The steel bolt and anchor assembly is used to reinforce the roof of a passageway in an underground coal mi In installation, the bolt is tensioned to 5,500 lb. Calculate the stress, strain, and extension of the bolt with length I = 39 in. if it is formed from 1045 steel alloy. Coal seam Passageway 을 in. Boof line

The steel bolt and anchor assembly is used to reinforce the roof of a passageway in an underground coal mi In installation, the bolt is tensioned to 5,500 lb. Calculate the stress, strain, and extension of the bolt with length I = 39 in. if it is formed from 1045 steel alloy. Coal seam Passageway 을 in. Boof line

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel rod with a cross-sectional area of 0.25in .^ 2 is stretched between two fixed points. The tensile load at 0.7 deg * Fis * 1200 lb. What will be the stress at 0 deg * F ? At what temperature will the stress be zero? Assume alpha = 6.5 * 10 ^ - 6 in ./(in*^ F) and E = 29 * 10 ^ 4 psi.
please include fbd and complete solution
h.w: A compressive force was applied in the longitudinal direction of a cross-sectional bar ( A= 10 cm) and this resulted in a longitudinal strain of (0.0007) Calculate the amount of force? If you know that the elastic modulus (E= 206*10° m2
This is a subject of strength of materialsShow complete solution and clear hand writing no shortcut pls shoe free body diagram and pressure diagram thank you
The two angle bars are used to support a tensile load "T". Assume the tensile load to be equally resisted by each angle. 400 mm x 20 mm THK Gusset Plate The steel used is L 6 x 6 x 1. Properties: A = 7096.76 mm? y = 47.244 mm Fy = 248 MPa Fu = 400 MPa b = 152.4 mm b. t = 25.4 mm x = 47.244 mm Effective hole diameter = 25 mm y Use case 2 for shear lag factor. Use NSCP 2015 code. 1. Determine the maximum allowable load that can be carried by the two L6 x 6 x1 based on yielding of the gross section--- 2. Determine the maximum factored load that can be carried by two L6 x 6 x 1, based on the fracture of the effective net area.---- 3. Determine the maximum allowable tensile load that can be carried.------ 4. Determine the maximum factored tensile load that can be carried-- bo
Pls box ur answer thx u
Learning Goal: A material is homogenous and isotropic when it has a modulus of elasticity that does not vary with direction and it has uniform properties throughout. When a point in a material is subjected to only normal stresses in three dimensions, but they are not necessarily equal, the state is called triaxial stress. When the response of the material is linear elastic, the strains along the three axes can be calculated using a generalized form of Hooke's law. Each strain depends on all three stresses because of the Poisson effect. €1 Figure 1 [0₂ - V (O₂ +0₂)] a 1 of 1 A cube is subjected to stresses with magnitudes a = 16 MPa, b = 26 MPa, and c = 5 MPa (Figure 1). What is the strain in the y-direction? Let E = 200 GPa and v= 0.26. Express your answer to three significant figures. ► View Available Hint(s) Submit VE ΑΣΦ Part B - Change in volume f change in volume = vec The cube from Part A originally has side length 3.2 cm . What is the change in volume of the cube under the given…
A solid bar of length L = 4 m and diameter 200 mm is heated from 20 to 320 degrees celsius and restrained between two solid immovable walls. Young's modulus of the material is 90 GPa and the coefficient of thermal expansion is 22 x 10-6/°C. →Calculate the thermal strain, e, in micro-strain correct to two decimal places. micro-strain. Calculate the thermal stress, o, in megapascals (MPa) correct to two decimal places. E: σ: MPa. Hence calculate the force exerted by the bar in meganewtons (MN) correct to two decimal places: F MN. L
A steel wire is 10m long supports a tensile load of 2000N. What is the diameter if the stress is 140 MPa & the total elongation is 5mm.E=200 GPa.
Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a stress-strain curve Homework- help Table 3-2 The results of a tensile test of a 0.505 in. diameter aluminum alloy test bar, initial length (1o) = 2 in. Calculated LTO Load (Ib) Change in Length (in.) Stress (psi) Strain (in./in.) 0.000 1000 0.001 0.0005 4,993 14,978 24,963 34,948 37,445 39,442 39,941 39,691 37,944 3000 0.003 0.0015 5000 0.005 0.0025 7000 0.007 0.0035 7500 0.030 0.0150 7900 0.080 0.0400 8000 (maximum load) 0.120 0.0600 7950 0.160 0.0800 7600 (fracture) 0.205 0.1025
Calculate the maximum stress in a 25 mm thick perforated bar and show its location on the figure.
250 mm Q1: The beam shown in Figure 1 is subjected to a vertical force Py and a horizontal force Pr The data for P Pr, a L,and e are shown in Table1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv > 135 KN 55 omm a I=> 6omm Ph 2248KN 120 mm L =2 600mm Figure 1