions piston is 2257 N. Whereas, the piston has a diameter, and the stroke length is 100 mm and 120 mm, respectively. The linear velocity of the piston is 5.3 m/s and the angle between the line of action of the piston and the crack (OB) is 0 = 20°. 250 mm B 60 mm Figure 1: slide crack mechanism of a sports motor bicycle 1.1. If the mass of the piston is 1.1 kg and the force acting vertically downward on the piston due to the internal combustion in the cylinder is 5500 N, calculated gas pressure resulting from the combustion. 1.2. Create a vector diagram to calculate the speed of the crank if the piston speed is 5.3 m/s vertically downwards. 1.3. What is the acceleration of the piston?
The Block with a mass of 4-Kg is hung with a spring. The stiffness constant of the spring K = 10 N/cm. The block is at rest position at point A with a 4-cm stretched of spring. Block is pulled down immediately with a force F=100-N Calculate the velocity of block when it passes point B which is 5-cm away from point A. K. 10 N/cm. 4 kg. VA- O A 5.cm. F = 100-N ---- --- VB = ?
4. A loaded governor of the Porter type has equal arms and links each 250 mm long. The mass of each ball is 2 kg and the central mass is 12 kg. When the ball radius is 150 mm, the valve is fully open and when the radius is 185 mm, the valve is closed. Find the maximum speed and the range of speed. If the maximum speed is to be increased 20% by an addition of mass to the central load, find what additional mass is required. [Ans. 193 r.p.m.; 16 r.p.m.; 6.14 kg]
Q. The upper and lower arms of Porter governor are 0.25 m each and are pivoted 30 mm from the axis of rotation. The radius of rotation Is 130 mm. The mass of the ball and sleeve are 3 kg and 38 kg respectively. Find the effort and power of the governor.
Consider a person who momentarily puts all of their body weight on one leg when walking or running. The forces acting on the leg and the corresponding biomechanical model of the system are shown in Fig.- Prob. 10(a) and (b). Point O corresponds to the center of rotation of the hip joint. A is the connection point of the hip abductor muscle with the femur; point B is the center of gravity of the leg; and C is the point of application of the ground reactive force. The distances between point A and points O, B, and C are: a = 8.6 cm, b = 34.3 cm, and c = 89.4 cm. The angles formed by the femoral neck and the longitudinal axis of the femur with respect to the horizontal are alpha = 43° and beta = 79°, respectively. Furthermore, for this position of the person standing on one leg, it has been estimated that the magnitude of the force exerted by the hip abductor muscle is FM = 2062.6 N and its line of action forms an angle of theta = 69° with respect to the horizontal. If the magnitude of…
In his mission as a spy, Loid Forger fired a bullet weighing mB = 0.007 kg with a horizontal speed of VB= 550 m/s into the lower end of a gate which can be modeled into a slender m=16-kg bar of length L=1.5m for simplified analysis only. Know that h=0.25 m and that the gate, which has a pin connection at point C, is initially at rest. The bullet becomes embedded into the gate after impact. 1.5 m с A D 0.25 m VB= 550 m/s
D 3. Two masses, mÃ = 2.0 kg and må = 7.0 kg, are on inclines as shown and are connected by a massless string. The coefficient of kinetic friction between mA and the incline is 0.25, while the coefficient of kinetic friction between me and the incline is 0.35. Assume that mÃ moves up the incline and m³ moves down the incline. a. Draw an FBD for each mass. b. Find the acceleration of the masses. MA 51° mB V 21°
An arborist is cutting down a tree a 28 m high tree bystarting his cut 1.8 m above the ground. The tree has a mass of 3750 kg. The tree trunk can be thought of as a uniformly dense, thin rod. 1. What's the speed of the tree’s center of mass when the trunk is parallel to the ground on its way down. The tree rotates about the point where it is cut., 1.8 m above the ground. 2. What is the total amount of kinetic energy that the tree has at thatpoint of parallelism to the ground? How fast would a 950.0 kg truck have to be traveling to have the same kinetic energy as the tree?
=↑ -7----- mg Sw mg 2. A drone of mass m (shown above) moves with a horizontal velocity v and is propelled by a thrust force ft produced from its propellers. To move, it tilts itself by an angle 0, which causes the thrust force ft to take on a component in the horizontal direction. This forward-directed force is indicated by ff in the diagram above. The drone is also subject to an aerodynamic drag force fa that acts in a horizontal direction and is proportional to forward velocity according to fa= -bv (regardless of 0). (a) Assuming ft acts along the inclined axis of the body, find ff as a function of the tilt angle and ft. (b) Find the necessary thrust ft needed to ensure that lift is balanced by gravity so that the drone does not move vertically. That is, find ft such that its vertical component as shown is equal to mg. Your answer will be a function of 0, g, and m. (c) Give the the small-angle approximations of these two functions when ≈ 0. (d) Suppose the drone has a mass m = 1 kg…
simultaneously. 0 = The robot arm is elevating and extending At a given instant, 0 = 37°, 43 deg/s, 0 = 113 deg/s²,1 = 0.51 m, i = 0.33 m/s, and Ï = -0.40 m/s². Compute the radial and transverse forces Fr and Fe that the arm must exert on the gripped part P, which has a mass of m = 8.8 kg. Compare with the case of static equilibrium in the same position. Assume d = 0.55 m. m 6 SAAREPARA Answers: Dynamic: Fr= i FON, i Static: F₁= FON, i
Q3/A shaft carries four masses A, B, C and D of magnitude 20 kg, 30 kg, 40 kg and 20 kg respectively and revolving at radii 80 mm, 70 mm, 60 mm and 80 mm in planes measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks measured anticlockwise are A to B 45°, B to C 70° and C to D 120°. The balancing masses are to be placed in planes X and Y. The distance between the planes A and X is 150 mm, between X and Y is 450 mm and between Y and D is 100 mm. If the balancing masses revolve at a radius of 150 mm, draw the space diagram and find their magnitudes and angular positions of the balancing masses. (