The internal shear force V at a certain section of an aluminum beam is 10.6 kN. If the beam has the cross section shown (assume a=39mm, by 72 mm, tw-t-5 mm, d-84 mm), determine:(a) the shear stress rat point H, which is located 39 mm above the bottom surface of the tee shape.(b) the maximum horizontal shear stressmax in the tee shape.HAnswers:(a) T₁ =(b) TmasVMPa.MPa.

Answered: Image /qna-images/answer/8f6996ff-c18d-4378-a955-dd4326ff57ea.jpg

The internal shear force V at a certain section of an aluminum beam is 10.6 kN. If the beam has the cross section shown (assume a-39 mm, by 72 mm, tt-5 mm, d-84 mm), determine: (a) the shear stress t at point H, which is located 39 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress max in the tee shape. by H Answers: (a) T₁ = (b) m V MPa. MPa.

The internal shear force V at a certain section of an aluminum beam is 10.6 kN. If the beam has the cross section shown (assume a-39 mm, by 72 mm, tt-5 mm, d-84 mm), determine: (a) the shear stress t at point H, which is located 39 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress max in the tee shape. by H Answers: (a) T₁ = (b) m V MPa. MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The internal shear force V at a certain section of an aluminum beam is 8.6 kN. If the beam has the cross section shown (assume a=37 mm, b-63 mm, t-t-6 mm, d-71 mm), determine: (a) the shear stress TH at point H, which is located 37 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. a H Answers: (a) TH= (b) Tmax bf V how H MPa. MPa.
P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15 kips. The beam has length L = 6 ft. (a) Calculatethe principal normal stresses and the maximumshear stress for an element located at C near the fixedsupport. Neglect the weight of the beam. (b) Repeat Parta for point D which is 4 in. above point C (see figure).See Table F-1(a), Appendix F, for beam properties.
Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa
The strain in the x direction at point A on the A-36 structural-steel beam is measured and found to be εx = 217 x 10^6. Determine the applied load P. What is the shear strain γxy at point A?
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
The internal shear force V at a certain section of an aluminum beam is 8.5 kN. If the beam has the cross section shown (assume a=32 mm, bf=65 mm, tw=tf-7 mm, d=89 mm), determine: (a) the shear stress T at point H, which is located 32 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. a Answers: (a) TH i MPa. (b) Tmax MPa. H = bf y V d
In the following figure, the steel plate must support maximum load of P=130 kN. The ultimate shear stress of the steel is Tu=342 MPa. Knowing that the diameter of steel bolts is d=27 mm, determine the factor of safety used for this design. (Hint: The steel plate is attached to a beam using three steel bolts) P Factor of Safety:
! Required information Consider the given state of stress. to A16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 10° counterclockwise, using Mohr's circle. The normal stress ox'is ksi and oy'is |ksi. The shear stress Tx'y'is ksi.
Please answer correctly, badly need it. Thank u godbless The internal shear force at a certain section of a steel beam is V= 8.8 kN. The beam cross-section shown in the figure has dimensions of b=141 mm, c=31 mm, d=63 mm, and t=6 mm. Determine: (a) the shear stress at point H. (b) the shear stress at point K. (c) the maximum horizontal shear stress in the cross-section. Break the cross-section into five rectangles, as shown. It is seen that the two labeled with a (1) are identical, and the two labeled with a (2) are identical. Find A1, the area of rectangles (1), and y1, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (1). Similarly, find A2, the area of rectangles (2), and y2, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (2). Then, find A3 and y3 for rectangle (3). A1= mm2 y1= mm A2= mm2 y2= mm A3= mm2 y3= mm Find y¯, the vertical…
Reaction force Pin Retaining ring Ⓡ Force on link
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 2.8 in.?. Assume a = 2.75 ft and b = 3.30 ft. If the normal stress in each member must not exceed 55 ksi, determine the maximum load Pmax that may be supported by the structure. E a В Answer: Pmax kips